Whelen 3PC0C0CD User Manual
ENGINEERING COMPANY INC.
51 Winthrop Road,
Chester, Connecticut 06412-0684
Phone: (860) 526-9504
Fax: (860) 526-4078
®
Installation Guide:
PAR-36 Super-LED® Work Light
Internet: www.whelen.com
Sales e-mail: autosale@whelen.com
Canadian Sales e-mail: autocan@whelen.com
Customer Service e-mail: custserv@whelen.com
Automotive: Lightheads
Installation:
1. Drill a 3/8” mounting hole and insert the mounting bolt
through the hinge bracket and into the mounting hole.
2. Secure the hinge bracket with the supplied elastic stop nut
and flat washer.
3. Extend the wires to your power source (6, 9 or 12 LED
White or Red: +12VDC Black: Ground). Fuse the power
wire at 3 amps.
WARNING! All customer supplied wires that connect to the
positive terminal of the battery must be sized to supply at
least 125% of the maximum operating current and FUSED
the battery to carry that load. DO NOT USE CIRCUIT
BREAKERS WITH THIS PRODUCT!
Caution: Permanent mounting of this product will require
drilling. It is absolutely necessary to make sure that no other
vehicle components could be damaged by this process.
Check both sides of the mounting surface before starting. If
damage is likely, select a different mounting location.
CAUTION! DO NOT LOOK DIRECTLY AT THESE LEDS WHILE THEY ARE ON.
MOMENTARY BLINDNESS AND/OR EYE DAMAGE COULD RESULT!
©2008 Whelen Engineering Company Inc.
Form No.14165 (011008)
IMPORTANT WARNING!
For warranty information regarding this product, visit www.whelen.com/warranty
at
IMPORTANT! It is the
responsibility of the
installation technician to
make sure that the
installation and operation
of this product will not
interfere with or
compromise the operation
or efficiency of any vehicle
equipment! Before
returning the vehicle to
active service, visually
confirm the proper
operation of this product,
as well as all vehicle
components/equipment.
3/8-16
ELASTIC
STOP NUT
3/8"
FLAT
WASHER
3/8-16
X 1-3/4"
CARRIAGE
BOLT
3/8" FLAT
WASHER
3/8-16 X 2-1/4
HEX HEAD
HINGE
BRACKET
MOUNTING
SURFACE
STOP NUT
PAR 36
BOLT
3/8-16
ELASTIC
Automotive: Lightheads
®
ENGINEERING COMPANY INC.
51 Winthrop Road,
Chester, Connecticut 06412-0684
Phone: (860) 526-9504
Fax: (860) 526-4078
Installation:
1. Drill a 3/8” mounting hole and insert the mounting bolt
through the hinge bracket and into the mounting hole.
2. Secure the hinge bracket with the supplied elastic stop nut
and flat washer.
3. Extend the wires to your power source (6, 9 or 12 LED
White or Red: +12VDC Black: Ground). Fuse the power
wire at 3 amps.
WARNING! All customer supplied wires that connect to the
positive terminal of the battery must be sized to supply at
least 125% of the maximum operating current and FUSED
the battery to carry that load. DO NOT USE CIRCUIT
BREAKERS WITH THIS PRODUCT!
Caution: Permanent mounting of this product will require
drilling. It is absolutely necessary to make sure that no other
vehicle components could be damaged by this process.
Check both sides of the mounting surface before starting. If
damage is likely, select a different mounting location.
CAUTION! DO NOT LOOK DIRECTLY AT THESE LEDS WHILE THEY ARE ON.
MOMENTARY BLINDNESS AND/OR EYE DAMAGE COULD RESULT!
©2008 Whelen Engineering Company Inc.
Form No.14165 (011008)
IMPORTANT WARNING!
For warranty information regarding this product, visit www.whelen.com/warranty
Page 1
at
Installation Guide:
PAR-36 Super-LED® Work Light
Internet: www.whelen.com
Sales e-mail: autosale@whelen.com
Canadian Sales e-mail: autocan@whelen.com
Customer Service e-mail: custserv@whelen.com
IMPORTANT! It is the
responsibility of the
installation technician to
make sure that the
installation and operation
of this product will not
interfere with or
compromise the operation
or efficiency of any vehicle
equipment! Before
returning the vehicle to
active service, visually
confirm the proper
operation of this product,
as well as all vehicle
components/equipment.
3/8-16
ELASTIC
STOP NUT
3/8"
FLAT
WASHER
3/8-16
X 1-3/4"
CARRIAGE
BOLT
3/8" FLAT
WASHER
HINGE
BRACKET
MOUNTING
PAR 36
3/8-16 X 2-1/4
HEX HEAD
BOLT
SURFACE
3/8-16
ELASTIC
STOP NUT
Loading...