Whelen SAK25 User Manual

®

ENGINEERING COMPANY INC.

51 Winthrop Road,

Chester, Connecticut 06412-0684

Phone: [phone]

Fax: [phone]

Installation:

IMPORTANT: Read all warnings before starting installation.

1. This bracket mounts above the radiator. Remove the front fascia
to gain access to the radiator (see manufacturers instructions).

2. Place the bracket onto the mounting area in its exact mounting
location. Mark the location of the 3 mounting holes onto the
mounting surface.

3. Secure the speaker to the bracket with the supplied hardware.

IMPORTANT: The SA315 is supplied with 3 long bolts (1/4-20 X 1­1/2” Hex Head SS). The long bolts must go through the bracket.

The short bolt (already installed on the speaker) must be

1/4" SPLIT
LOCK WASHER

1/4 - 20 X 1-1/2"
HEX HEAD SS

1/4 X 20 X 1-1/4

HEX HEAD

1/4" SPLIT

LOCK WASHER

used in the hole that does not go
through the bracket. The short bolt
secures driver to speaker body.

4. Secure the speaker/
bracket to the vehicle. with the supplied 1/4 X 3/4 Hex washer head self-tapping mounting screws.
Drive the mounting screws in only part way with the drill and socket.

WARNING: You must drive the self-tapping screws in until they are tightened almost all the way,
then finish tightening by hand. If you drill them all the way in, they will strip the hole. Tighten the
screws the rest of the way with a hand wrench being careful not to strip the holes.

5. Extend the WHITE (positive) and BLACK (negative) wires to your amplifier. Refer to the amplifiers

instructions for connections.

Installation Guide:

SA315 Speaker Mounting bracket

2006 Chevrolet Express

Internet: www.whelen.com
Sales e-mail: [e-mail]
Canadian Sales e-mail: [e-mail]
Customer Service e-mail: [e-mail]

Fig. 1

Automotive: Sirens & Switches

©2007 Whelen Engineering Company Inc.
Form No.14111A (050708)

For warranty information regarding this product, visit www.whelen.com/warranty

ENGINEERING COMPANY INC.

51 Winthrop Road,

Chester, Connecticut 06412-0684

Phone: [phone]

Fax: [phone]

Installation:

IMPORTANT: Read all warnings before starting installation.

1. This bracket mounts above the radiator. Remove the front fascia
to gain access to the radiator (see manufacturers instructions).

2. Place the bracket onto the mounting area in its exact mounting
location. Mark the location of the 3 mounting holes onto the
mounting surface.

3. Secure the speaker to the bracket with the supplied hardware.

IMPORTANT: The SA315 is supplied with 3 long bolts (1/4-20 X 1­1/2” Hex Head SS). The long bolts must

The short bolt (already installed on the speaker) must be

1/4" SPLIT
LOCK WASHER

1/4 - 20 X 1-1/2"
HEX HEAD SS

1/4 X 20 X 1-1/4

HEX HEAD

1/4" SPLIT

LOCK WASHER

used in the hole that does not go
through the bracket. The short bolt
secures driver to speaker body.

go through the bracket.

4. Secure the speaker/
bracket to the vehicle. with the supplied 1/4 X 3/4 Hex washer head self-tapping mounting screws.
Drive the mounting screws in only part way with the drill and socket.

WARNING: You must drive the self-tapping screws in until they are tightened almost all the way,
then finish tightening by hand. If you drill them all the way in, they will strip the hole. Tighten the
screws the rest of the way with a hand wrench being careful not to strip the holes.

5. Extend the WHITE (positive) and BLACK (negative) wires to your amplifier. Refer to the amplifiers

instructions for connections.

®

Installation Guide:

SA315 Speaker Mounting bracket

2006 Chevrolet Express

Internet: www.whelen.com
Sales e-mail: [e-mail]
Canadian Sales e-mail: [e-mail]
Customer Service e-mail: [e-mail]

Fig. 1

Automotive: Sirens & Switches

©2007 Whelen Engineering Company Inc.
Form No.14111A (050708)

For warranty information regarding this product, visit www.whelen.com/warranty

Page 1

SA315

WARNING: For drainage
purposes, the speaker box’s wire
passage hole (which is also the
siren drain hole) must be located
in the “6 o’clock” (closer to the
road) position for proper
mounting. Improper mounting
will not only result in driver
failure, but will also void the
product warranty.

DRAIN
HOLE

IMPORTANT! It is the responsibility of the installation technician to make sure that the installation and operation of this product will not

interfere with or compromise the operation or efficiency of any vehicle equipment! Before returning the vehicle to active service,
visually confirm the proper operation of this product, as well as all vehicle components and equipment.

DAN G E R! Sirens produces extremely loud emergency warning tones! Exposure to these tones without proper and adequate hearing

protection, could cause ear damage and/or hearing loss! The Occupational Safety & Health Administration (www.osha.gov) provides
information necessary to determine safe exposure times in Occupational Noise Exposure Section 1910.95. Until you have determined the safe
exposure times for your specific application, operators and anyone else in the immediate vicinity should be required to wear an approved
hearing protection device. FAILURE TO FOLLOW THIS RECOMMENDATION COULD CAUSE HEARING LOSS!

ACTIVATION OF THIS
SIREN MAY DAMAGE
UNPROTECTED EARS!

CAUTION

Loud siren noise can cause

Wear

Protection!

hearing damage and/or loss.

Refer to OSHA Section 1910.95 prior
to putting ANY siren into service!

SA315

WARNING: For drainage
purposes, the speaker box’s wire
passage hole (which is also the
siren drain hole) must be located
in the “6 o’clock” (closer to the
road) position for proper
mounting. Improper mounting
will not only result in driver
failure, but will also void the
product warranty.

DRAIN
HOLE

IMPORTANT! It is the responsibility of the installation technician to make sure that the installation and operation of this product will not

interfere with or compromise the operation or efficiency of any vehicle equipment! Before returning the vehicle to active service,
visually confirm the proper operation of this product, as well as all vehicle components and equipment.

DAN G E R! Sirens produces extremely loud emergency warning tones! Exposure to these tones without proper and adequate hearing

protection, could cause ear damage and/or hearing loss! The Occupational Safety & Health Administration (www.osha.gov) provides
information necessary to determine safe exposure times in Occupational Noise Exposure Section 1910.95. Until you have determined the safe
exposure times for your specific application, operators and anyone else in the immediate vicinity should be required to wear an approved
hearing protection device. FAILURE TO FOLLOW THIS RECOMMENDATION COULD CAUSE HEARING LOSS!

ACTIVATION OF THIS
SIREN MAY DAMAGE
UNPROTECTED EARS!

CAUTION

Loud siren noise can cause

Wear

Protection!

hearing damage and/or loss.

Refer to OSHA Section 1910.95 prior
to putting ANY siren into service!

Page 2