Whelen RBKT1 User Manual
®
ENGINEERING COMPANY INC.
51 Winthrop Road,
Chester, Connecticut 06412-0684
Phone: (860) 526-9504
Fax: (860) 526-4078
Installation:
This bracket can mount to many different vehicles. This manual will
cover mounting to a Ford Crown Victoria.
1. Open the hood and find the mounting area located just in front of the
vehicles horns as shown in Fig. 1. NOTE: While not essential,
removing the vehicle grill (following vehicle manufacturers
instructions) will make the installation easier. Place the bracket
onto the mounting surface in the exact mounting location. Mark off
(onto the mounting surface) the location of the mounting holes, then
remove the bracket and drill the mounting holes with an
appropriately sized drill for the hardware.
2. Secure the lighthead to the bracket as
shown on the next page.
3. Secure the bracket to the vehicle using the
supplied mounting hardware.
4. Extend the lighthead wires to your power
source and refer to the lighthead manual
for wiring.
Installation Guide:
TIR3™ Lighthead Mounting Bracket
Model RBKT1, RBKT2
Internet: www.whelen.com
Sales e-mail: autosale@whelen.com
Canadian Sales e-mail: autocan@whelen.com
Customer Service e-mail: custserv@whelen.com
INSTALL
HERE
Fig. 1
NOTE: Model RBKT1 (single bracket) is
shown for example. Model RBKT2 (double
bracket), mounts the same way.
Automotive: Lightheads
©2004 Whelen Engineering Company
Inc. Form No.13927A (062807)
ENGINEERING COMPANY INC.
51 Winthrop Road,
Chester, Connecticut 06412-0684
Phone: (860) 526-9504
Fax: (860) 526-4078
Installation:
This bracket can mount to many different vehicles. This manual will
cover mounting to a Ford Crown Victoria.
1. Open the hood and find the mounting area located just in front of the
vehicles horns as shown in Fig. 1. NOTE: While not essential,
removing the vehicle grill (following vehicle manufacturers
instructions) will make the installation easier. Place the bracket
onto the mounting surface in the exact mounting location. Mark off
(onto the mounting surface) the location of the mounting holes, then
remove the bracket and drill the mounting holes with an
appropriately sized drill for the hardware.
2. Secure the lighthead to the bracket as
shown on the next page.
3. Secure the bracket to the vehicle using the
supplied mounting hardware.
4. Extend the lighthead wires to your power
source and refer to the lighthead manual
for wiring.
For warranty information regarding this product, visit www.whelen.com/warranty
®
Installation Guide:
TIR3™ Lighthead Mounting Bracket
Model RBKT1, RBKT2
Internet: www.whelen.com
Sales e-mail: autosale@whelen.com
Canadian Sales e-mail: autocan@whelen.com
Customer Service e-mail: custserv@whelen.com
INSTALL
HERE
Fig. 1
NOTE: Model RBKT1 (single bracket) is
shown for example. Model RBKT2 (double
bracket), mounts the same way.
Automotive: Lightheads
©2004 Whelen Engineering Company
Inc. Form No.13927A (062807)
Page 1
For warranty information regarding this product, visit www.whelen.com/warranty
MOUNTING
GASKET
8 - 32 X 1" PPH MS SS
MODEL RBKT1
TIR3™ SUPER-LED® Lighthead
shown for reference
FLANGE
6 - 32 X 3/8"
PPH MS SS
8-32
WHIZ
NUT
MODEL RBKT2
TIR3™ SUPER-LED® Lighthead
shown for reference
FLANGE
6 - 32 X 3/8"
PPH MS SS
MOUNTING
GASKET
8-32X1"PPHMSSS
MODEL RBKT1
8-32
WHIZ
NUT
MODEL RBKT2
Page 2
Loading...