Whirlpool 20FB-L4/A+ Installation guide

INSTALLATION INSTRUCTIONS - INSTALLATIONSANLEITUNG -INSTRUCTIONSPOURLʼINSTALLATION-AANWIJZINGEN VOOR

DE INSTALLATIE

-ISTRUZIONIPERLʼINSTALLAZIONE-

INSTRUCCIONES PARA LA INSTALACIÓN

-INSTRUÇÕESDEINSTALAÇÃO-

ΟΔΗΓΙΕΣ ΕΓΚΑΤΑΣΤΑΣΗΣ

-INSTALLATIONSANV

ISNINGAR -

ASENNUSOHJEET

-INSTALLATIONSVEJLEDNING-

ИНСТРУКЦИИ ПО УСТАНОВКЕ

-MONTERINGSANVISNING-

POKYNY NA I

-ИНСТРУКЦИИЗАИНСТАЛИРАНЕ-

NÁVOD K INSTALACI

-INSTRUKCJEINSTALOWANIA-

ÜZEMBE HELYEZÉSI ÚTMUTATÓ

INSTRUCŢIUNI DE INSTALARE -

INSTALLATIONSANLEITUNG

-INSTRUCTIONSPOURLʼINSTALLATION-

AANWIJZINGEN VOOR DE INSTALLATIE

-ISTRUZIONIPERLʼINSTALLAZIONE-

NSTRUCCIONES PARA LA INSTALACIÓN

-INSTRUÇÕESDEINSTALAÇÃO-

ΟΔΗΓΙΕΣ ΕΓΚΑΤΑΣΤΑΣΗΣ

-INSTALLATIONSANVISNINGAR-

ASE

For correct and safe installation of the appliance, please carefully read this manual and the other documentation provided (see section "Precautions and general advice").

Specifications, technical data, images and parts supplied may be subject to change without prior notice.

WATER CONNECTION Disconnect the appliance from the mains power supply before starting operations.

• In any case, make sure to comply with the current local regulations regarding connection to the water system.

• The appliance is supplied with a water tube, 1.8 m long, already attached to the back of the product.

• The water tube complies with IEC 61770.

• Remove the shipping tape from the gray coiled water tubing on the rear of the appliance.

• Connect the transition connector (1) to the household water supply (2).

• Open the water tap and check for and eliminate any leaks.

• The appliance does not require adjustments or a water drain.

ELECTRICAL CONNECTION

Connect the appliance to the mains power supply. Electrical safety of the appliance can only be guaranteed if it is correctly connected to an efficient, approved earthing system.

POSITIONING AND LEVELLING YOUR REFRIGERATOR

If the appliance seems unsteady or you want the doors to close more easily, adjust the appliance's tilt following the instructions below (depending on the model, as shown in the figures on the right). The refrigerator has two front and two rear wheels at the base of the product on each side and two adjustable feet at the front (see figure A).

1. Check the installation location to be sure you have at least 1 cm clearance on all sides including the top.

2. Connect the appliance to the mains power supply.

3. Move the refrigerator into its final position.

4. Open both doors and remove the plinth to locate the feet and levelling bolts at the left and right of the refrigerator base (where present). The top bolt (1) will adjust the rear wheel (if provided), and the bottom bolt (2) will adjust the front wheel (see figure B).

5. Use the wrench provided (if present) to adjust the levelling bolts. Turn clockwise to raise the appliance, or anticlockwise to lower it. It may take several turns of the

levelling bolts and/or feet to adjust the tilt of the refrigerator.

6. After levelling the product, ensure that both feet touch the ground for safe use.

Note: do not unscrew the levelling bolts and feet too much as they could fall out.

Aligning the doors

If, after switching on the appliance and adjusting the refrigerator and freezer doors, the doors are misaligned, disconnect the appliance from the power supply and adjust both doors as indicated in the diagram at the end of this manual.

INSTALLING CUSTOM DOOR PANELS

• Installing customized panels

If you wish to install customized panels, they must be made according to the dimension drawings.

• Flat panels

Flat panels of max. thickness 6.35 mm can be fitted in the frames. Thinner panels are not recommended.

• Raised panels

A raised panel design can be created by screwing or gluing wood panels to 6.35 mm backing or by using 16 mm stock with 6.35 mm routed edges. To allow room for fingers, it is advisable to arrange the raised panels at a distance of 5.70 cm from the rear edge of the handle.

• Weight requirements for raised inserts

- The refrigerator compartment door panel must not exceed 10 kg.

- Freezer compartment door panels must not exceed a total weight of 7 kg.

INSTALLATION DIMENSIONS AND REQUIREMENTS (G) REMOVING THE FREEZER DOOR (A) REMOVING THE REFRIGERATOR DOOR (B) INSTALLING CUSTOM DOOR PANEL S (H ) MOUNTING THE FREEZER DOOR (C) MOUNTING THE REFRIGERATOR DOOR (D) HORIZONTAL ALIGNMENT OF FREEZER AND REFRIGERATOR DOORS (E) VERTICAL ALIGNMENT OF FREEZER AND REFRIGERATOR DOORS (F)

+ 5 hidden pages