Westinghouse MT150 User Manual
Installation and Assembly:
Universal Tilt Wall Mount for 37" - 47" Screens
Model: MT150 TILT
This product is UL Listed. It must be
R
installed by a qualified professional
installer.
Features:
• Universal design for 37" - 47" flat panel screens
• One-touch tilt for effortless positioning and adjustment of the screen
• Ultra-slim design holds the screen flat against the wall
• IncreLok™ locking tilt positions for specific tilt settings in 5° increments
• Comes in black
Visit the Westinghouse Web Site at www.westinghousedigital.com
Max Load Capacity: 150 lb (68kg)
For customer care call 1-866-287-5555.
ISSUED: 02-08-06 SHEET #: 202-9093-1
Note: Read entire instruction sheet before you start installation and assembly.
WARNING
• Do not begin to install your Westinghouse product until you have read and understood the instructions and warnings
contained in this Installation Sheet. If you have any questions regarding any of the instructions or warnings, please
call customer care at 1-866-287-5555.
• This product should only be installed by someone of good mechanical aptitude, has experience with basic building
construction, and fully understands these instructions.
• Make sure that the supporting surface will safely support the combined load of the equipment and all attached hardware and components.
• Never exceed the Maximum UL Load Capacity of 150 lb (68 kg).
• If mounting to wood wall studs, make sure that mounting screws are anchored into the center of the studs. Use of an
"edge to edge" stud finder is highly recommended.
• Always use an assistant or mechanical lifting equipment to safely lift and position equipment.
• Tighten screws firmly , but do not overtighten. Overtightening can damage the items, greatly reducing their holding
power.
Tools Needed for Assembly
• stud finder ("edge to edge" stud finder is recommended)
• phillips screwdriver
• drill
• 1/4" bit for concrete and cinder block wall
• 1/2" bit for metal stud wall
• 5/32" bit for metal or wood stud wall
• level
Accessories
• 4 piece Metal S tud Fastener Kit (ACC 415) (Metal Stud not evaluated by UL)
• 2 piece Metal S tud Fastener Kit (ACC 215) (Metal Stud not evaluated by UL)
Table of Contents
Parts List..............................................................................................................................................................................3
Installation to Double Wood Stud Wall..................................................................................................................................4
Installation to Solid Concrete or Cinder Block .......................................................................................................................5
Installing Tilt Brackets...........................................................................................................................................................6
Installing Flat Panel Screen to Wall Plate.............................................................................................................................7
For customer care call 1-866-287-5555
2 of 8
ISSUED: 02-08-06 SHEET #: 202-9093-1
Before you begin, make sure all parts shown are included with your product.
Parts may appear slightly different than illustrated.
Parts L ist
De scri p tion Qty. Par t #
wall plate 1 200-4797
AA
Left t i lt brack et 1 200-0905
BB
Right t i lt bracket 1 200-0906
CC
#14 x 2.5" hex head s c rew 4 5S1-015-C03
DD
All igat or® anc hor 4 590-0097
EE
4 mm al l en wre nch 1 560-1131
FF
AA
DD
EE
BB
CC
FF
Adapter Bracket Fasteners
Note: The sorted-for-you™ fastener pack included was made specifically for your product and may not contain all components
shown below.
M4 x 12 mm (6)
M4 x 25 mm (4)
I.D. 5.1 mm (4)
Penta-Pin Driver (1)
M5 x 12 mm (4)
I.D. 8.9 mm (6)
M5 x 25 mm (4)
M6 x 12 mm (4)
M6 x 20 mm (4)
M6 x 25 mm (4)
I.D. 5.6 mm (4)
I.D. 8.7 mm (4)
M6 x 30 mm (4)
M8 x 16 mm (6) M8 x 40 mm (6)
M8 x 25 mm (4)
3 of 8
M10 x 15 mm (4)
I.D. 6.5 mm (4) multi-washer (6)
ISSUED: 02-08-06 SHEET #: 202-9093-1
Loading...