Installation and Assembly Swivel Wall Arm for LCD screens
Model: MT25 ARM9
IMPORT ANT! Read entire instruction sheet
before you start installation and assembly.
Parts List
PART #QTY. DESCRIPTION
A 095-01491LCD screen swing arm
B 590-11101cord wrap
C 590-50034retaining spacer
D 500-20112#14 X 2" wood screw
E 590-00972concrete anchor
F 504-20134M4 x .7 x 12 mm philips head screw
G 520-20274M4 x .7 x 10 mm philips head screw
H 504-20144M4 x .7 x 20 mm philips head screw
Max. Load 25 lb (1 1.34 kg)
A
C
B
D
E
Visit the Westinghouse Web Site at www.westinghousedigital.com For customer service call 1-866-287-5555.
F
G
ISSUED: 04-16-04 SHEET #: 095-9194-11 of 6
H
Page 2
Remove knob from tilt/adapter plate.
TILT/ADAPTER
PLATE
KNOB
For Wood Stud Walls: Use a stud finder to locate
center of stud. Drill two 3/16" (5 mm) dia. holes to a
minimum depth of 2" (51 mm). Attach swing arm to
center of wood stud using two screws (D).
IMPORTANT: Make sure wall bracket is level on wall.
WARNING
• Tighten wood screws so that wall plate is firmly
attached, but do not overtighten. Overtightening can
damage the screws, greatly reducing their holding
power.
• Never tighten in excess of 80 in • lb (9 N.M.).
• Make sure that mounting screws are anchored into the
center of the studs. The use of an "edge to edge" stud
finder is highly recommended.
WOOD
STUD
WALL
WALL
BRACKET
D
ISSUED: 04-16-04 SHEET #: 095-9194-12 of 6
Visit the Westinghouse Web Site at www.westinghousedigital.com For customer service call 1-866-287-5555.
Page 3
WARNING
• When installing Peerless wall mounts on cinder block, verify that you have a minimum of 1-3/8" of actual concrete
surface in the hole to be used for the concrete anchors. Do not drill into mortar joints! Be sure to mount in a solid
part of the block, generally 1" minimum from the side of the block. Cinder block must meet ASTM C-90 specifications. It is suggested that a standard electric drill on slow setting is used to drill the hole instead of a hammer drill
to avoid breaking out the back of the hole when entering a void or cavity .
• Concrete must be 2000 psi density minimum. Lighter density concrete may not hold concrete anchor .
• Make sure that the wall will safely support four times the combined load of the equipment and all attached hardware and components.
For Concrete Walls drill one 1/4" (6 mm) dia. hole to a
minimum depth of 2" (51 mm). Insert anchor (E) in hole
flush with wall as shown (right). Place wall bracket, with
slot on tube facing down, over anchor (E) and secure
with #14 x 2" wood screw (D). Make sure wall bracket is
level, mark other hole and repeat steps with other
fasteners. Tighten all fasteners.
IMPORTANT: Make sure wall bracket is level on wall.
WALL
BRACKET
E
WARNING
• Tighten concrete anchor bolts firmly, but do not
overtighten. Overtightening can damage the bolts,
greatly reducing their holding power.
• Never tighten in excess of 80 in • lb (9 N.M.).
WARNING
• Concrete anchors are not intended for attachment to
concrete wall covered with a layer of plaster, drywall,
or other finishing material. If mounting to concrete wall
covered with plaster/drywall is unavoidable, plaster/
drywall (up to 5/8" thick) must be counterbored as
shown below. If plaster/drywall is thicker than 5/8",
custom fasteners must be supplied by installer .
D
1
Drill hole and insert anchor (E)
2
Place wall bracket over anchor (E) and secure with
screw (D)
wall bracket
D
concrete
wall
E
E
3
CUT AW A Y VIEW
After repeating step one tighten all fasteners
ISSUED: 04-16-04 SHEET #: 095-9194-13 of 6
Visit the Westinghouse Web Site at www.westinghousedigital.com For customer service call 1-866-287-5555.
Page 4
This product is designed to accommodate screens with Vesa® compliant hole
pattern. For safe mounting, please make sure that mounting screws turns at least
three complete turns in the screen inserts.
FOR VESA 75 MOUNTING PATTERN: 1.
Choose hole pattern indicated below. 2. Attach
tilt/adapter plate to back of monitor using four
10 mm screws (G) as indicated below. 3. If
hole pattern is in a pocket, attach tilt/adapter
plate to back of monitor using four 20 mm
screws (H) and four retaining spacers (C) as
indicated below.
Note: Screen may appear slightly
different than illustrated
For screens with a hole
pattern in a pocket,
spacers (C) go between
tilt/adapter plate and
monitor.
G or H
FOR VESA 100 MOUNTING PATTERN: 1.
Choose hole pattern indicated below. 2. Attach
tilt/adapter plate to back of monitor using four 10
mm screws (G) as indicated below. Note: If you
don't get three complete turns in the screen
inserts, use four M4 x 12 mm screws (F) instead
of four M4 x 10 mm screws (G).
Note: Screen may appear slightly
different than illustrated
TIL T/AD APTER
PLA TE
TIL T/AD APTER
PLA TE
G or F
ISSUED: 04-16-04 SHEET #: 095-9194-14 of 6
Visit the Westinghouse Web Site at www.westinghousedigital.com For customer service call 1-866-287-5555.
Page 5
Flip LCD upward. Wrap power and A/V cords
with cord wrap. Feed cord wrap through hole on
bottom of wall bracket into tube to avoid pinching wires between wall bracket and tube. Next
route through and between pivot bracket and tilt/
adapter plate.
TIL T/AD APTER
PLA TE
LCD SCREEN
PIVOT
BRACKET
CUT AWA Y
OF TUBE
CORD
WRAP
POWER
CORD
Adjust tilt and secure pivot bracket to tilt/adapter plate with knob.
KNOB
ISSUED: 04-16-04 SHEET #: 095-9194-15 of 6
Visit the Westinghouse Web Site at www.westinghousedigital.com For customer service call 1-866-287-5555.
Page 6
Limited Five-Year Warranty
Westinghouse Digital Electronics warrants to original end-users of this Westinghouse television mounting product (the
“Product”) that the Product will be free from defects in material and workmanship, under normal use, for a period of five (5)
years from the date of purchase by the original end-user, subject to the following terms and conditions:
REP AIR OR REPLACEMENT – For a period of five (5) years from the original date of purchase, W estinghouse Digit al
Electronics will repair any defect in material or workmanship in the Product, or , at its option, replace a defective Product.
Replacement parts and products will be warranted for either the remainder of the original warranty period or ninety (90)
days from the date of delivery to the end-user, whichever occurs last.
OBT AINING WARRANTY SER VICE – To obtain warranty services, you must either personally deliver or ship the Product
to Westinghouse Digital Electronics, freight prepaid. Please call Westinghouse Digital Electronics at (866) 287-5555 to
obtain a Return Merchandise Authorization (“RMA”) and for other instructions regarding return and replacement or repair of
the Product. Westinghouse Digital Electronics will not accept Products delivered to it without an RMA.
EXCLUSIONS TO W ARRANTY – This warranty does not cover damage caused by (a) service or repairs by anyone other
than personnel authorized by Westinghouse Digital Electronics, (b) the failure to utilize proper packing when returning the
product, (c) improper installation or the failure to follow Product instructions or warnings, or (d) misuse or accident, in
transit or otherwise.
PROOF OR ORIGINAL PURCHASE – A sales receipt, invoice, or other proof of purchase specifying the original date of
purchase within the five (5) year warranty period must be presented to obtain warranty service. This warranty extends to
the original purchaser and is not transferable.
EITHER REP AIR OR REPLACEMENT IS YOUR EXCLUSIVE REMEDY UNDER THIS WARRANTY. EXCEPT TO THE
EXTENT PROHIBITED BY LAW, WESTINGHOUSE DIGITAL SHALL NOT BE LIABLE FOR ANY INCIDENTAL OR
CONSEQUENTIAL DAMAGES CLAIMED T O ARISE FROM BREACH OF ANY EXPRESS OR IMPLIED W ARRANTY ON
THIS PRODUCT . ANY IMPLIED WARRANTY OF MERCHANT ABILITY OR FITNESS FOR A P ARTICULAR PURPOSE
ON THIS PRODUCT IS LIMITED IN DURA TION AND SCOPE TO THE TERMS OF THIS W ARRANTY .
Some States do not allow the exclusion or limit ation of incidental or consequential damages, or allow limitations on how
long an implied warranty lasts, so the above limitation may not apply to you. This warranty gives specific legal rights, and
you may also have other rights which vary from S tate to S tate.
Westinghouse Digital Electronics, LLC
16257 East Gale A ve.
City of Industry , California 91745
T el: (626) 333-9677.
ISSUED: 04-16-04 SHEET #: 095-9194-16 of 6
Visit the Westinghouse Web Site at www.westinghousedigital.com For customer service call 1-866-287-5555.
and Westinghouse are trademarks of Westinghouse Electric Corporation and are used under license.
Loading...
+ hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.