Whirlpool AFE 910/H, CCH 220, AFG 511/H, AFG 512-C/H SILVER, AFG 510/H/1 PROGRAM CHART
...
42015aGB.fm5 Page 1 Sunday, January 2, 2000 3:11 PM
1
2
4
Controls
1
1 2 3
PRODUCT SHEET
1. Lid handle.
2. Lock.
3. Seal.
5
4. Defrost water drain plug
(depending on model).
5. Control panel.
3
6. Basket (depending on model).
6
1. Thermostat: Temperature adjustment.
2. Red LED: Indicates that the freezer
temperature is not sufficiently low.
3. Green led: Illuminates when the appliance
is on.
4. Yellow LED: Indicates that the fast freeze
function is active.
5. Fast freeze button:
Press to activate the fast freeze function.
GB
1 2 3 4 5
The exact configuration of the controls may vary according to the model.
Notes:
For correct operation of the appliance and to allow the lid to open freely without damage,
leave at least 7 cm clearance at the sides and rear.
After installation, wait for at least two hours without moving the appliance before connecting
it to the power supply; this will enable the refrigerant circuit to reach optimum efficiency.
If the freezer is left empty for short periods, it is preferable not to switch it off.
Frost formation on the upper edges and interior walls of the appliance is a natural
phenomenon and will not affect the performance of the freezer.
GB
DF
NL
P
E
GR
I
42015aGB.fm5 Page 2 Sunday, January 2, 2000 3:11 PM
PRODUCT SHEET
Switching on the freezer for the first time
•
It is advisable to set the thermostat to a middle position on the thermostat scale (factory set
position).
•
Plug in the appliance.
•
The green LED will illuminate.
•
The red LED will also light up since the temperature inside the freezer is not yet sufficiently low for
food storage. The red LED will normally switch off within the first six hours after the appliance is
switched on.
•
Only place food inside the freezer once the red LED has switched off.
•
It will prove difficult to open the lid immediately after closing it because the hermetic seal means
there is a partial vacuum inside the freezer. Wait a few minutes before re-opening the lid.
After connecting the appliance to the mains, once the right temperature has been reached
(about an hour), ensure that the fast freeze function is inactive (yellow LED is off).
Freezer compartment temperature adjustment
To adjust the compartment temperature, proceed as follows:
•
Turn the thermostat knob
•
Turn the thermostat knob
•
When the freezer is only partially filled, it is advisable to set the thermostat to lower positions
(towards position “E”, if indicated on the thermostat scale).
①
to position 1 to set the
①
to position 6 / to set the
highest (least cold)
lowest (coldest)
storage temperature.
storage temperature.
Energy saving tips
•
Do not install the appliance in places exposed to direct sunlight or near heat sources, since this
would lead to increased energy consumption.
•
Do not obstruct the ventilation grille or the air circulation apertures.
•
Remove accumulated dust from the rear of the appliance at least once a year.
•
Use the thermostat to select the ideal storage temperature.
•
Do not place hot food in the refrigerator.
•
Restrict the number of times you open the lid.
•
Make sure the ice layer does not build up to more than 5-6 mm thick.
Changing the lid light bulb
•
Unplug the appliance.
•
Remove the diffuser by following the sequence
of steps shown in the figure.
•
Unscrew the light bulb and replace it with an
identical bulb of the same wattage and voltage.
•
Refit the diffuser and plug in the appliance.
2
1
3
5019 100 42015/A
GB
DF
NL
P
E
GR
I
Printed in Italy 01/00
Loading...