Whirlpool 8318507 User Manual

Installation

Instructions

Part No. 8318507

Important: Read and save these instructions.

120-volt, 60-Hz

Washer

Important:

• Installer: Leave Installation Instructions with the

homeowner.

• Homeowner: Keep Installation Instructions for future

reference.

• Save Installation Instructions for local electrical inspector’s

use.

•

Home Appliances

2-3

5-8

120 60

Table of Contents

Introduction

Pages 2 - 3

Requirements

Page 4

Installation steps

Pages 5 - 8

Parts supplied for installation

Tools needed

for installation

Location

of washer

Introduction.

A. level B. wrench C. utility knife

D. pliers E. scissors

A. 1 drain hose B. 2 inlet hoses C. 1 yellow clamp D. 2 drain hose clamps E. 2 front leveling legs

with nuts

F. 4 flat water hose

washers G. 1 hose extension H. literature package

Important: Observe all governing codes and ordinances.

Check location where washer will be installed. Make sure you

have everything necessary for correct installation. Proper installation is your responsibility.

Water heater: Set to deliver 60°C (140°F) water to washer. Earthed electrical outlet (A) is required within 152 cm

(5 feet) of upper left corner of washer cabinet. See “Electrical requirements,” Page 4.

Hot and cold water faucets (B): Must be within 122 cm (4 feet) of the upper right corner of the washer cabinet and provide water pressure 34.5-689.6 kPa (5-100 psi).

Remove parts from packages. Check that all parts were included.

The hot and cold water inlets on the back of the washer have

3/4 — 11-1/2 American hose coupling standard threads.

Level floor (C): Maximum slope under entire

washer — 2.5 cm

(1 inch).

Support (D): Floor must be sturdy enough to support washer weight (with water) of 143 kilograms (315 pounds).

The minimum and maximum motor rotation per minute (R.P.M.) is 1140-1725 R.P.M. The minimum and maximum basket R.P.M. is 423-640 R.P.M.

Do Not store or operate washer below 0°C (32°F) (some water may remain in washer).

See Use & Care Guide for “Winterizing” information.

Your safety and the safety of

others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety messages.

WARNING

This is the safety alert symbol. This symbol alerts you to potential hazards that

can kill or hurt you and others.

All safety messages will be preceded by the safety alert symbol and the word “DANGER” or “WARNING”. These words mean:

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can happen if the instructions are not followed.

You can be killed or seriously injured if you don’t immediately

follow instructions.

You can be killed or seriously injured if you don’t follow instructions.

DANGER

A. B. C.

D. E.

A. 1 B. 2 C. 1 D. 2

E. 2 F. 4 G. 1 H.

(A) 152

(B) 122

34.5-689.6

3/4 11-1/2

(C)

2.5

(D) 143

1140-1725 /

423-640 /

Front view (door not shown)

Side view

The installation dimensions shown are the minimum spaces allowable. Additional spacing should be considered for ease of installation and servicing.

If closet door is installed, the minimum air openings in top and bottom of door are required. Louvered doors with air openings in top and bottom are acceptable.

Companion appliance spacing should be considered. * Additional clearances for wall, door and floor moldings may be

required.

Front view

Untape and open washer lid. Remove packages and hoses from washer. Follow directions for your type of drain system.

If a longer drain hose is needed, use drain hose extension kit (Part No. 285702). If drain hose must be shortened, use drain hose kit (Part No. 285442).

All kits are available from Whirlpool-authorized parts distributors.

Laundry tub drain system:

Needs a 76-liter (20-gallon) laundry tub. Top of tub must be at least 86 cm (34 inches) high and no higher

than 183 cm (72 inches) from bottom of washer (A).

Standpipe drain system:

Needs a 5-cm (2-inch) minimum diameter standpipe with minimum carry-away capacity of 64 liters (17 gallons) per minute. A 5-cm (2-inch) diameter to 2.5-cm (1-inch) diameter standpipe adapter, Part No. 3363920 must be used with 2.5-cm (1-inch) diameter drain system.

Floor standpipe drain:

Top of standpipe (C) must be at least 99 cm (39 inches) high and no higher than 183 cm (72 inches) from bottom of washer.

Floor drain system:

Requires a siphon break, Part No. 285320 (B). Siphon break must be above high-water level in washer, at least 71 cm (28 inches) from bottom of washer. Additional drain hose will be needed.

Wall standpipe drain:

Top of standpipe (D) must be at least 99 cm (39 inches)high and no higher than 183 cm (72 inches) from bottom of washer.

285702

285442

(A)

86 183

64 2.5 5

2.5 3363920

285320 (B)

(

99 183

Recessed area

or closet

Drain system

closet door

7.6 cm (3")

155 cm

(24 in2)

310 cm

(48 in2)

*0 cm (*0")

43.2 cm (17")

closet door

310 cm

(48 in2)

35.6 cm max. (14" max.)

10.2 cm (4") min.

155 cm

(24 in2)

2.5 cm min. (1" min.)

+ 6 hidden pages