Westinghouse W-230 User Manual

Owner’s Manual

Guide d’utilisation Manual del Usuario

Outdoor Lighting Fixture Installation Instructions

Instructions d'installation Appareil d'éclairage pour utilisation extérieure

Instrucciones para la insalación de la lámpara para exteriores

W-230

100405

Please write model number here for future reference: / Veuillez noter le numéro de modèle aux fins de référence ultérieure: / Por favor, incluya el número del modelo aquí para futura referencia:

ASSEMBLY INSTRUCTIONS FOR OUTDOOR LIGHT FIXTURE

Congratulations on yourWestinghouse purchase. This fixture has been designed to give you many years of beauty and service. Please email questions and comments to: catalogroom@westinghouselighting.com.

NOTE: Carefully unpack fixture and parts. Make sure all parts are included before discarding any packing materials (see figure 1).

WARRANTY INFORMATION

This Westinghouse Lighting Fixture is warranted against defects in material and workmanship for a period of Five Years from purchase date. This warranty is in lieu of all other warranties expressed or implied.

This warranty does not cover acts of nature such as lightning damage, or corrosion and discoloration of components, nor does it cover damages caused through abuse, improper installation, surges in electric current, or acts of third parties.

This warranty does not cover broken glass. If fixture is received with broken glass, please call Westinghouse Lighting for free replacement.

This warranty does not cover costs of removing and re-installing the light fixture. If this fixture fails for any reason covered by this warranty, simply return the fixture with a copy of

the original sales receipt, freight prepaid and Westinghouse Lighting, at its option, shall repair or replace the fixture or refund the purchase price.

WARNING ELECTRICAL SHOCK CAN RESULT IN SERIOUS INJURY.

Read and follow instructions exactly as shown. If instructions are unclear, do not proceed. Contact a qualified electrician. Read all instructions before beginning. Proper wiring is essential for safe operation of this fixture. When cutting or drilling into walls or ceilings, do not damage electrical wiring, gas lines, or water lines. If any of the fixture or wiring components are damaged, do not install fixture. Return to place of purchase.

For fixtures provided with 75° C or 90° C supply wire warning only. (These warnings are provided on the U.L. label and on the fixture carton.) Risk of fire. Most dwellings built before 1985 have supply wires rated 60° C. Consult a qualified electrician before installing.

NOTE: For fixture employing a grounded convenience outlet. This fixture employs a grounded type receptacle and is not intended for connection to a two wire ungrounded source of supply.

Applicable only to portable lamps: To reduce the risk of electrical shock, all portable lamps have a polarized plug (one blade is wider than the other). This plug will fit into a polarized outlet only one way. If plug does not fit, reverse the plug. If it still does not fit, contact a qualified electrician. Never use with an extension cord unless plug can be fully plugged into the extension cord. Do not alter the plug.

FIGURE 1.

FIXTURE COVER (K)

CAP NUTS (I)

BACK PLATE (D)

MOUNTING SCREWS (A)

*OUTLET

BOX SCREWS (F)

SIDE HOLE (I)

GREEN GROUNDING SCREW (H)

GROUND WIRE

CROSS BAR (B)

*OUTLET

BOX (E)

WIRE CONNECTORS (G)

FIXTURE BODY (L)

Line art shown may not exactly match the fixture enclosed. However, the installation instructions do apply to this fixture.

SET SCREWS (J)

*NOT SUPPLIED

MOUNTING AND WIRING INSTRUCTIONS

CAUTION: For fixtures labeled for outdoor and wet location use, provide a water-tight seal between the fixture and the mounting surface by using silicone or similar caulking.

NOTE: Underwriters Laboratories (UL) does not require all fixtures to have ground wires. These fixtures meet all UL specifications.

1. Turn off power at circuit box to avoid possible electric shock.

2. Thread mounting screws (A) into universal mounting plate or cross bar (B) approximately 1/4 inch (see fig. 1).

NOTE: If universal mounting plate or cross bar (B) was preinstalled, remove cap nuts (C) and universal mounting plate or cross bar (B) from back plate (D), leaving mounting screws (A) in place.

3. Secure universal mounting plate or cross bar (B) to outlet box (E) with outlet box screws (F).

4. Identify color coding of fixture wires (see fig. 2).

5. To connect wires, take black fixture wire (group A from fig. 2) and place evenly against black outlet box wire. Do not twist wires.

6. Fit wire connector (G from fig. 1) over wires and twist until there is a firm connection. If wire connector (G) easily comes off, reattach and check again for a firm connection.

7. Repeat steps 5 and 6 with the white (group B from fig. 2) fixture wires and outlet box wires.

8. Partially thread green grounding screw (H) into side hole (I) on cross bar (B

9. Wrap ground wire from fixture around green grounding screw (H), leaving enough excess wire to then connect ground wire and outlet box wire with wire connector (G) (see step 11).

10. Tighten green grounding screw (H). Do not over tighten.

11. Tuck wires inside outlet box (E) (see fig. 1).

) (see fig. 1).

universal mounting plate or

FIXTURE ASSEMBLY INSTRUCTIONS

1. Position back plate (D) over mounting screws (A) and secure with cap nuts (C).

2. Remove two set screws (J) from fixture cover (K) and separate from fixture body (L), then remove and discard paper and foam padding (if applicable).

3. Install lamp(s). Do not exceed recommended wattage.

4. Lift fixture body (L) into fixture cover (K) and secure with set screws (J).

5. Turn power back on at circuit box.

+ 8 hidden pages