BEFORE USING THE APPLIANCE FOR THE FIRST TIME CAREFULLY READ THIS QUICK REFERENCE GUIDE AND THE ASSEMBLY INSTRUCTIONS!
THE CONTROL PANEL OF THIS DISHWASHER ACTIVATES PUSHING ANY BUTTON EXCEPT CANCEL/OFF BUTTON.
FOR ENERGY SAVING THE CONTROL PANEL DEACTIVATES AUTOMATICALLY AFTER 30 SECONDS IF NO CYCLE HAS STARTED.
PROGRAMS
SELECTION
BUTTON
Push “Programs”
button (repeatedly)
until the indicator of
the required
program lights up
(see “Table of
programs” - next
page).
ANTIBACTERIAL
3)
RINSE
This function activates an
antibacterial rinse at the
end of the wash cycle,
guaranteeing a further
reduction of bacteria.
Press the button to
activate or deactivate the
function.This function
can be used with the
programs indicated in the
table of programs. The
dishwasher door must
be kept shut for the
entire duration of the
program in order to
guarantee reduction of
bacteria. If the door is
opened the indicator
lamp starts flashing.
TABLET SETTING
This setting allows to
optimize the cycle
performances according
the type of detergent
used. Push the Tablet
button for 3 seconds
(until the indicator lights
up) if you are using the
combined detergents in
tablet (rinse aid, salt and
deteregent in 1 dose). If
you are using powder
detergent or liquid
detergent, the Tablet
indicator on the control
panel has to be off.
DELAYED
START BUTTON
The wash cycle
can be
programmed to
start after 2, 4 or 8
hours. Then press
the Start button.
The wash
program will start
after the set time.
START/RESUME
BUTTON
Push this button to
start the selected
program: the indicator
lights up and goes off at
the end of the
program. When the
door is opened during
a washing cycle, the
cycle is temporarily
paused: the Start
indicator blinks. To
resume the cycle close
the door and push
Start button again.
CANCEL/OFF
BUTTON
Push this button to switch
off the control panel.
If pressed when a
program is running it
cancels the program
ongoing draining water
for 1 minute.
If pressed when the
dishwasher is switched
off it drains any possible
liquids from dishwasher
(1 minute process).
If the indicator flashes
repeatedly, see page 9 chapter ”What to do if ...”.
RINSE AID
INDICATOR
When lit (at the
end of the
cycle), the rinse
aid dispenser
needs to be
refilled.
5019 396 01947ADG 4624
SALT
INDICATOR
When lit (at the
end of the
cycle), the salt
reservoir needs
to be refilled.
GB
-1-
Quick reference guide
Chart
Table of programs
P
1Pre-Washcold
2Glasses40°C
3Quickwash45°C
4
5Intensive70°C
Programs
2)
Eco
50°C
Consumption
Deter-
Available
options
DelayCrockery to be washed later.—4.00.0314
Delay
Delay
Delay
Antibacterial
rinse
Delay
Antibacterial
rinse
Light soiling, for example glasses and
cups.
Lightly soiled crockery, with no dried-on
food.
Normally soiled crockery.
Energy-saving program.
Recommended program for heavily soiled
crockery, especially suitable for pans and
saucepans.
Loading instructionsLitreskWh
gent
X10.00.85100
X11.00.8030
X12.01.05170
X14.01.55155
Minutes
1)
1) Program data obtained in conformity with European standard EN 50242, obtained under normal conditions (without additional options)
and may vary depending on conditions. Differences of up to 20 minutes are possible with sensor programs as a result of the appliance’s
automatic calibration system.
2) Reference program for energy label in compliance with EN 50242 regulations. - Note for Testing Institutes: for detailed information on
the EN/Standard loading comparison test and other tests, contact the following address: “nk_customer@whirlpool.com”.
3) The antibacterial action has been tested by the Institut Pasteur of Lille (France), based on the NF EN 13697 standard of November 2001.
GB
-2-
How to set water hardness in order to always assure the best cleaning results
First time use
1- salt reservoir
2- rinse aid dispenser
3- detergent dispenser
4- racks system
5,6,7,8- available functions on the panel
9- filters
10- spray arms
Water hardness should be set
only before the first wash or if
water hardness has been
changed
Water hardness level is
factory set for medium-hard
water (level 4).
Even if you use tablets
which include salt
functionality, you must still
add regeneration salt since
such detergents are not
effective enough at
softening hard water.
At first time use, the salt reservoir has to be filled independently from water hardness level
Filling the salt reservoir -
1
The salt level indicator lamp may remain lit
at the end of several wash cycles. If the
water hardness level falls within category
(soft), no salt is required.
Dissolve limescale (not necessary if water hardness level is set to “soft”!)
Visual indicator
(depending
on the model).
Unscrew cap.
- Press and hold together
- Programs LEDs will indicate the water hardness setting.
- Press the
- Wait 30 seconds (control panel switches off) or press
Salt indicator on the control panelSalt indicator on the salt reservoir cap
Programs
button to increase setting (when the level reaches 7, the next key press will set the level back to 1).
is...
Water hardness
level
The indicator lamp lights up when SALT
NEEDS TO BE ADDED.
CANCEL/Off
and
2.
...enter this value on your
dishwasher
Add salt
min. 0.8 kg/max. 1 kg
buttons for minimum 3 seconds.
Start/Resume
3 first PROGRAM LEDs
lit on the panel
(see table of programs)
P1P2P3
(never add detergent!)
button to save setting.
(see description below in step 1 “Daily check”).
Suggestions for detergent use
Gel or Powder
(rinse aid and salt)
go to step 1
(see “Daily
check”)
Daily check
Screw on the cap.
Salt residual
around the cap
need to be
removed. Some
salt reservoir have
a level indicator
integrated in the
cap (see below
how to check).
green: OK.
Ta bl e ts
if water is
HARD extra
salt needs to
be added
(go to step 1
“Daily check”)
clear: NEEDS TO
BE ADDED
GB
-3-
Adding rinse aid
(not necessary when you use tablets). How to adjust the rinse aid dosage regulator
Daily check
Visual
2
Check the rinse aid indicator to check the
level into the dispenser.
Only use rinse aids recommended for use in domestic dishwashers.
a fault function of the appliance.
If there are streaks: reduce the dosage by turning the dial to a lower setting (1-3). If crockery is not perfectly dry: increase the dosage by turning the dial to a higher setting (5-6).
Plastic dishes have more difficulty drying and a higher rinse aid setting will not improve the situation.
Detergents with rinse aid incorporated may be effective only with longer programs. In the case of shorter programs, detergent residue may be a problem (if necessary, use powder
detergent). Detergents with rinse aid incorporated tend to form excess suds.
Adding detergent -
(press the dedicated button).
Use only detergent specifically for dishwashers in accordance with the supplier’s recommendations
Open the cover A
3
indicator
If required,
open the
cover B
(press the
dedicated
button).
rinse
Add
aid
to the
max. line
~150 ml
(depending on the model)
Rinse aid indicator on the control panelRinse aid indicator on the dispenser
The indicator lamp lights up when
RINSE AID NEEDS TO BE ADDED.
Immediately
Insert detergent:
Only fill the
detergent
dispenser prior to
starting a wash
program.
wipe away any rinse aid spilt accidentally. This prevents the formation of excess suds which can cause
Tablet / powder / liquid
into the big chamber.
The rinse aid dosage can be
adjusted to the detergent
used. The lower the setting,
the less rinse aid is dispensed
(factory setting: position 4).
Press the button to open the
cover B. Using a coin or
similar object, turn the arrow
to the desired setting. After
adjusting the rinse aid setting,
shut the cover again.
dark: OK.clear: NEEDS TO BE ADDED
Shut the cover
by pressing dedicated ribs.
Use only one tablet per one cycle,
only placed in detergent
dispenser.
All types of tablets can be used,
but for 2 in 1 type adding of salt is
mandatory.
Daily use
GB
-4-
Loading...
+ 8 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.