Westermo Viper-012 User Manual

User Guide

6641-2242

Viper-12

SERIES

RSTP FRNT

Westermo Teleindustri AB

X10

USB

X12

CON

X10

X12

12-port Ethernet M12 switch / GigE

www.westermo.com

Software tools

Related software tools are available in the folder software tools under technical support on the Westermo website.

License Information

This device contains public available software which is under the GPL license. For more information see legal.pdf included with all firmware releases. This product includes software developed by the OpenSSL Project for use in the

OpenSSL Toolkit. http://www.openssl.org

Legal information

The contents of this document are provided “as is”. Except as required by applicable law, no warranties of any kind, either express or implied, including, but not limited to, the implied warranties of merchantability and fitness for a particular purpose, are made in relation to the accuracy and reliability or contents of this document. Westermo reserves the right to revise this document or withdraw it at any time without prior notice.

Under no circumstances shall Westermo be responsible for any loss of data or income or any special, incidental, and consequential or indirect damages howsoever caused.

More information about Westermo can be found at the following Internet address:

http://www.westermo.com

6641-2242

Safety

Before installation:

Read this manual completely and gather all information on the unit. Make sure that you understand it fully. Check that your application does not exceed the safe operating specifications for this unit.

This unit should only be installed by qualified personnel.

This unit should be built-in to an apparatus cabinet, or similar, where access is restricted to service personnel only. The power supply wiring must be sufficiently fused, and if necessary it must be possible to disconnect manually from all power supply. Ensure compliance to national installation regulations. This unit relies on convection heating. Make sure that it is installed so that the ambient temperature is within the specified temperature range, e.g. by avoiding obstruction of the airflow around the unit. Also check chapter CEN/TS 45545-2 mounting notes.

Before mounting, using or removing this unit:

Prevent access to hazardous voltage by disconnecting the unit from all power supply.

WARNING

Do not open connected unit. Hazardous voltage may occur within this unit when connected to power supply.

Before powering-up, a protective earthing conductor must be connected to the protective earthing terminal and have a cross-sectional area of at least 1.5 mm². Note that this unit can be connected to two different power sources.

When this unit is operated at an ambient temperature above +60°C (+140°F), the External Surface of Equipment may exceed Touch Temperature Limit according to EN/IEC/UL 60950-1. To reduce the risk of fire, use only No. 26 AWG or larger telecommunication line cord.

6641-2242

Care recommendations

Follow the care recommendations below to maintain full operation of unit and to fulfill the warranty obligations:

… Do not attempt to dissassemble the unit. There are not any user serviceable

parts inside.

… Do not drop, knock or shake the unit. Rough handling above the specification

may cause damage to internal circuit boards.

… Do not use harsh chemicals, cleaning solvents or strong detergents to clean the

unit.

… Do not expose the unit to any kind of liquid (water, beverages, paint etc),

unless all connectors are connected or fitted with protective caps (delivered with the unit), tightened to the specified torque. Connected cables must have the appropriate ingress protection code.

… Do not use or store the unit in dusty or dirty areas, unless all connectors and

the ventilation membrane are sufficiently protected.

… Do not cover or bring mechanical force to the ventilation membrane on the

back of the unit.

If the unit is not working properly, contact the place of purchase, nearest Westermo distributor office or Westermo Tech support.

Maintenance

No maintenance is required, as long as the unit is used as intended within the specified conditions.

6641-2242

Agency approvals and standards compliance

Type Approval / Compliance

EMC EN 61000-6-1, Immunity residential environments

EN 61000-6-2, Immunity industrialokokvironments

EN 61000-6-3, Emission residential environments

EN 61000-6-4, Emission industrial environments

EN 50121-3-2, Railway applications – Rolling stock – apparatus

EN 50121-4/IEC 62236-4, Railway signaling and telecommunications apparatus

FCC Part 15 Class B

Safety EN 60950-1, IT equipment

Environmental EN 61373

FCC Part 15.105 Notice:

Railway applications – Rolling stock equipment. Shock and vibration tests

IEEE 1478 Environmental conditions for transit rail car electronic equipment

EN 50124-1 Railway applications – Insulation coordination

EN 50155 Railway applications – Electronic equipment used on rolling stock

IEC 60068-2-27, (shock 100g, 6 ms, halfsine)

CEN/TS 45545-2 Fire safety standard

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a partic ular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

… Reorient or relocate the receiving antenna … Increase the separation between the equipment and receiver … Connect the equipment into an outlet on a circuit different from that to which

the receiver is connected

… Consult the dealer or an experienced radio/TV technician for help.

6641-2242

Declaration of Conformity

Westermo Teleindustri AB

Declaration of conformity

The manufacturer Westermo Teleindustri AB

Herewith declares that the product(s)

Type of product Model Art no 12-port unmanaged Ethernet M12 Switch Viper-012 3641-0540 12-port managed Ethernet M12 Switch Viper-112, -212 3641-0555, -0560

is in conformity with the following EC directive(s).

No Short name

2004/108/EC Electromagnetic Compatibility (EMC) 2006/95/EC Low Voltage (LVD) 2011/65/EU Restriction of the use of certain hazardous substances in electrical and electronic

References of standards applied for this EC declaration of conformity. No Title Issue

EN 50121-3-2 Railway applications – Electromagnetic compatibility – Rolling stock -

EN 50121-4 Railway applications – Electromagnetic compatibility – Emission and immunity

EN 61000-6-1 Electromagnetic compatibility - Generic standards - Immunity for residential,

EN 61000-6-2 Electromagnetic compatibility - Generic standards - Immunity for industrial

EN 61000-6-3 Electromagnetic compatibility – Emission for residential environments 2007

EN 61000-6-4 Electromagnetic compatibility - Generic standards - Emission standard for

EN 60950-1 Information technology equipment – Safety – General require ments 2006

EN 50581 Technical documentation for the assessment of electrical and electronic products

The last two digits of the year in which the CE marking was affixed: 15

SE-640 40 Stora Sundby, Sweden

equipment (RoHS)

Apparatus

of the signaling and telecommunications apparatus

commercial and light-industrial environments

environments

industrial environments

with respect to the restriction of hazardous substances

2015

2007

2005

+ A1:2011 2007 +A1:2011

+A11:2009 +A1:2010 +A12:2011 2012

Pierre Öberg Technical Manager 20

September 2015

Org.nr/ Postadress/Postal address

S-640 40 Stora Sundby 016-428000 016-428001 52 72 79-4 5671-5550 556361-2604 Eskilstuna

Sweden Int+46 16428000 Int+46 16428001

Tel.

Telefax

Postgiro

Bankgiro Corp. identity number Registered office

6641-2242

Declaration of Conformity

Westermo Teleindustri AB

Declaration of conformity

The manufacturer Westermo Teleindustri AB

Herewith declares that the product(s)

Type of product Model Art no 12-port managed Gig Ethernet M12 Switch Viper-112-T3G, -212-T3G 3641-0530, -0550