Whelen 70509 User Manual

®
ENGINEERING COMPANY INC.
Route 145, Winthrop Road, Chester, Connecticut 06412 Phone: (860) 526-9504 Fax: (860) 526-2009 Internet: www.whelen.com Sales/Service e-mail: aviation@whelen.com
Installation Guide
Model 70509 Flasher
INSTALLATION PROCEDURES
The following inform ation is to assist you i n installing a Whelen flashing anti-collision light system.
EQUIPMENT LIMITATIONS
The Model 70509 Flasher meets the requirements of FAR 23.1401 and 25.1401. “If certification for night operations is requested, the airplane must have an anti-collision light system that consists of one or more approved anti-collision lights located so that their light will not impair the flight crew members vision or detract from the conspicuity of the position lights.”
OPERATING INSTRUCTIONS
14V INPUT VOLTAGE14V UNIT INPUT CURRENT(LAMP ON)2.7 AMPS
INPUT CURRENT(AVERAGE)1.3 AMPS
28V INPUT VOLTAGE 28V UNIT INPUT CURRENT(LAMP ON)1.3 AMPS
INPUT CURRENT(AVERAGE).65 AMPS
FLASH RATE 50 ±5 FPM LAMP 35W HALOGEN
Aviation
DUTY CYCLE 50%
Model 70509 Flasher
TSO-C96A Approved
1. Choose an appropriat e M odel 70 509 fla shing anti­collision light assembly (14V or 28V) which is applicable to your aircraft.
2. The installation procedure described in the following text will be confined to a single light installation, but is identical for multiple light installation if requi red .
3. Remove old anti-collision light and flasher assembly. Locate and save existing applicable +14VDC or +28VDC lead and (-) ground lead. Clean and prep lead ends as required.
4. Connect existing +14VDC or +28 VDC lead to the (red or white) lead on the light assembly and connect existing (-) g round l ead to th e (blac k) lea d on the light assembly. Both leads must be connected by an approved aircraft connection.
5. Breaker Requirements 14VDC
System - Make sure existing system is equipped with a maximum 5 amp breaker for one light and a maximum 10 amp breaker for a two light system.
System - Make sure existing system is
28VDC equipped with a maximum 2.5 amp breaker for one light and a maximum 5 amp breaker for a two light system.
6. Install light assembly and insure that all leads are clear of any obstructions. Secure light assembly, use lock washers and/or thread locker on all threaded fasteners.
7. Check all avionics systems for interference from this installation.
8. When necessary, waterproof the flasher base assembly to aircraft. Apply single part silicone (RTV) or equivalent around any open area where water could get in.
9. Update aircraft records and complete Form 337.
10. Obtain FAA field approval for installation.
©1997 Whelen Engineering Company Inc. Form No.13215C (041202)
Page 1
MODEL 70509 REPLACEMENT PARTS
DESCRIPTIONITEM
1
14V FLASHER ASSY. (RED) 14V FLASHER ASSY. (WHITE)
2
14V FLASHER ASSY. (RED / WHITE)
3
28V FLASHER ASSY. (RED)
4
28V FLASHER ASSY. (WHITE)
5
28V FLASHER ASSY. (RED / WHITE)
6 7
LENS ASSY. (RED) 68-2170504-50
8
LENS ASSY. (WHITE) 68-2170504-30
9
LENS ASSY. (RED/WHITE) 68-2170504-60 14V FLASHER ASSY. (RED) W/HOLE
10
14V FLASHER ASSY. (WHITE) W/HOLE
11
14V FLASHER ASSY. (RED / WHITE) W/HOLE
12
28V FLASHER ASSY. (RED) W/HOLE
13
28V FLASHER ASSY. (WHITE) W/HOLE
14
28V FLASHER ASSY. (RED / WHITE) W/HOLE
15
LENS ASSY. (RED) W/HOLE
16
LENS ASSY. (WHITE) W/HOLE
17
LENS ASSY. (RED/WHITE) W/HOLE
18
CLAMP RING 250
19
#6-32 X ½ PHILLIPS PHMS
20
GASKET
21
LAMP ASSY. 14V
22
FLASHER BASE ASSY. 14V
23
FLASHER BASE ASSY. 28V
24
LAMP ASSY. 28V
25
#6-32 X 5/16 S.S. HEX NUT
26
ø
PART NUMBER
01-0770509-00 01-0770509-01 01-0770509-02 01-0770509-03 01-0770509-04 01-0770509-05
01-0770509-10 01-0770509-11 01-0770509-12 01-0770509-13 01-0770509-14 01-0770509-15
68-2170504-58 68-2170504-38 68-2170504-68
19-262353-000 14-0050503-30
38-0230840-00 02-0350433-00
02-0250627-00
02-0250627-01
02-0350433-01
13-0050513-64
LENS
ASSEMBLY
7
16
17
CLAMP
RING
19
21
ASSEMBLY
98
18
26
20
LAMP
22 25
3.70
6.00±.50
2.58
MODEL 70509
DIMENSIONS
Page 2
810
FLASHERS /
MOUNTING BASE
ASSEMBLY
(+28V) WHITE
(14V) RED
BLACK (-)
LABEL
(REF)
}
Loading...