wheelock UTA-WH-VPS INSTALLATION INSTRUCTIONS

273 Branchport Avenue
Long Branch, NJ 07740 Thank you for using our products.
[phone]
www.wheelockinc.com

UNIVERSAL TELEPHONE ALERT WITH STROBE

Use this product according to this instruction manual. Please keep this instruction manual for future reference.

MODEL: UTA-WH

A 115 VAC LINE CORD IS REQUIRED FOR STROBE AND PIEZO ACTIVATION.

INSTALLATION INSTRUCTIONS

NOTE: THIS UNIT REQUIRES TWO SEPARATE VOLTAGE INPUTS TO OPERATE: 115VAC, 60Hz AND AN INPUT VOLTAGE
LISTED IN TABLE 5 TO TRIGGER THE RINGING CIRCUIT.

GENERAL INFORMATION:

The UTA-WH has a loud attention getting electronic ringer designed for use in noisy locations or for wide area coverage. It is FCC
Part 68 and IC CS-03 Registered for the public telephone network and can be used behind PBX and key systems that use interrupted
ring voltages from 40-130V, 20-30Hz or 20-30VDC/VAC or 36-60VDC.

The UTA-WH, when used indoors, will accommodate a modular plug that mates with an RJ-11C jack (USA) or a CA-11 jack
(Canada) for ringing voltage. The input voltage triggers the strobe and audible, which receive their operating power from the
115VAC, 60Hz source.

UTA-WH includes a high intensity flashing strobe for visual signaling and offers a choice of four selectable sound patterns (horn,
bell, single chime or vibrating chime) with a volume control. The UTA-WH is equipped with a weather resistant backbox for
optional outdoor use with conduit enclosed wiring.

APPLICATION INFORMATION:

The installation of this product must conform to the following instructions. IF ANY WORDS OR LETTERS APPEAR ON THE

PRODUCT INDICATING A PARTICULAR USE, THE PRODUCT MUST BE USED ONLY IN THE MANNER SO INDICATED.
FIELD ADJUSTMENT, REPAIR OR MODIFICATION OF THESE SIGNALS SHOULD NOT BE ATTEMPTED

. Malfunctioning units

should be returned for factory repair or replacement in accordance with Wheelock Inc.'s published terms and conditions.

NOTE

CAUTION

: All

CAUTIONS

: The installation of this equipment should only be undertaken by qualified personnel.

and

WARNINGS

are identified by the symbol . All warnings are printed in bold capital letters.

WARNING: THE UTA-WH IS NOT TO BE USED AS AN INDOOR VISUAL EVACUATION SIGNAL FOR THE HEARING

IMPAIRED.

WARNING: SHUT OFF ALL POWER BEFORE INSTALLING. ELECTRICAL SHOCK CAN CAUSE DEATH OR

SERIOUS INJURY.

FCC REGULATIONS:

• This equipment complies with Part 68 of the FCC Rules. The label affixed to this product contains, among other information, the
FCC Registration Number and the Ringer Equivalence Number (REN) for this product. This information must be provided to the
telephone company if requested.

• The REN is used to determine the quantity of appliances, which you may connect to your telephone line and still have all of those
appliances ring when your telephone number is called. In most, but not all areas, the sum of the REN's of all appliances
connected to one line should not exceed five (5.0). To be certain of the number of appliances that you may connect to your line,
contact your local telephone company.

• This equipment should not be used on coin telephone lines. Connection to party line service is subject to state tariffs.

• If trouble is experienced, disconnect this equipment from the telephone line to determine if it is causing the malfunction. If the

equipment is determined to be malfunctioning, its use shall be discontinued until the problem has been corrected.

• Should the equipment cause harm to the telephone network, the telephone company shall, if possible, notify the customer that
temporary discontinuance of service may be required; however, where prior written notice is not possible, the telephone company
may temporarily discontinue service without notice, if such action is necessary under the circumstances. The telephone company
may make changes in its communication facilities, equipment and operations procedures, where such action is reasonably
required in the operation of its business and is not inconsistent with the rules and regulations of the Federal Communications
Commission.

Copyright 2000 Wheelock, Inc. All rights reserved.

P82969 J

Sheet 1 of 1

INDUSTRY CANADA REGULATIONS: (Only applicable for use in Canada)

• NOTICE: The Industry Canada (IC) label identifies certified equipment. This certification means that the equipment meets
certain telecommunications network protective operational and safety requirements as prescribed in the appropriate Terminal
Equipment Technical requirements document(s). The Department does not guarantee the equipment will operate to the user's
satisfaction.

• Before installing this equipment, users should ensure that it is permissible to be connected to the facilities of the local
telecommunications company. The equipment must also be installed using an acceptable method of connection. The customer
should be aware that compliance with the above conditions may not prevent degradation of service in some situations.

• Repairs to certified equipment should be coordinated by a representative designated by the supplier. Any repairs or alterations
made by the user to this equipment, or equipment malfunctions, may give the telecommunications company cause to request the
user to disconnect the equipment.

• Users should ensure for their own protection, that the electrical ground connections of the power utility, telephone lines and
internal metallic water pipe system, if present, are connected together. This precaution may be particularly
Caution: Users should not attempt to make such connections themselves, but should contact the appropriate electric inspection
authority, or electrician, as appropriate.

• RINGER EQUILAVENCE NUMBER: The Ringer Equivalence Number

(REN) assigned to each terminal device provides an
indication of the maximum number of terminals allowed to be connected to a telephone interface. The termination of an interface
may consist of any combination of devices subject only to the requirement that the sum of the Ringer Equivalence Numbers of all
the devices does not exceed 5.

SPECIFICATIONS:

Table 1: Sound Output (dBA) and Current (REN) at Maximum Volume

24VDC 24VAC 48VDC 90Vrms/20Hz
Horn 109dB/2.5mA 109dB/4.0mA 109dB/3.0mA 109dB/4.5mA/.5A REN
Bell 104dB/2.5mA 104dB/4.0mA 104dB/3.0mA 104dB/4.5mA/.5A REN
Vibrating Chime 94dB/2.5mA 94dB/4.0mA 94dB/3.0mA 94dB/4.5mA/.5A REN
Single Chime 94dB/2.5mA 94dB/4.0mA 94dB/3.0mA 94dB/4.5mA/.5A REN
No Sound 2.5mA 4.0mA 3.0mA 4.5mA/.5A REN

NOTES:

1. Input Voltage Range: 24VDC = 20-30VDC, 24VAC = 20-30VAC, 48VDC = 36-60VDC, 90Vrms =40-130Vrms, 20-30Hz

2. For 24VDC, 24VAC, and 48VDC inputs, add 10% more input current when operating the unit at maximum input voltage. For
90Vrms inputs, add 40% more input current when operating the unit at maximum input voltage

3. dBA is measured on-axis in a non-reflective (free field) test room using fast meter response.

Table 2: Sound Output Volume Adjusting Range

Horn 109-82dB
Bell 104-76dB
Vibrating Chime 94-68dB
Single Chime 94-68dB

Table 3: Tone Description

Horn Broadband Horn
Bell 1560Hz Modulated (0.07 Sec. ON/Repeat
Vibrating Chime 700Hz (1.0 Sec. Decay/Repeat)
Single Chime 700Hz (1.0 Sec. Decay)

Table 4: Duty and Ring Cycle

Cycle 90Vrms/20-30Hz 24VDC/AC, 48VDC
Duty Cycle 33% Max. 100% Max.
Min. Ring Cycle ON Time 0.8 Sec. 0.8 Sec.
Min. Ring Cycle OFF Time 1.6 Sec. 0.8 Sec.
Max. Ring Cycle ON Time 10 Sec. Continues

Strobe Flash Rate: Nominal 1 Flash Minimum/Ring Cycle

Strobe Output: 15cd on axis.

AC Current: 0.150 Amps Max.

P82969 J

Sheet 2 of 2