Congratulations and thank you for choosing our oven.
We are sure you will find it a pleasure to use. Before you
use the oven, we recommend that you read through
the relevant sections of this manual, which provides a
description of your appliance and its functions.
To avoid the risks that are always present when you use
an appliance, it is important that the appliance is installed
correctly and that you read the safety instructions
carefully to avoid misuse and hazards.
We recommend that you keep this instruction booklet for
future reference and pass it on to any future owners.
After unpacking the appliance, please check it is not
damaged. If in doubt, do not use the appliance but
contact your local customer care centre.
This appliance complies with requirements of Australian
Standard AS/NZS 60335.2.6.
Conditions of use
This appliance is intended to be used in household
and similar applications such as:
• Staff kitchen areas in shops, offices and other
working environments
• Farm houses
• By clients in hotels, motels and other residential
type environments
• Bed and breakfast type environments
Please ensure you read the instruction manual fully
before you call for service, or a full service fee could
be applicable.
Important safety instructions ........................................................3
Installing your appliance ..................................................................5
IMPORTANT INFORMATION THAT MAY
IMPACT YOUR MANUFACTURER’S WARRANTY
Adherence to the directions for use in this manual
is extremely important for health and safety.
Failure to strictly adhere to the requirements in
this manual may result in personal injury, property
damage and affect your ability to make a claim
under the Westinghouse manufacturer’s warranty
provided with your product. Products must be
used, installed and operated in accordance with
this manual. You may not be able to claim on the
Westinghouse manufacturer’s warranty in the
event that your product fault is due to failure to
adhere to this manual.
IMPORTANT
This symbol indicates tips and information about use
of the appliance.
ENVIRONMENT
This symbol indicates tips and information about
economical and ecological use of the appliance.
2CONTENTS
TIPS & INFORMATION
WARNING
IMPORTANT SAFETY INSTRUCTIONS
Please read the user manual carefully and store in a handy
place for later reference.
IMPORTANT
Important – check for any damages or marks.
• If you find the oven is damaged or marked, you
must report it within 7 days if you wish to claim for
damage/marks under the manufacturer’s warranty.
This does not affect your statutory rights.
• Discolouration of the enamel has no effect on the
performance of the appliance.
ENVIRONMENT
Information on disposal for users
• Most of the packing materials are recyclable. Please
dispose of those materials through your local
recycling depot or by placing them in appropriate
collection containers.
• If you wish to discard this product, please contact
your local authorities and ask for the correct method
of disposal.
WARNING
These warnings have been provided in the interest of
safety. You MUST read them carefully before installing or
using the appliance.
• An authorised person must install this appliance and
carry out servicing. (Certificate of Compliance to
be retained)
• Before using the appliance, ensure that all packing
materials are removed from the appliance.
• Always be careful when you move the appliance
because it is heavy. Always wear safety gloves.
• Do not pull the appliance by the door handle.
• This appliance must be earthed.
• In order to avoid any potential hazard, the enclosed
installation instructions must be followed.
• Ensure that all specified vents, openings and air
spaces are not blocked.
• Do not modify this appliance.
• This appliance must not be used as a space heater.
• Where the appliance is built into a cabinet, the
cabinet material must be capable of withstanding
70°C. If adjacent to vinyl wrapped surfaces, use
installation kit from vinyl wrap supplier.
• Ensure the appliance is switched off before cleaning
or replacing parts. This can be done by switching off
the appliance via the powerpoint or isolating switch
(if available), or the switchboard.
• Do not use steam cleaners, as this may cause
moisture build up.
• Switch the appliance off before removing the oven
light glass for globe replacement.
• Do not open the oven door during steam cooking.
Steam can be released. There is a risk of skin burns.
There is a risk that steam causes moisture damage to
cabinets.
• Allow the oven to cool down for 30 minutes before you
drain the water tank in a steam oven. Scalding water
may be released.
• Always keep the appliance clean. Ensure fats and oils do
not accumulate around elements, burners or fans.
• Care must be taken when wiping exposed stainless
steel edges.…they can be sharp!
• Do not spray flammable materials in or under the
appliance, e.g. aerosols.
• Do not leave the grill on unattended.
• Always turn the grill off immediately after use as fat left
behind may catch fire.
• Do not cover the grill insert with foil, as fat left there
may catch fire.
• Always keep the oven dish, grill dish and bake trays
clean as any fat residue may catch fire.
• To avoid an accident, ensure that the oven shelves
and fittings are always inserted into the appliance in
accordance with the instructions.
• The door glass on this appliance is made from a tough,
durable material that withstands heating and cooling
without breaking. As a precaution however, do not put
cold water on hot glass.
• Door glass that is damaged should be
immediately replaced.
• This appliance is not intended for use by persons
(including children) with reduced physical, sensory
or mental capabilities, or lack of experience and
knowledge, unless they have been given supervision or
instruction concerning use of the appliance by a person
responsible for their safety.
• Children should be supervised to ensure that they do
not play with the appliance.
• Accessible parts will become hot when in use. To avoid
burns and scalds, children should be kept away.
• During use, this appliance becomes hot. Care should
be taken to avoid touching hot surfaces, e.g. oven door,
heating elements or internal surfaces of
the oven.
• Always use gloves when handling hot items inside
the oven.
• To maintain safe operation, it is recommended that the
product be inspected every 5 years by an authorised
service person.
• New appliances can have an odour during the first
operation. It is recommended to ‘run in’ the oven before
you cook. Run the oven(s) at 180°C for 30 minutes and
ensure the room is well ventilated.
• This appliance must not be installed behind a decorative
door.
• The cooking process has to be supervised. A short term
cooking process has to be supervised continuously.
3IMPORTANT SAFETY INSTRUCTIONS
IMPORTANT SAFETY INSTRUCTIONS
WARNING
Cooktop only
• If the ceramic glass on cooktop is accidently cracked,
switch off the appliance to avoid the possibility of
electric shock.
• Unattended cooking on a hob with fat or oil can be
dangerous and may result in a fire.
CAUTION
Read the following carefully to avoid damage to
the appliance.
• The grill door must be left fully open whilst grilling in
a separate grill wall oven and a separate grill
underbench oven.
• The grill tray must be fully inserted whilst grilling.
• Do not place thick portions of food under the grill.
Foods may curl, catch and ignite.
• Do not use the door as a shelf.
• Do not push down on the open oven door.
• Do not use harsh abrasive cleaners or metal scrapers
to clean the oven door glass since they can scratch
the surface which may result in shattering of the
glass.
• Do not use harsh abrasive cleaners, powder cleaners,
steel wool or wax polishes on enamel.
• Do not use sharp metal implements or utensils on any
surface, as these may leave permanent scratches or
marks.
• Do not use stainless steel cleaners, abrasive cleaners
or harsh solvents to clean your stainless steel
appliance.
• Do not line the bottom of the oven or grill with foil or
cookware, it will damage the enamel.
• Do not use the base of the oven for cooking – it will
damage the enamel.
• Do not put water directly into the hot appliance.
• Always clean the appliance immediately after any
food spills.
Cooktop only
• Do not allow pots to boil dry as damage to both pan
and cooktop may result.
• Do not operate the cooktop for an extended period
of time without a utensil on the hot plate.
• Do not allow large cookware to overhand onto the
adjacent benchtop. This will cause scorching to the
benchtop surface.
• Do not place heat resistant mats, wire mats or
aluminium foil under pots or pans.
• Do not cook food directly on the ceramic glass
surface.
• Do not use round bottom woks, wok stands or similar
utensils that could lead to overheating of hotplates
and possible damage to the cooking surface.
• Do not operate this appliance by means of an
external timer or separate remote control system.
• Danger of fire: Do not store items on cooking
surfaces.
NOTE: You must read these warnings carefully before
installing or using the appliance. If you need assistance,
contact your Customer Care Centre. The manufacturer will
not accept liability, should these instructions or any other
safety instructions incorporated in this book be ignored.
4IMPORTANT SAFETY INSTRUCTIONS
WARNING
WARNING
INSTALLING YOUR APPLIANCE
WARNING
To avoid any potential hazard, you must follow our
instructions when you install your appliance. Failure
to install the appliance correctly could invalidate any
warranty or liability claims and lead to prosecution.
• This appliance must be installed by an authorised
person according to all codes and regulations as
stated in the local municipal building code and other
relevant statutory regulations.
• Wiring connections must be in accordance with AS/
NZS 3000 Wiring Rules and any particular conditions
of the local authority.
• Refer to data plate for rating information. The data
plate is positioned behind the bottom of the oven
door.
• Disconnection in the fixed wiring must occur in
accordance with the AS/NZS3000 wiring rules.
• Wiring should be protected against mechanical
failure. Refer to AS/NZS3000 clauses 3.3.2.6, 3.9, 3.10
• A means of disconnection with a contact separation
of at least 3mm must be supplied in the fixed wiring.
• This range must be connected with cable of 75°C
rating minimum.
• This product has passed the insulation resistance test
after manufacture. If the resistance reading is low at
installation, it is probably caused by moisture from
the atmosphere being absorbed by the elements
after the range has been produced. (Pass at 0.01MΩ
AS/NZS 3000 Wiring Rules Clause 8.3.6.2).
Rated power input
MODELTOTAL kWA1 kWA2 kW
WVE6458.72.36.4
WARNING
This appliance must be properly earthed.
• Do not lift the appliance by the door handles.
• Prepare the cupboard opening to match your
appliance measurements. (See diagrams)
• Slide appliance into the cupboard, ensuring that the
supply cable (where fitted) does not kink.
• To prevent tipping, use the screws supplied to secure
your oven into the cupboard. Use just 2 screws for
underbench and separate grill underbench ovens, and
4 screws for separate grill wall ovens. Remove the
bottom door in separate grill wall ovens to provide
access to the bottom 2 screwing points.
• For appliances fitted with a flexible supply cord, if
the cord is damaged, it must be replaced by the
manufacturer or its service agent or similarly qualified
person in order to avoid a hazard. The plug must be
accessible after installation.
• Where the appliance is built into a cabinet, the
cabinet material must be capable of withstanding
70°C. Installation into low temperature tolerant
cabinetry (e.g. vinyl coated) may result in
deterioration of the low temperature coating by
discolouring or bubbling.
• If the appliance is installed adjacent to vinyl-wrapped
surfaces, use an installation kit available from the
vinyl-wrap supplier.
• Electrolux Home Products cannot accept
responsibility for damage caused by installation into
low temperature tolerant cabinets.
• After installation, test and ensure that the appliance
operates correctly before handing it over to the
customer. It is recommended that this product is not
installed in an unvented living space, particularly if
that space incorporates sleeping quarters.
MODEL
WVE613597 x 596 x 56916A2.3kW9.6A2.5
WVES613597 x 596 x 56916A2.3kW9.6A2.5
WVE614597 x 596 x 56916A2.3kW9.6A2.5
WVE615597 x 596 x 56916A3.3kW13.8A2.5
WVE615SCA/DSCA597 x 596 x 56916A3.1kW12.9A2.5
WVE616597 x 596 x 56916A3.0kW12.7A2.5
WVEP615597 x 596 x 57316A3.1kW12.9A2.5
WVE617597 x 596 x 56916A3.3kW13.8A2.5
WVEP617597 x 596 x 57316A3.3kW13.8A2.5
WVEP618597 x 596 x 57316A3.1kW12.9A2.5
WVE625890 x 596 x 56925A5.3kW22.1A4.0
WVE6361083 x 596 x 56932A6.2kW25.8A6.0
WVE645597 x 596 x 56940A8.7kW36.1A6.0
WVE655727 x 596 x 56925A4.9kW20.4A4.0
WVE665890 x 596 x 56925A5.3kW22.1A4.0
WVEP627890 x 596 x 57325A5.3kW22.1A4.0
Note: Electrical connection is 230-240 volts AC 50Hz. Wiring minimum temperature rating 75°C.
PRODUCT DIMENSIONS
(H X W X D) MM
MIN FUSE
RATING
MAX POWER
RATING
MAX CURRENT
RATING
WIRE SECTION
(MM)
5INSTALLING YOUR APPLIANCE
WARNING
INSTALLING YOUR APPLIANCE (CONTINUED)
• If a powerpoint is fitted it must be accessible with the
appliance installed, as the plug must be accessible
after installation.
• This appliance must be mounted on a flat surface for
the full width and depth of the product.
• To avoid overheating, the appliance must not
be installed in a recess or cupboard behind a
decorative door.
Hard wiring detail
1. Remove terminal cover plate from rear panel
of appliance.
2. Fit wires through hole in cover plate and make
connections to terminals.
3. Engage wires into plastic clip. Secure plastic clip with
two long silver screws (supplied in separate bag).
4. Replace cover plate onto rear panel.
553mm
15mm
8mm min
clearance
Cabinet construction for your appliance
For the best integration within a kitchen, install the
appliance in a standard 600mm wide cupboard that gives
a flush fit with the surrounding cupboard fronts as shown
in Fig. A. A recess of 20 mm is ideal.
With the exception of pyrolytic ovens, the appliance can
also be installed using a proud fit to the surrounding
cupboard as shown in Fig. B.
CAUTION
For all Pyrolytic clean oven models, the oven must be
installed as a flush fit to the surrounding cupboards and
the “Infill panel” MUST not exceed 100mm in length. This
ensures a 16mm gap is maintained between the cabinet
and oven side to prevent the cupboard overheating.
Fig. A
Flush Fit
16mm
Infill
panel
568mm
100mm max
for Pyro
oven
20mm
Cupboard
door
Fig. B
A
Proud Fit
Cupboard
door
Second active wire only
required (optional) for
multi-phase products
Plastic clips
Levelling oven
Place a level in the oven as below, making sure the level
sits on the front and rear forms.
16mm
Oven
Infill
panel
Oven
600mm
568mm
600mm
100mm max
oven
for Pyro
6INSTALLING YOUR APPLIANCE
Plastic clip
securing points
✓
Non-pyrolytic underbench ovens and side open door oven
WARNING
Your underbench oven looks best when the control panel is directly under the benchtop. An upper infill panel may have
to be added if the cooktop placed over the oven is too deep. Refer to cooktop installation instructions for required
clearance between cooktop and oven.
upper infill
(if required)
ABC
Flush fit600600581min
Proud fit565590560min
A
B
558
C
mounting
holes
use black
installation
screws supplied
596
Pyrolytic underbench oven
Your underbench oven looks best when the control panel is directly under the benchtop. An upper infill panel may have
to be added if the cooktop placed over the oven is too deep. Refer to cooktop installation instructions for required
clearance between cooktop and oven.
Power point connection for the WVEP618 must be accessible with the appliance fully installed. If the supply cord is
damaged it must be replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid
a hazard.
CAUTION
NOTE: Dimension “D”.
A requirement for all pyrolytic clean ovens – for proper ventilation there must be a gap at the bottom rear of the
cabinet. This can be a full width opening 20mm deep.
upper infill
(if required)
GAS TYPE
Flush fit600600581min20
Proud fit565590560min20
A
B
D
C
558
ABCD
use black
installation
screws supplied
mounting
holes
596
7INSTALLING YOUR APPLIANCE
WARNING
INSTALLING YOUR APPLIANCE (CONTINUED)
Separate grill underbench oven
Your underbench oven looks best when the control panel is directly under the benchtop. An upper infill panel may have
to be added if the cooktop placed over the oven is too deep. Refer to cooktop installation instructions for required
clearance between cooktop and oven.
NOTE TO INSTALLER: For separate grill underbench installations where a cooktop is installed directly above the
appliance, a minimum clearance distance of 10mm must be allowed for between the bottom of the cooktop & the top
of the separate grill underbench oven.
C
ABC
Flush fit600731581min
Proud fit565723560min
A
B
561
use black
installation
screws supplied
mounting
holes
use black
installation
screws supplied
Separate grill wall oven & duo oven
CAUTION
NOTE: Dimension “D”.
A requirement for all separate grill wall ovens and all duo ovens – for proper ventilation there must be a gap at the
bottom rear of the cabinet. This can be a full width opening 20mm deep.
ABCD
Flush fit600893581min20
Proud fit565885560min20
650mm
min
561
A
B
D
C
596
use black
installation
screws supplied
mounting
holes
use black
installation
screws supplied
8INSTALLING YOUR APPLIANCE
Double oven
WARNING
450mm
min.
GAS TYPE
ABC
Flush fit6001086581min
Proud fit5651078560min
561
use black installation
A
B
C
596
screws supplied
mounting
holes
use black installation
screws supplied
Combo oven – cooktop cut-out dimensions
A minimum gap of 40mm must be maintained between
the top of the underbench oven and the bottom of the
cooktop to ensure adequate ventilation and space for
the interconnection lead.
The cooktop must be installed above the
underbench oven.
COOKTOP DIMENSIONS
Overall Cooktop Dimensions
Width610mm
Depth515mm
Depth of base45mm
COOKTOP CUT-OUT DIMENSIONS
AB
Cooktop560mm490mm
A minimum gap of 40mm must be maintained between
the top of the underbench oven and the bottom of the
cooktop to ensure adequate ventilation and space for
the interconnection lead.
CAUTION
The cooktop MUST be installed above the underbench
oven.
9INSTALLING YOUR APPLIANCE
PRODUCT DESCRIPTION
WVE613/WVES613/WVES614
WVE615
15623
2134
WVEP615
13
1
Function selector
2
Oven/grill indicator light
3
Oven/grill temperature selector
10PRODUCT DESCRIPTION
4
‘Auto-off’ timer
5
Function indicator light
6
Electronic Clock
WVE616
WVE617
WVEP617
1
1
5623
5263
WVEP618
1
Function selector
2
Oven/grill indicator light
3
Oven/grill temperature selector
4
‘Auto-off’ timer
1
ON/OFF
FUNCTION TEMP
Hold 3s
BACK FAVOURITE
SET TIME
3
ALARM OK
78
5
Function indicator light
6
Electronic Clock
7
Programmable controller
8
Water drawer
11PRODUCT DESCRIPTION
PRODUCT DESCRIPTION (CONTINUED)
FUNCTIONTEMP
Hold 3s
BACKFAVOURITE
SET TIME
ALARMOK
ON/OFF
WVE615SCA/DSCA
101162
WVE625
WVEP627
WVE636
2231
689
1398
12
1
Upper function selector
2
Oven/grill indicator light
3
Upper oven/grill temperature selector
4
‘Auto-off’ timer
PRODUCT DESCRIPTION
3126289
5
Function indicator light
6
Electronic Clock
7
Programmable controller
8
Lower function selector
9
Lower oven/grill temperature selector
10
Function selector
11
Temperature selector
WVE645
WVE655
1011121314154
WVE665
1716618
25
161725186
1
Upper function selector
2
Oven/grill indicator light
3
Upper oven/grill temperature selector
4
‘Auto-off’ timer
5
Grill indicator light
6
Electronic Clock
7
Programmable controller
8
Lower function selector
9
Lower oven/grill temperature selector
10
Bottom left hob full and half
on/off/temperature
11
Top left hob on/off/temperature
12
Top right hob on/off/temperature
13
Bottom right hob on/off/temperature
14
Oven/grill function selector
15
Oven/grill temperature selector
16
Oven function selector
17
Oven temperature selector
18
Grill function/temperature selector
13PRODUCT DESCRIPTION
WARNING
BEFORE FIRST USE
Preparing your appliance for the first time
• Please remove all internal boxes and bags from the
oven before operation.
• Please wipe out the oven interior prior to operation
with warm soapy water and polish dry with a soft
clean cloth. Do not close the oven door until the oven
is completely dry.
• If your appliance is fitted with a mechanical “Auto
Off” timer, make sure it is set to “Off” marker for
manual operation.
CAUTION
• Do not line the oven with foil as it will damage the
enamel.
• New appliances can have an odour during first use. It
is recommended to ‘run in’ the oven before cooking
for the first time. Operate the oven(s), empty, at a
temperature of 180°C for approximately 30 minutes.
For appliances with a separate grill, run the grill on
maximum for 15 minutes WITH GRILL DOOR OPEN.
Please ensure that the room is well ventilated during
this process.
WVEP615, WVEP627, WVEP617 controller
Before the appliance can be used, the time must be set.
When power is supplied to the oven, the clock icon will be
displayed. Along with the
flashing. This indicated that the “hour” portion of the time
is ready to be changed.
Toggle the temperature selector
when you have the right hour.
The minutes will flash and can be set in the same manner.
5 seconds after the last change, the clock display will stop
flashing, confirming that the time has been set.
NOTE: The clock has a 24 hour display.
clock symbol the “12” will be
or , then touch
Setting the time of day
If you have purchased a model fitted with an electronic
clock or programmable controller, you must set the time
of day before you can operate your appliance.
Electronic clock
• After the appliance has been electrically connected,
“12.00” will be displayed and the “Clock” indicator
symbol
• To set the time of day, press the
• After 5 seconds from the last change, the “Clock”
indicator symbol
time has been set.
NOTE: The clock has a 24 hour display.
will flash.
or symbols.
will disappear, confirming the
WVEP618 programmable controller
• After the appliance has been electrically connected,
press
• To set the time, press
and press OK
• Then, “Set time of day” is highlighted and press
• Press or to set the hour and press
• Press or to set the minutes and press
• Press to return to function menu
to turn ON
until “Settings” is highlighted
14BEFORE FIRST USE
1
2
3
INSTALLING YOUR OVEN ACCESSORIES
Slides (Telescopic runners)
1. Obtain left hand side rack and left hand slide – see
image to identify.
2. The shaded wires indicate the wire the slide can be
mounted on. Fit slide rear clips to the rear of wire at
an angle as shown below.
1
2
3. Push slide front clip over wire until secured
Left hand side rack
Shelves and trays
The shelves are designed so that they have maximum
extension but cannot be accidentally pulled right out.
To fit a shelf to side racks:
NOTE: To Locate the rear edge of the shelves, the detents
on the side wires should be towards the oven back wall.
See image.
1. Rest the rear edge of the shelf on the lower guide rail
of the side rack - see diagram. Ensure the same rail
positions on both sides of the oven are being engaged.
2. With the front edge raised, begin to slide the shelf in
between the guide rails of the side rack.
3. Once the detents have passed the front edge of the
side rack, the shelf can be pushed fully in.
CLICK !
Detent
Side racks
• The side racks attach to each side of your oven.
There is a left hand and right hand version (see image
below for details).
4. When fully inserted the shelf should not interfere with
the closed oven door.
• Insert the rear peg into the rear access hole provided,
ensuring that the peg is fully inserted.
• Then locate the front peg into the front access hole
and push in firmly.
• For the grill compartments on WVE626, WVE665,
and WVEP627 models, the side rack fitment is the
same as above.
Front PegRear Peg
15INSTALLING YOUR OVEN ACCESSORIES
INSTALLING YOUR OVEN ACCESSORIES (CONTINUED)
Back post
To fit a shelf or tray to telescopic slides:
1. Push the shelf or tray along the top of the slide until it
hits the back post.
Back post
2. Drop the front of the shelf or tray onto the slide
ensuring it sits behind the front post of the slide.
Front post
Air Fry (For applicable models only)
The Air Fryer can be placed onto slides or into side racks
in the same manner as an oven shelf.
3. When fully inserted the shelf/tray should not interfere
with the closed oven door.
Shelves and trays (WVE655 only)
• To insert the grill tray in a separate grill underbench
product, open the grill door and fully extend the grill
drawer. Position the grill tray so that the slots on the
outer edges fit over the tabs on the slides.
16INSTALLING YOUR OVEN ACCESSORIES
USING YOUR OVEN
Understanding your oven functions
Your oven will have a selection of the following functions.
Refer to “Description of your appliance” to confirm what
functions are available to you.
Large oven
Rapid Heat
Heat comes from the element surrounding the fan as well
as the smaller element above the food. This allows you to
preheat your oven 30% quicker than with standard “Bake”.
“Rapid heat” is ideal for cooking frozen pre-cooked foods
such as savoury pastries, pizzas, mini meals (TV dinners),
meat pies and fruit pies. Simply place the food in the oven
straight from the freezer and heat – ideal for busy people.
Air Fry
Air fry enables advanced convection cooking function
without having to turn the food, giving crispy great
tasting results in a shorter time without all the oil. This is
suitable for french fries, chicken wings, nuggets and similar
products.
Bake
Heat comes from two elements, one above and one below
the food. The bottom element is a clean heat element and
is below the floor of the oven. Both elements are controlled
by the thermostat and will turn on and off to maintain
the set temperature. You can use the “Bake” function
for a single tray of biscuits, scones, muffins, cakes, slices,
casseroles, baked puddings, roasts and delicate egg dishes.
Steam Assisted Cooking (WVEP618 model only)
Perfect for all kinds of meat, poultry and fish dishes. The
hot air ensures the outside of the food is sealed whilst
the steam keeps the inside tender. Steam comes from the
outlet pipe and heat comes from the element surrounding
the fan. This fan circulates the hot air and steam around
the oven cavity so that you can position the food
anywhere in the oven. The browning of meat or fish will
be perfect, with the best cooking result at the core. Shape
will be preserved and evenly firm. Vegetables will retain a
high level of nutrients.
NOTE: Steam will only start if the water tank has been
filled and the oven temperature is above 130°C.
Fan Forced (Fan Bake for WVEP618 model)
Heat comes from the element surrounding the fan. This
fan circulates the hot air around the oven cavity so that
you can put your food in different places in the oven
and still cook them at the same time. You can use the
“Fan Forced” function for multi-shelf cooking, reheating
cooked foods, pastries and complete oven meals. It will
cook at a lower temperature and be faster than baking.
Please note that some variation in browning is normal.
Base Heat
Heat comes from the element below the food. The
element is controlled by the thermostat and will turn on
and off to maintain the set temperature. The “Base heat”
function can be used to add extra browning to the bases
of pizzas, pies and pastries. Cook in the lower half of the
oven when you are using only one shelf. For best results,
use silver or shiny trays.
17USING YOUR OVEN
Loading...
+ 39 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.