Page 1
Installation and Assembly - Flat/tilting
wall mount for LCD screen
Model: MT25 TIL T
IMPORT ANT! Read entire instruction sheet
before you start installation and assembly.
Parts List
PART # QTY. DESCRIPTION
A 095-4034 1 wall bracket
B 095-4140 1 tilt bracket
C 504-2013 4 M4 x .7 x 12 mm phillips screw
D 520-2005 4 M5 x 10 mm phillips screw
E 500-2002 2 #10 X 1 1/2" wood screw
F 590-0097 2 concrete anchor
G 520-2027 4 M4 x .7 x 10 mm phillips screw
H 504-2014 4 M4 x .7 x 20 mm phillips screw
I 590-5003 4 retaining spacer
CHG
D
Maximum Load Capacity:
25 lb (11.4 kg)
A
R
B
FE
Visit the Westinghouse Web Site at www.westinghousedigital.com For customer service call 1-866-287-5555.
I
ISSUED: 04-16-04 SHEET #: 095-9193-11 of 5
Page 2
Insert two screws (D) into
wall bracket (A).
For Wood Stud Walls use a stud finder to locate center
of stud. Drill two 1/8" (3 mm) dia. holes to a minimum
depth of 1.5" (64 mm). Attach wall bracket (A) to center
of wood stud using two screws (E).
WARNING
A
D
• Tighten wood screws so that wall plate is firmly
attached, but do not overtighten. Overtightening can
damage the screws, greatly reducing their holding
power.
• Never tighten in excess of 80 in • lb (9 N.M.).
• Make sure that mounting screws are anchored into the
center of the studs. The use of an "edge to edge" stud
finder is highly recommended.
WOOD
STUD
WALL
A
E
ISSUED: 04-16-04 SHEET #: 095-9193-12 of 5
Visit the Westinghouse Web Site at www.westinghousedigital.com For customer service call 1-866-287-5555.
Page 3
WARNING
• When installing wall mounts on cinder block, verify that
you have a minimum of 1 5/8" of actual concrete surface
in the 1/4" diameter hole to be used for the concrete
anchors. It is suggested that a standard electric drill on
slow setting is used to drill the hole instead of a hammer
drill to avoid breaking out the back of the hole when
entering a void or cavity. Do not drill into mortar joints,
which are brittle and will not provide a stable anchorage!
For Concrete Walls drill one 1/4" (6 mm) dia. hole to a
minimum depth of 1.5" (64 mm). Insert anchor (F) in hole
flush with wall as shown (right). Place wall bracket (A) over
anchor (F) and secure with #10 x 1.5" wood screw (E). Make
sure wall bracket is level, mark other hole and repeat steps
with other fasteners. Tighten all fasteners.
WARNING
• Tighten wood screws firmly , but do not overtighten.
Overtightening can damage the screws, greatly
reducing their holding power.
• Never tighten in excess of 80 in • lb (9 N.M.).
E
3A
F
A
concrete
wall
WARNING
• Never use concrete expansion anchors for attachment
of wall plate to concrete walls covered with a layer of
plaster, drywall, or other finishing material.
CUT AW A Y VIEW
F
Drill hole and insert anchor (F)
3B
A
E
F
Place wall bracket (A) over anchor (F) and secure with
screw (E)
3C
After repeating step one tighten all fasteners
ISSUED: 04-16-04 SHEET #: 095-9193-13 of 5
Visit the Westinghouse Web Site at www.westinghousedigital.com For customer service call 1-866-287-5555.
Page 4
This product is designed to accommodate screens with Vesa® compliant hole
pattern. For safe mounting, please make sure that mounting screws turns at least
three complete turns in the screen inserts.
FOR VESA 75 MOUNTING PATTERN: 1. Choose
hole pattern indicated below. 2. Attach tilt bracket
(B) to back of screen using four 10 mm screws
(G) as indicated below. 3. If hole pattern is in a
pocket, attach tilt bracket (B) to back of screen
using four 20 mm screws (H) and four retaining
spacers (I) as indicated below.
For screens with a hole
pattern in a pocket,
spacers (I) go between tilt
bracket (B) and screen.
B
Note: Screen may appear
slightly different than
illustrated
FOR VESA 100 MOUNTING PATTERN: 1. Choose
hole pattern indicated below. 2. Attach tilt bracket (B)
to back of screen using four 10 mm screws (G) as
indicated below. Note: If you don't get three complete
turns in the screen inserts, use four M4 x 12 mm
screws (C) instead of four M4 x 10 mm screws (G).
B
WARNING
• The screen and bracket may be too heavy and bulky for
one person to handle safely. Two or more persons, or
mechanical lifting equipment, should always be used to
securely attach the screen to the wall bracket. Refer to
your screen’s owner’s manual for additional installation
instructions.
Hook tilt bracket (B) onto wall bracket (A).
Adjust tilt (15° forward and 5° back) and
secure with two M5 screws (D).
SCREEN
SCREEN
D
B
Note: Refer to your TV owner’s manual for additional instructions which may pertain to the positioning of your
specific TV .
Visit the Westinghouse Web Site at www.westinghousedigital.com For customer service call 1-866-287-5555.
A
ISSUED: 04-16-04 SHEET #: 095-9193-14 of 5
Page 5
Limited Five-Year Warranty
Westinghouse Digital Electronics warrants to original end-users of this Westinghouse television mounting product (the
“Product”) that the Product will be free from defects in material and workmanship, under normal use, for a period of five (5)
years from the date of purchase by the original end-user, subject to the following terms and conditions:
REP AIR OR REPLACEMENT – For a period of five (5) years from the original date of purchase, W estinghouse Digit al
Electronics will repair any defect in material or workmanship in the Product, or , at its option, replace a defective Product.
Replacement parts and products will be warranted for either the remainder of the original warranty period or ninety (90)
days from the date of delivery to the end-user, whichever occurs last.
OBT AINING WARRANTY SER VICE – To obtain warranty services, you must either personally deliver or ship the Product
to Westinghouse Digital Electronics, freight prepaid. Please call Westinghouse Digital Electronics at (866) 287-5555 to
obtain a Return Merchandise Authorization (“RMA”) and for other instructions regarding return and replacement or repair of
the Product. Westinghouse Digital Electronics will not accept Products delivered to it without an RMA.
EXCLUSIONS TO W ARRANTY – This warranty does not cover damage caused by (a) service or repairs by anyone other
than personnel authorized by Westinghouse Digital Electronics, (b) the failure to utilize proper packing when returning the
product, (c) improper installation or the failure to follow Product instructions or warnings, or (d) misuse or accident, in
transit or otherwise.
PROOF OR ORIGINAL PURCHASE – A sales receipt, invoice, or other proof of purchase specifying the original date of
purchase within the five (5) year warranty period must be presented to obtain warranty service. This warranty extends to
the original purchaser and is not transferable.
EITHER REP AIR OR REPLACEMENT IS YOUR EXCLUSIVE REMEDY UNDER THIS WARRANTY. EXCEPT TO THE
EXTENT PROHIBITED BY LAW, WESTINGHOUSE DIGITAL SHALL NOT BE LIABLE FOR ANY INCIDENTAL OR
CONSEQUENTIAL DAMAGES CLAIMED T O ARISE FROM BREACH OF ANY EXPRESS OR IMPLIED W ARRANTY ON
THIS PRODUCT . ANY IMPLIED WARRANTY OF MERCHANT ABILITY OR FITNESS FOR A P ARTICULAR PURPOSE
ON THIS PRODUCT IS LIMITED IN DURA TION AND SCOPE TO THE TERMS OF THIS WARRANTY .
Some St ates do not allow the exclusion or limitation of incidental or consequential damages, or allow limitations on how
long an implied warranty lasts, so the above limitation may not apply to you. This warranty gives specific legal rights, and
you may also have other rights which vary from S tate to S tate.
Westinghouse Digital Electronics, LLC
16257 East Gale A ve.
City of Industry , California 91745
T el: (626) 333-9677.
ISSUED: 04-16-04 SHEET #: 095-9193-15 of 5
Visit the Westinghouse Web Site at www.westinghousedigital.com For customer service call 1-866-287-5555.
and Westinghouse are trademarks of Westinghouse Electric Corporation and are used under license.
Loading...