How it Works
Westermo
Loading...
L106-S2
User Manual
24 pgs1.34 Mb0

Westermo L206-S2, L106-S2 User Manual

Lynx DSS L106-S2/L206-S2
www.westermo.com
Industrial Ethernet 6-port Device Server Switch
WeOS
2
General information
Legal information
The contents of this document are provided “as is”. Except as required by applicable law, no warranties of any kind, either express or implied, including, but not limited to, the implied warranties of merchantability and fitness for a particular purpose, are made in relation to the accuracy and reliability or contents of this document. Westermo reserves the right to revise this document or withdraw it at any time without prior notice.
Under no circumstances shall Westermo be responsible for any loss of data or income or any special, incidental, and consequential or indirect damages howsoever caused.
More information about Westermo can be found at the following address:
www.westermo.com
Software tools
Related software tools are available in the folder software tools under technical support on the Westermo website.
License and copyright for included Free/Libre Open Source Software
This product includes software developed by third parties, including Free/Libre Open Source Software (FLOSS). The specific license terms and copyright associated with the software are included in each software package respectively. Please visit the product web page for more information.
Upon request, the applicable source code will be provided. A nominal fee may be charged to cover shipping and media. Please direct any source code request to your normal sales or support channel.
WeOS Management Guide
This product runs WeOS (Westermo Operation System). Instructions for quick start, configuration, factory reset and use of USB port are found in the WeOS Management Guide at www.westermo.com.
3
Safety
Before installation:
Read this manual completely and gather all information on the unit. Make sure that you understand it fully. Check that your application does not exceed the safe operating specifications for this unit.
Warning - Hazardous voltage
The product must be installed by qualified service personnel and built in to an apparatus cabinet or similar, where access is restricted to service personnel only.
Before powering up, a protective earthing conductor must be connected to the protective earthing terminal. Westermo recommends a cross-sectional area of at least 4 mm 2 on the protective earthing conductor.
Do not open a connected product. Hazardous voltage may occur when connected to a power supply.
Disconnect all network connectors and cable distribution system connectors, including power supply, before disconnecting the protective earthing terminal.
Warning - Protective fuse
The power supply wiring must be sufficiently fused. It must be possible to disconnect manually from the power supply. Ensure compliance to national installation regulations. Refer to the user guide for detailed information.
Replacing the internal fuse must only be performed by Westermo qualified personell.
Warning - Reduce the risk of fire
To reduce the risk of fire, use only no. AWG 26 or larger telecommunication line cord.
4
Caution - Electrostatic discharge (ESD)
Prevent damage to internal electronic parts from electrostatic discharge (ESD) by discharging your body to a grounding point (e.g. use of a wrist strap).
Caution - Hot surface
Be aware of that the surface of this product may become hot. When it is operated at high temperatures, the external surface may exceed Touch Temperature Limit according to EN/IEC/UL 60950-1.
Westermo’s products are fanless and use convection cooling. To avoid obstructing the airflow around the product, follow the spacing recommendations.
Caution - Wiring
Ensure that the temperature rating of the cable is sufficient for the application before connecting to the field wiring terminals.
Note
This unit can be connected to two different power sources.
5
Product disposal
This symbol means that the product shall not be treated as unsorted municipal waste when disposing of it. It needs to be handed over to an applicable collection point for recycling electrical and electronic equipment.
By ensuring this product is disposed of correctly, you will help to reduce hazardous substances and prevent potential negative consequences to both environment and human health, which could be caused by inappropriate disposal.
Care recommendations
Follow the care recommendations below to maintain full operation of unit and to fulfill the warranty obligations:
• Do not drop, knock or shake the unit. Rough handling above the specification may cause damage to internal circuit boards.
• Do not use harsh chemicals, cleaning solvents or strong detergents to clean the unit.
• Do not paint the product. Paint can clog the product and prevent proper operation.
If the unit is not working properly, contact the place of purchase, nearest Westermo distributor office or Westermo technical support.
6
Simplified EU declaration of conformity
Hereby, Westermo declares that the equipment is in compliance with EU directives. The full EU declaration of conformity and other detailed information are available at the respective product page at www.westermo.com. .
Agency approvals and standards compliance
Type Approval / Compliance
EMC EN 61000-6-1, Immunity residential environments
EN 61000-6-2, Immunity industrial environments
EN 61000-6-3, Emission residential environments
EN 61000-6-4, Emission industrial environments
EN 50121-4, Railway signalling and telecommunications apparatus
IEC 62236-4, Railway signalling and telecommunications apparatus
Safety UL/IEC/EN 60950-1, IT equipment
Marine DNV GL rules for classification – Ships and offshore units
FCC Part 15.105 Notice:
Corrosive environment
Notice:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
… Reorient or relocate the receiving antenna … Increase the separation between the equipment and receiver … Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected
… Consult the dealer or an experienced radio/TV technician for help.
This product has been successfully tested in a corrosion test according to IEC 60068- 2-60, method 3. This means that the product meets the requirements to be placed in an environment classified as ISA-S71.04 class G3.
Caution - Corrosive gases
If the product is placed in a corrosive environment, it is important that all unused connector sockets are protected with a suitable plug, in order to avoid corrosion attacks on the gold plated connector pins.
7
Type tests and environmental conditions
Environmental phenomena Basic standard Description Test levels
Electrostatic discharge EN 61000-4-2 Enclosure Contact: ±6 kV
Fast transients EN 61000-4-4 Power port ±2 kV
Surge EN 61000-4-5 Power port L-L: ±0.5 kV, 2 Ω, 18 μF
Power frequency magnetic field EN 61000-4-8 Enclosure 300 A/m; 0, 16.7, 60 Hz
Pulsed magnetic field EN 61000-4-9 Enclosure 300 A/m Radiated RF immunity EN 61000-4-3 Enclosure
Conducted RF immunity EN 61000-4-6 Power port 10 V, 80% AM, 1 kHz; (0.15 – 80) MHz
Radiated RF emission CISPR 16-2-3
Conducted RF emission CISPR 16-2-1
Dielectric strength EN 60950-1 Power port to all
ANSI C63.4 (FCC Part 15)
ANSI C63.4 (FCC Part 15b)
Ethernet Status out/Digital in Serial ports Enclosure
Ethernet L-E: ±2 kV, 2Ω, 0.5 μF Status out/Digital in L-E: ±2 kV, 42 Ω, 0.5 μF
RS-232 L-E: ±2 kV, 2 Ω, 0.5 μF RS-422/485 L-E: ±2 kV, 42 Ω, 0.5 μF
Ethernet Status out/Digital in Serial ports Earth port Enclosure Class B / DNV bridge
Power port Class B / DNV bridge Ethernet Class B
other ports Ethernet ports to all
other ports RS-232 port to all
other ports RS-422/485 port to all
other ports
Air: ±8 kV
L-E: ±2 kV, 42 Ω, 0.5 μF L-L: ±1 kV, 42 Ω, 0.5 μF L-E: ±2 kV, 12 Ω, 9 μF L-L: ±1 kV, 12 Ω, 9 μF
L-L: ±1 kV, 42 Ω, 0.5 μF
1000 A/m; 50 Hz
20 V/m @ (80 – 2700) MHz 10 V/m @ (2700 – 6000) MHz 1 kHz sine, 80% AM
1.5 kVrms, 50 Hz, 1 min
8
Loading...
+ 16 hidden pages
Buy Points How it Works FAQ Contact Us Questions and Suggestions Privacy Policy Cookie Policy Terms of Use