PIONEERS IN SAFETY SIGNALS
®
PIONEERS IN SAFETY SIGNALS
®
PIONEERS IN SAFETY SIGNALS
®
ENGINEERING COMPANY, INC.
51 WINTHROP ROAD
CHESTER, CONNECTICUT 06412-0684
TELEPHONE: (860) 526-9504
FAX: (860) 526-4078
GASKET
INDEX NOTCHES
LOCATED INSIDE
REFLECTOR AND ON
LAMP SOCKET
LAMP
REPLACEMENT...
WARNING!
ATTEMPT TO REPLACE THE LAMP WITH FINGERS...
USE THE LAMP REPLACEMENT TOOL INCLUDED IN KIT.
The lamp assembly is packed with the lamp replacement tool
protecting the glass tube.
1. In some cases, the reflector may have to be removed for
lamp replacement. If the lamp does not easily exit reflector,
remove the reflector and check for obstructions.
Make sure gasket on lamp assembly is in place. Route the
2.
wire assembly through the reflector, and follow procedures
as outlined in steps 6 and 7 on the other side of this page in
lamp replacement instruction text.
TO AVOID PERSONAL INJURY,
FIT WINGS ON THE
REMOVING TOOL OVER
WINGS ON LAMP SOCKET
REMOVING
TOOL
HALOGEN
TUBE
STROBE TUBE
DO NOT
ENGINEERING COMPANY, INC.
51 WINTHROP ROAD
CHESTER, CONNECTICUT 06412-0684
TELEPHONE: (860) 526-9504
FAX: (860) 526-4078
INDEX NOTCHES
LOCATED INSIDE
REFLECTOR AND ON
LAMP SOCKET
LAMP
GASKET
FIT WINGS ON THE
REMOVING TOOL OVER
WINGS ON LAMP SOCKET
REMOVING
TOOL
HALOGEN
TUBE
STROBE TUBE
REPLACEMENT...
WARNING!
ATTEMPT TO REPLACE THE LAMP WITH FINGERS...
USE THE LAMP REPLACEMENT TOOL INCLUDED IN KIT.
The lamp assembly is packed with the lamp replacement tool
protecting the glass tube.
In some cases, the reflector may have to be removed for
1.
lamp replacement. If the lamp does not easily exit reflector,
remove the reflector and check for obstructions.
Make sure gasket on lamp assembly is in place. Route the
2.
wire assembly through the reflector, and follow procedures
as outlined in steps 6 and 7 on the other side of this page in
lamp replacement instruction text.
TO AVOID PERSONAL INJURY,
DO NOT
ENGINEERING COMPANY, INC.
51 WINTHROP ROAD
CHESTER, CONNECTICUT 06412-0684
TELEPHONE: (860) 526-9504
FAX: (860) 526-4078
ROUTE 145, WINTHROP ROAD
INDEX NOTCHES
LOCATED INSIDE
REFLECTOR AND ON
LAMP SOCKET
LAMP
GASKET
FIT WINGS ON THE
REMOVING TOOL OVER
WINGS ON LAMP SOCKET
REMOVING
TOOL
HALOGEN
TUBE
STROBE TUBE
REPLACEMENT...
WARNING!
ATTEMPT TO REPLACE THE LAMP WITH FINGERS...
USE THE LAMP REPLACEMENT TOOL INCLUDED IN KIT.
The lamp assembly is packed with the lamp replacement tool
protecting the glass tube.
1. In some cases, the reflector may have to be removed for
lamp replacement. If the lamp does not easily exit reflector,
remove the reflector and check for obstructions.
Make sure gasket on lamp assembly is in place. Route the
2.
wire assembly through the reflector, and follow procedures
as outlined in steps 6 and 7 on the other side of this page in
lamp replacement instruction text.
TO AVOID PERSONAL INJURY,
DO NOT
IMPORTANT WARNING FOR
SYSTEMS FEATURING STROBE
LAMP HOLDER ASSEMBLIES!!!
THE STROBE LIGHT POWER SUPPLY IS A HIGH VOLT-
AGE DEVICE. DO NOT REMOVE STROBE LAMP
HOLDER ASSEMBLY OR DISMANTLE STROBE LIGHT
HEAD ASSEMBLY WHILE SYSTEM IS IN OPERATION.
WAIT 10 MINUTES AFTER TURNING OFF POWER
BEFORE STARTING WORK OR TROUBLE
SHOOTING OF THE SYSTEM.
© Whelen Engineering Company Inc.
Form No. 13339A (062598)
ANY
IMPORTANT WARNING FOR
SYSTEMS FEATURING STROBE
LAMP HOLDER ASSEMBLIES!!!
THE STROBE LIGHT POWER SUPPLY IS A HIGH VOLT-
AGE DEVICE. DO NOT REMOVE STROBE LAMP
HOLDER ASSEMBLY OR DISMANTLE STROBE LIGHT
HEAD ASSEMBLY WHILE SYSTEM IS IN OPERATION.
WAIT 10 MINUTES AFTER TURNING OFF POWER
BEFORE STARTING ANY WORK OR TROUBLE
SHOOTING OF THE SYSTEM.
© Whelen Engineering Company Inc.
Form No. 13339A (062598)
IMPORTANT WARNING FOR
SYSTEMS FEATURING STROBE
LAMP HOLDER ASSEMBLIES!!!
THE STROBE LIGHT POWER SUPPLY IS A HIGH VOLT-
AGE DEVICE. DO NOT REMOVE STROBE LAMP
HOLDER ASSEMBLY OR DISMANTLE STROBE LIGHT
HEAD ASSEMBLY WHILE SYSTEM IS IN OPERATION.
WAIT 10 MINUTES AFTER TURNING OFF POWER
BEFORE STARTING ANY WORK OR TROUBLE
SHOOTING OF THE SYSTEM.
© Whelen Engineering Company Inc.
Form No. 13339A (062598)
HALOGEN AND STROBE
HALOGEN AND STROBE
HALOGEN AND STROBE
ASSEMBLY INSTALLATION
AND REPLACEMENT
INSTRUCTIONS.
WARNING! TO AVOID PERSONAL INJURY,
DO NOT ATTEMPT TO REPLACE THE LAMP
WITH FINGERS... USE THE LAMP
REPLACEMENT TOOL INCLUDED IN KIT.
1. Switch light system in the off mode.
2. Expose lamp by removing polycarbonate lens.
3. Place the lamp removing tool over the lamp. The
wings on the tool should fit over the wings on the lamp
holder assembly.
4. Twist the removing tool 1/8 turn counter-clockwise.
Remove the burned out lamp from reflector and
disconnect from the power cable or cable harness.
IMPORTANT NOTE!!! When replacing lamp holder
assemblies in a unit with more than one light head
assembly, it is important to replace them one at a
time. If more than one lamp is removed from the
unit without being replaced, the connectors on the
cable harness, lamp assemblies are connected to,
will shift and will be inaccessible...
5. If the reflector is dirty, use this opportunity to clean
gently with a soft cloth or tissue moistened with
isopropyl alcohol. Do not scrub, or use abrasive
cleaners. If reflector is blemished, replace it to keep
light output intensity at a high level.
ASSEMBLY INSTALLATION
AND REPLACEMENT
INSTRUCTIONS.
WARNING! TO AVOID PERSONAL INJURY,
DO NOT ATTEMPT TO REPLACE THE LAMP
WITH FINGERS... USE THE LAMP
REPLACEMENT TOOL INCLUDED IN KIT.
1. Switch light system in the off mode.
2. Expose lamp by removing polycarbonate lens.
3. Place the lamp removing tool over the lamp. The
wings on the tool should fit over the wings on the lamp
holder assembly.
4. Twist the removing tool 1/8 turn counter-clockwise.
Remove the burned out lamp from reflector and
disconnect from the power cable or cable harness.
IMPORTANT NOTE!!! When replacing lamp holder
assemblies in a unit with more than one light head
assembly, it is important to replace them one at a
time. If more than one lamp is removed from the
unit without being replaced, the connectors on the
cable harness, lamp assemblies are connected to,
will shift and will be inaccessible...
5. If the reflector is dirty, use this opportunity to clean
gently with a soft cloth or tissue moistened with
isopropyl alcohol. Do not scrub, or use abrasive
cleaners. If reflector is blemished, replace it to keep
light output intensity at a high level.
ASSEMBLY INSTALLATION
AND REPLACEMENT
INSTRUCTIONS.
WARNING! TO AVOID PERSONAL INJURY,
DO NOT ATTEMPT TO REPLACE THE LAMP
WITH FINGERS... USE THE LAMP
REPLACEMENT TOOL INCLUDED IN KIT.
1. Switch light system in the off mode.
2. Expose lamp by removing polycarbonate lens.
3. Place the lamp removing tool over the lamp. The
wings on the tool should fit over the wings on the lamp
holder assembly.
4. Twist the removing tool 1/8 turn counter-clockwise.
Remove the burned out lamp from reflector and
disconnect from the power cable or cable harness.
IMPORTANT NOTE!!! When replacing lamp holder
assemblies in a unit with more than one light head
assembly, it is important to replace them one at a
time. If more than one lamp is removed from the
unit without being replaced, the connectors on the
cable harness, lamp assemblies are connected to,
will shift and will be inaccessible...
5. If the reflector is dirty, use this opportunity to clean
gently with a soft cloth or tissue moistened with
isopropyl alcohol. Do not scrub, or use abrasive
cleaners. If reflector is blemished, replace it to keep
light output intensity at a high level.
6. Connect the new lamp to the power cable or cable
harness, and line up the index notches on bulb socket
and the index notches inside the reflector. Know that
the lamp socket goes in one way only. Twist 1/8 turn
clock wise.
7. Lamp tubes may be held and touched with the
finger without any harm to the lamp tube. However
wipe any finger prints from the glass bulb with a soft
cloth or tissue. Reinstall polycarbonate lens.
6. Connect the new lamp to the power cable or cable
harness, and line up the index notches on bulb socket
and the index notches inside the reflector. Know that
the lamp socket goes in one way only. Twist 1/8 turn
clock wise.
7. Lamp tubes may be held and touched with the
finger without any harm to the lamp tube. However
wipe any finger prints from the glass bulb with a soft
cloth or tissue. Reinstall polycarbonate lens.
6. Connect the new lamp to the power cable or cable
harness, and line up the index notches on bulb socket
and the index notches inside the reflector. Know that
the lamp socket goes in one way only. Twist 1/8 turn
clock wise.
7. Lamp tubes may be held and touched with the
finger without any harm to the lamp tube. However
wipe any finger prints from the glass bulb with a soft
cloth or tissue. Reinstall polycarbonate lens.