
IK007 Integration kit
Installation manual
Refrigeration
STM3900, STM4200, SBM3800, SBM4300,
WTM2800, WTM3000, WTM3300, WTM3900,
WTM4200, WTM4400, WTM5200, WTE4200,
WTE5200, WTB2300, WTB2500, WTB2800,
WTB3400, WTB3700, WBM3700, WBM3800,
WBM4000, WBM4300, WBM5100, WBE4300,
WBE5100, WRM3700, WRM4300,WFM3000,
WFM3600, KTM2800, KTM3000, KTM3300,
KTM3600, KTM3900, KTM4200, KTM4400,
KTM5200, KBM3800, KBM4300, KBM5100,
WBB3400, WBB3700

2
CONGRATULATIONS
Congratulations and thank you for choosing our integration
kit. Before you install the integration kit, we recommend
that you read through the entire installation manual.
To avoid the risks that are always present when you install
an electrical appliance, it is important that the integration
kit and appliance is installed correctly. Please read the
safety instructions in this installation manual as well as the
appliance’s user manual to carefully to avoid misuse
and hazards.
We recommend that you keep this instruction booklet
for future reference and pass it on to any future owners.
After unpacking the integration kit, please check it is not
damaged. If in doubt, do not use the integration kit but
contact your local Electrolux Customer Care Centre.
BEFORE YOU CALL
Please ensure you read the instruction manual fully before
you call for service, or a full service fee could be applicable.
CONTENTS
3 General warnings
4 Refrigerator integration kit items
5 Cupboard dimensions
8 Installation of 120˚ hinge
9 Preparation
9 Attaching top hinge bracket
10 Attaching slide-housing to refrigerator doors
12 Placing refrigerator in cupboard
12 Refrigerator alignment
13 Securing refrigerator in cupboard
14 Attaching slide-bar to cupboard door
INFORMATION ON DISPOSAL
FOR USERS
ENVIRONMENT!
• Most of the packaging materials are recyclable.
Please dispose of these materials through your local
recycling depot or by placing them in appropriate
collection containers.
• If you wish to discard this product, please contact
your local authorities and ask for the correct method
of disposal.

GENERAL WARNINGS
Please read the user manual carefully and store in a
handy place for later reference. Pass the user manual
on to possible new owners of the appliance.
NOTE: We strongly recommend that a professional
builder/cabinetmaker builds this unit into required
cabinetry prior to finished installation in customer’s
kitchen. Electrolux cannot take responsibility for
any installation issues when customer retrofits
this product into cabinetry. Cabinet door height
built in excess of refrigerator door height will be
unsupported and risk bowing.
NOTE: Please refer to your Appliance User Manual for
warnings relating to the appliance.
SYMBOLS
IMPORTANT!
This symbol indicates tips and information about
use of the appliance.
3
ENVIRONMENT!
This symbol indicates tips and information about
economical and ecological use of the appliance.

4
120° hinge
mounting plate
120° hinge
mounting plate
120° hinge
mounting plate
120° hinge
mounting plate
REFRIGERATOR INTEGRATION KIT ITEMS
Because this kit is common to a variety of models, you
need to select the items required to suit your model. The
items required for the models covered in this instruction
booklet are shown below.
Those items not required on your particular model should
be discarded.
Item Quantity in kit Quantity required Description
Top hinge bracket
PNº 143 3129
Slide-housing
PNº 144 5132
Slide-bar
PNº 1421620
Location bracket
front footing
PNº 1444993
Note: this pa rt is to be u sed
on all models other than
WTB2300, WTB2500,
WTB2800, WTB3400 &
WTB3700.
Refrigerator
screws
PN º 741249
Two door model
Single door model
1 1 1
2 2 1
2 2 1
1 1 1
8 8 4
Cupboard screws
PNº 1449 422
120º hinge
PNº 1457832
Mounting plate
for hinge
PN º 145 8211
Self tapping
wood screws
PNº 1458212
Z bracket
IK foot location
PNº 808958001
(Used in m odels W TB2300,
WTB250 0, WTB2800,
WTB3400 & WTB3700)
12 12 8
5 5 (3+2) 3
5 5 (3+2) 3
20 20 12
1 1 0

CUPBOARD DIMENSIONS
IMPORTANT!
Pages 5, 6, 7 and 8 should be given to the person
responsible for cupboard design and construction.
The cupboard dimensions required for each model are
shown on page 6, 7 & 8.
1. All sizes are internal and measured in millimetres.
2. It is important to ensure that the correct cupboard
sizes are used to ensure adequate air flow around
the refrigerator.
3. Cupboard hinges should be a 120° opening type.
(Use hinges supplied).
4. Three hinges should be used on each cupboard
door higher than 1000mm.
5. Ensure the refrigerator is not connected to a power
supply whilst installation takes place.
6. Each operation should be carried out in the sequence
specified in this instruction sheet.
5
NOTE: All sizes are internal and in millimetres.
Dim ‘A’
Model
2 door top freezer models
WTB2300
WTB2500
WTB2800
WTM2800, KTM2800
WTM3000, KTM3000
WTM3300, KTM3300
WTB3400
KTM3600
WTB3700
WTM3900, KTM3900, STM3900
WTM4200, WTE4200, KTM4200, STM4200
WTM4400, KTM4400
WTM5200, WTE5200, KTM5200
2 door bottom freezer models
WBB3400
WBB3700
WBM3700
WBM3800, KBM3800, SBM3800
WBM4000
WBM4300, WBE4300, KBM4300, SBM4300
WBM5100, WBE5100, KBM5100
(mm)
minimum
1485
1550
1650
1640
1710
1810
1690
1730
1800
1810
1730
1810
1810
1690
1800
1660
1810
1760
1810
1810
Dim ‘B’
(mm)
680
680
680
680
680
680
715
680
715
680
740
740
740
740
740
740
680
740
740
740
Dim ‘C’
(mm)
645
645
645
700
700
700
700
795
700
795
795
795
895
745
745
745
795
745
795
895
Dim ‘D’*
(mm)
910
975
1075
1047
1117
1217
1110
1137
1220
1217
1137
1217
1217
702
702
702
702
702
702
702
Dim ‘E’
(mm)
450
450
450
500
500
500
500
600
500
600
600
600
600
600
600
600
600
600
600
600
Dim ‘G’
(mm)
270
270
270
219
219
219
298
241
298
241
241
241
278
298
298
241
241
241
278
Dim ‘H’
(mm)
250
250
250
300
300
300
300
395
300
395
395
395
495
300
300
395
395
395
395
495
Dim ‘I’*
(mm)
Please
use the
calculation
below to
measure
Dimension
‘I’ for your
specific
model.
single door models
WFM3000
WFM3600
WRM3700
WRM4300
1810
1810
1810
1810
Step 1
Measure and confirm Dimension ‘A’.
Step 2
To calculate Dimension ‘I’ use the equation below.
Dim ‘I’ = Dim ‘A’ - (Dim ‘D’ + 5mm) mm
680
680
680
680
700
795
700
795
–
–
–
–
500
600
500
600
219
241
219
241
300
395
300
395
Step 3
* Add cabinetry thickness to Dimension ‘D’ and
Dimension ‘I’ for final measurement before construction.