Whelen SAK47 User Manual

1/4 - 20 X 1-1/4" HEX HEAD SS
9/16 FLATWASHER
1/4" SPLIT LOCKWASHER
1/4 - 20 X 1-1/2" HEX HEAD SS
®
wire exit & drain hole
A
A
SA315 / Rear View
1/4 - 20 X 1-1/4" HEX HEAD SS
9/16 FLATWASHER
1/4" SPLIT LOCKWASHER
1/4 - 20 X 1-1/2" HEX HEAD SS
®
ENGINEERING COMPANY INC.
wire exit & drain hole
A
A
SA315 / Rear View
51 Winthrop Road,
Chester, Connecticut 06412-0684
Phone: (860) 526-9504
Fax: (860) 526-4078
Installation Guide:
SA315 Siren Speaker Mounting Bracket
for 2011 to 2012 Dodge Ram 1500
Internet: www.whelen.com Sales e-mail: autosale@whelen.com Canadian Sales e-mail: canadiansales@whelen.com Customer Service e-mail: custserv@whelen.com
Installation 2011 - 2012 Ram 1500:
First, mount the speaker to the bracket. The SA315 is shipped with two 1/4-20 X 1-1/4” Hex Head Screws (A) (Figs. 1 & 2). A short screw must be used in the hole that does not bracket so it will properly secure the driver to the housing. The longer screws included in the mounting kit are necessary to go through the mounting bracket, the siren housing and into the siren driver. If for any reason you need to remove all 4 screws at once be sure to hold the driver
Sirens produce extremely loud emergency warning tones! Exposure to these tones without
DANGER!
proper and adequate hearing protection, could cause ear damage and/or hearing loss! The Occupational Safety & Health Administration (www.osha.gov) provides information necessary to determine safe exposure times in Occupational Noise Exposure Section 1910.95. Until you have determined the safe exposure times for your specific application, operators and anyone else in the immediate vicinity should be required to wear an approved hearing protection device. FAILURE TO FOLLOW THIS RECOMMENDATION COULD CAUSE HEARING LOSS!
Automotive: Sirens & Switches
©2013 Whelen Engineering Company Inc. Form No.14668 (012113)
go through the
For warranty information regarding this product, visit www.whelen.com/warranty
securely in place. IMPORTANT: For drainage purposes, the speaker must be oriented so that the wire passage hole is in the “6 o’clock” position (closest to the road).This is also the drain hole for the siren. Improper mounting will result in premature driver failure and void the product warranty.
Automotive: Sirens & Switches
Installation Guide:
SA315 Siren Speaker Mounting Bracket
ENGINEERING COMPANY INC.
51 Winthrop Road,
Chester, Connecticut 06412-0684
Phone: (860) 526-9504
Fax: (860) 526-4078
Installation 2011 - 2012 Ram 1500:
First, mount the speaker to the bracket. The SA315 is shipped with two 1/4-20 X 1-1/4” Hex Head Screws (A) (Figs. 1 & 2). A short screw must be used in the hole that does not bracket so it will properly secure the driver to the housing. The longer screws included in the mounting kit are necessary to go through the mounting bracket, the siren housing and into the siren driver. If for any reason you need to remove all 4 screws at once be sure to hold the driver
Sirens produce extremely loud emergency warning tones! Exposure to these tones without
DANGER!
proper and adequate hearing protection, could cause ear damage and/or hearing loss! The Occupational Safety & Health Administration (www.osha.gov) provides information necessary to determine safe exposure times in Occupational Noise Exposure Section 1910.95. Until you have determined the safe exposure times for your specific application, operators and anyone else in the immediate vicinity should be required to wear an approved hearing protection device. FAILURE TO FOLLOW THIS RECOMMENDATION COULD CAUSE HEARING LOSS!
©2013 Whelen Engineering Company Inc. Form No.14668 (01213)
go through the
For warranty information regarding this product, visit www.whelen.com/warranty
Page 1
securely in place. IMPORTANT: For drainage purposes, the speaker must be oriented so that the wire passage hole is in the “6 o’clock” position (closest to the road).This is also the drain hole for the siren. Improper mounting will result in premature driver failure and void the product warranty.
for 2011 to 2012 Dodge Ram 1500
Internet: www.whelen.com Sales e-mail: autosale@whelen.com Canadian Sales e-mail: canadiansales@whelen.com Customer Service e-mail: custserv@whelen.com
B
U
M
P
E
R
Tow Hook
ADD WASHERS
This bracket mounts to either the left or right side front of the
Tow Hook
B
U
M
P
E
R
Tow Hook
ADD WASHERS
Tow Hook
vehicle near the bumper using 3 existing studs where the tow hook mounts to the frame (Fig. 3).
1. Remove the 3 nuts holding the tow hook in. Save the nuts for re-mounting the bracket (Fig. 3).
2. Mount the bracket to the vehicle by re-installing two of the vehicles nuts, adding the 4 supplied 9/16 flatwashers as shown in figure 4. Also, be sure to insert the third mounting stud into the top hole in the bracket.
3. Re-install the third nut to the stud coming through the top of the bracket securing the bracket to the vehicle (Fig. 5). NOTE: Figures 4 & 5 show the bracket
without the speaker for illustrative purposes. The speaker should be mounted before installing the bracket.
4. Extend the WHITE (positive) and BLACK (negative) speaker wires to your siren amplifier and refer to the amplifiers instructions for connections
This bracket mounts to either the left or right side front of the vehicle near the bumper using 3 existing studs where the tow hook mounts to the frame (Fig. 3).
1. Remove the 3 nuts holding the tow hook in. Save the nuts for re-mounting the bracket (Fig. 3).
2. Mount the bracket to the vehicle by re-installing two of the vehicles nuts, adding the 4 supplied 9/16 flatwashers as shown in figure 4. Also, be sure to insert the third mounting stud into the top hole in the bracket.
3. Re-install the third nut to the stud coming through the top of the bracket securing the bracket to the vehicle (Fig. 5). NOTE: Figures 4 & 5 show the bracket
without the speaker for illustrative purposes. The speaker should be mounted before installing the bracket.
4. Extend the WHITE (positive) and BLACK (negative) speaker wires to your siren
Page 2
amplifier and refer to the amplifiers instructions for connections
Loading...