HIGH TORQUE GARBAGE DISPOSER
1 1/4 HP
TRITURADOR DE BASURA DE MÁXIMO
TORQUE
OWNER’S MANUAL / MANUAL DEL USUARIO
INSTALLATION VIDEO AVAILABLE / VIDEO-INSTALLACIÓN DISPONIBLE
WWW.CONGLOM.COM/DOCUMENTATION
U
C US
R
L
110-120V, 60 HZ
ITM. / ART. 1600061
# QKG06
Table of Contents
Table of Contents ...................................2
Safety Information ..................................2
Warranty ...........................................
Ten (10) Year Limited Warranty .......................3
ENGLISH
Warranty Claim Procedure ...........................3
Pre-Installation
Tools/Materials Required .............................4
Package Contents ..................................4
Installation .........................................
Removal of Old Unit .................................5
Installation of the Mounting Assembly ..................6
Safety Information
READ ALL INSTRUCTIONS BEFORE USING THE APPLIANCE
IMPORTANT SAFETY INSTRUCTIONS
INSTRUCTIONS PERTAINING TO A RISK OF FIRE, ELECTRIC SHOCK, OR
INJURY TO PERSONS. WARNING - WHEN USING ELECTRICAL APPLIANCES,
BASIC PRECAUTIONS SHOULD ALWAYS BE FOLLOWED, INCLUDING THE
FOLLOWING:
Attaching Discharge Elbow ..........................7
Removing Knockout Plug ............................7
Connecting Disposer to Mounting Assembly ..............8
Dishwasher Connection ............................. 9
Electrical Connection & Grounding .....................9
Operation ........................................10
Care and Maintenance .............................10
Troubleshooting ..................................11
Service Parts .....................................12
MANUAL DEL USUARIO .............................13
WARNING: Do not put ngers or hands into a waste
disposer.
WARNING: Turn the power switch to the off position
before attempting to unblock or remove an object from the
disposer.
NOTE:
This food waste disposer has been designed to operate on 110-120 Volt,
60 Hz exclusively. Using any other voltage or Hz adversely affects its performance.
1. Inspect your unit before proceeding. Once you unpack your unit,
check for chips, scratches, cracks, dents or scuff marks. If any
damage is noticed, do not install. Please return to the place of
purchase.
2. Use this unit only in the manner intended by the manufacturer. If you
have any questions, contact the manufacturer.
3. Installation work and plumbing must be done by qualied person(s)
in accordance with all applicable codes and standards.
4. When attempting to loosen an obstruction in a waste disposer, use a
long wooden object such as a wooden spoon or the wooden handle
of a broom or a mop.
5. When attempting to remove objects from a waste disposer, use
long-handled tongs or pliers. If the disposer is magnetically actuated,
non-magnetic tools should be used.
6. When not operating a disposer, leave the drain cover (stopper) in
place to reduce the risk of objects falling into the disposer.
SAVE THESE INSTRUCTIONS
WARNING: Do not operate disposer unless splash guard
is in place.
WARNING: To reduce the risk of injury by materials
that may be expelled by a waste disposer, do not put the
following into a disposer: clam or oyster shells; caustic
drain cleaners or similar products; glass, china or plastic;
large whole bones; metal, such as bottle caps, tin cans,
aluminum foil or utensils; hot grease or other hot liquids;
whole cornhusks.
WARNING: To reduce the risk of injury, close supervision
is necessary when the appliance is used near children.
WARNING: This food waste disposer has been designed
to operate on 110-120 Volt, 8.8A, 60 Hz and 1056W.
2
QKG06
Web: www.conglom.com/documentation/
Warranty
TEN (10) YEAR LIMITED WARRANTY
A thorough inspection must be made before installation and any damage must be promptly reported. We will not be liable for failures or damage that
could have been discovered or avoided by proper inspection and testing prior to installation.
Conglom Kitchen & Bath warrants this product to be free from defects in materials or workmanship for ten (10) years from the date of purchase. Proof
of purchase (original sales receipt) from the original consumer purchaser must be made available to Conglom Kitchen & Bath for all warranty claims.
This warranty is non-transferable and shall be voided if the unit is removed from its initial installation or if it is not installed following the manufacturer’s
instructions. It does not apply in the event of product damage due to the use of other than genuine Conglom Kitchen & Bath replacement parts,
(Replacement parts may be obtained by e-mail at cs@conglomkb.com or by calling 1-877-333-0098 between 8:30 am - 5:00 pm EST) installation
error, abuse, misuse or improper care and maintenance (whether performed by a plumber, contractor, service provider or member of the purchaser’s
household). The warranty excludes damage due to aggressive air or water conditions, harsh or abrasive cleaners and/or materials.
Under no circumstance shall we be held liable for personal injury or property damage resulting from improper installation or use of this product.
We will not be held liable for inconvenience caused by loss of use of this product, costs incurred for labour or materials, removal and installation
of replacement units, or any other incidental or consequential damages. Costs relating to obtaining access for repair or replacement are the
responsibility of the user.
Our obligation shall be limited to the repair or replacement of a unit (at our discretion) that may prove, by our sole examination, to be defective under
normal use and service during the warranty period.
Any failure of this product that is not traceable to a defect in material or workmanship is not covered by this warranty. These non-warrantable items
include, but are not limited to:
- Improper installation not in accordance with manufacturer’s instructions.
- Dents and/or scratches incurred during shipping, handling, or installation.
- Damage caused by failure to follow care and cleaning guidelines.
- Alterations made to the unit by the purchaser or installer.
- Damage caused by accidental impact, re, ood, freezing, and normal wear.
- Bends and warping caused by forced connections, over-tightened ttings, and inadequate support during installation.
ENGLISH
This warranty does not extend to commercial and institutional installation or use.
WARRANTY CLAIM PROCEDURE
If a claimable defect occurs or replacement parts are needed, please contact our customer service team at cs@conglomkb.com or
1-877-333-0098 (Service available in English and French, Monday - Friday from 8:30am - 5pm EST).
Before you make your call, please ensure that you have:
- Model number or description.
- Proof of sale.
- Details regarding the defect and/or part number.
- Name(s) and address(es) of the owner and/or installer.
3 CONGLOMKB.COM
Please contact cs@conglomkb.com or 1-877-333-0098 for further assistance.
Pre-Installation
TOOLS/MATERIALS REQUIRED (NOT SUPPLIED)
Pipe wrench Phillips screwdriver Flat screwdriver
ENGLISH
Electric drill with
1-1/4”(32mm) hole
saw
PACKAGE CONTENTS
A Stopper
Plumber’s putty
B
C
D
E
Part Description Quantity
A Stopper 1
B Removable splash guard 1
Includes:
Sink ange
Rubber sink ange gasket
C
Flange ring
Ring tool
Includes:
Supporting plate
D
Top supporting ring (with 3 screws)
Cushion mount
Splash Guard
Sink Flange
Gasket
Flange Ring
Ring Tool
Supporting Plate
Top Supporting Ring
(with 3 screws)
Cushion Mount
Bottom Supporting Ring
1
1
1
1
1
1
1
Pre-installed on the discharge elbow
F
Elbow Gasket
Discharge Elbow
G
Elbow Flange
*
Screws
Part Description Quantity
E Bottom supporting ring 1
F Disposer body 1
Includes:
Elbow gasket (pre-installed)
G
Discharge elbow
Elbow Flange
Screw
NOTE: This waste disposer is intended to be plugged into a
grounded receptacle that is controlled by a dedicated switch
(usually wall mounted).
1
1
1
2
4
QKG06
Web: www.conglom.com/documentation/
Installation
Fig. 2
Fig. 3
REMOVAL OF OLD UNIT
General instructions - your model may vary.
NOTE:
Before starting this step, turn off the electrical power at the circuit breaker
or fuse box. Unplug the disposer.
- Disconnect dishwasher if connected to the disposer.
- Disconnect drain line where it attaches to the disposer
discharge elbow (see Fig. 1).
- Remove the disposer from the sink ange by turning the
mounting ring clockwise. If you are unable to turn the mounting
ring, tap on one of the extensions from the ring with a hammer.
Some mounting systems have tubular extensions, inserting a
screwdriver into one tube will provide additional leverage for
turning the mounting ring (see Fig. 2).
Some disposers may require the removal or loosening of nuts
from the mounting screws (see Fig. 3). Some disposers may
require the removal of a clamp.
CAUTION: Risk of electric shock. Turn off electric
power at fuse box or circuit breaker before removing
old unit.
CAUTION: Be sure to support the disposer when
removing the mounting ring or it may fall.
Fig. 1
ENGLISH
NOTE:
If your disposer has the same ange as the new disposer and you would
like to keep your old ange, you may skip the following steps and skip to
page 7. If you would like to replace your existing ange or if the ange is
different, please continue with the following steps
- To remove the remaining mounting system from the sink,
loosen the mounting screws and push the mounting ring up.
Under it is the snap ring. Use a screwdriver to pop off the ring
(see Fig. 4). Remove the mounting ring, the protector ring and
the gasket from the sink ange. Some mountings will require
the unscrewing of a large ring holding the sink ange in place.
Pull the sink ange up through the sink and clean off the old
putty from the sink.
NOTE:
This is a good time to clean out the trap and drain lines by running a drain
auger or plumber’s snake before installing your new disposer.
.
Fig. 4
5 CONGLOMKB.COM
Please contact cs@conglomkb.com or 1-877-333-0098 for further assistance.
Installation (continued)
INSTALLATION OF MOUNTING ASSEMBLY
NOTE:
Pay close attention how the parts come assembled, as they have been
correctly assembled by the factory (see Fig. 5).
ENGLISH
This food waste disposer has been designed to operate on 110-120 Volt,
60 Hz electrical circuit.
- Disassemble the mounting assembly from the disposer by turning
the bottom supporting ring clockwise.
Top supporting ring
Top supporting ring screw
Fig. 5a
- Loosen the 3 screws all the way or remove them from the top
supporting ring (Fig. 5a), then use a screw driver to remove the
ange ring (Fig. 5b).
- The sink ange may be installed with or without use of plumber’s
putty (see Fig 7 and 7a).
If you use putty, (see Fig. 7a) form a ring around the underside of
the sink ange (see Fig. 6). Insert the ange into the sink opening,
press down hard to squeeze out the excess putty. Trim off excess
putty from the top and bottom of the sink opening (see Fig. 7b). Do
not rotate the ange once it is seated.
Fig. 6
- Use duct tape or place a heavy object on top of the sink ange to
keep it in place.
- Stretch the ange ring and insert the ends securely into the ring
tool. Keep your ngers away from the ends of the ange ring at all
times (see Fig. 8).
Sink
Fig. 7
Flange ring
Flange
Flange ring
Sink
flange
Gasket
Supporting
plate
Ring tool
Fig. 5b
Recommended
Sink
Sink flange
Plumber’s
Putty
Gasket
Supporting
plate
Fig. 7a Fig. 7b
Groove of
sink flange
Supporting plate
Top supporting ring
- Insert the supporting plate and the top supporting ring and hold
them in place. Place the ring tool in the groove of the sink ange
with the arrow side towards you facing towards the bottom. Using
your thumb, push the opposite end of the ange ring until it snaps
into the groove of the sink ange (see Fig. 8a).
- Release the ring tool by rotating it downwards until it snaps away
from the ange ring (see Fig. 8b).
- Tighten the 3 top supporting ring screws sequentially until the
ange is very securely fastened to the sink (see Fig. 8c)
6
QKG06
Web: www.conglom.com/documentation/
Fig. 8
Fig. 8b
2
Ring tool
1
Top supporting
ring screw
Sink flange
Fig. 8a
3
Fig. 8c
Flange ring
Installation (continued)
If at any time the bottom supporting ring becomes disengaged
from the body of the waste disposer, then:
1. Align the slot in the bottom supporting ring with tab on the
waste disposer body.
2. Lower the bottom supporting ring and make the slot t in the
tab.
3. Turn the bottom supporting ring counter clockwise to secure it
in place.
ATTACHING DISCHARGE ELBOW
- Take off the elbow gasket from the discharge elbow rst, then
attach the ange to the discharge elbow, then reset the elbow
gasket (see Fig. 9a).
- Make sure the elbow gasket is attached to the discharge elbow
correctly (see Fig. 9b).
- Connect the discharge elbow to the disposer (see Fig. 9c).
Elbow
Gasket
Slot
Tab
Discharge
Elbow
Flange
Fig.9a
Elbow Gasket
Fig. 9b
ENGLISH
Groove
Discharge Elbow
REMOVING KNOCKOUT PLUG
If you are using a dishwasher, complete the following procedure. If no
dishwasher is to be connected, skip this section.
- Using a blunt instrument (steel punch or wooden dowel),
knock out the entire plug (see Fig. 10). Do not use a
screwdriver or sharp instrument. When the knockout plug falls
into the disposer, you may remove it, or grind it up when the
disposer is being used. This will not damage the disposer in
any way, but may take some time to grind.
7 CONGLOMKB.COM
Fig.9c
Knockout
Plug
Wood or
Metal Dowel
Fig. 10
Please contact cs@conglomkb.com or 1-877-333-0098 for further assistance.
Installation (continued)
Sink
CONNECTING THE DISPOSER TO THE
MOUNTING ASSEMBLY
Fig. 11
ENGLISH
- Adjust the disposer position to make the elbow line up with the
- The disposer must be installed so that the reset button is
- Make sure the cushion mount is properly in place. Line up
trap (see Fig. 11).
readily accessible (see Fig. 12).
the disposer under the mounting assembly. Lift and guide the
disposer so that all three tabs of the bottom supporting ring
engage the steps of the top supporting ring. Turn the bottom
supporting ring counter-clockwise until it is fully engaged and
the tool mount comes in contact with the top supporting ring.
Insert a screw driver into the tool mount for added leverage, if
needed (see Fig 13a).
Top
supporting
ring
Bottom
supporting
ring
Mounting
Assembly
Cushion Mount
Elbow
Trap
Disposer body
Reset Button
Fig. 12
Sink
Step
Tab
Tool
Mount
Tool Mount
If you are unable to fully engage the bottom supporting ring,
release and lower the waste disposer (see Fig 13b).
8
QKG06
Web: www.conglom.com/documentation/
Fig.13
Fig.13a
Fig. 13b
Loading...