Westermo RFIR-227-F4G-T7G-DC, RFIR-127-F4G-T7G-AC, RFIR-219-F4G-T7G-DC, RFIR-219-F4G-T7G-AC, RFIR-227-F4G-T7G-AC User Manual

...

Download

Page 1

Industrial Routing Switch

www.westermo.com

Westermo Teleindustri AB

User Guide

6641-22810

RedFox

Industrial Rack

SERIES

WeOS

Status-

Status+

Digital In-

Digital In+

Page 2

6641-22810

Legal information

The contents of this document are provided “as is”. Except as required by applicable law, no warranties of any kind, either express or implied, including, but not limited to, the implied warranties of merchantability and fitness for a particular purpose, are made in relation to the accuracy and reliability or contents of this document. Westermo reserves the right to revise this document or withdraw it at any time without prior notice.

Under no circumstances shall Westermo be responsible for any loss of data or income or any special, incidental, and consequential or indirect damages howsoever caused. More information about Westermo can be found at the following Internet address:

http://www.westermo.com

Software tools

Related software tools are available in the folder software tools under technical support on the Westermo website.

Page 3

6641-22810

Safety

Before installation:

Read this manual completely and gather all information on the unit. Make sure that you understand it fully. Check that your application does not exceed the safe operating specifications for this unit. This unit should only be installed by qualified personnel. This unit should be built-in to an apparatus cabinet, or similar, where access is restricted to service personnel only. The power supply wiring must be sufficiently fused, and if necessary it must be possible to disconnect manually from the power supply. Ensure compliance to national installation regulations. This unit uses convection cooling. To avoid obstructing the airflow around the unit, follow the spacing recommendations (see Cooling section).

Before powering-up, a protective earthing conductor must be connected to the protective earthing terminal and have a cross-sectional area of at least 1.5 mm².

Before mounting, using or removing this unit:

Warning! Do not open connected unit. Hazardous voltage may occur within this unit when connected to power supply. Prevent access to hazardous voltage by disconnecting the unit from power supply.

Caution: Double pole/neutral fusing (AC models only)

Class 1 Laser Product. Do not look directly into fibre optical fibre port or

any connected fibre, although this unit is designed to meet the Class 1 Laser regulations. Complies with 21 CFR 1040.10 and 1040.11.

Caution: To reduce the risk of fire, use only No. 26 (e.g. 24 AWG) UL listed or CSA certified Telecommunication Line Cord.

Care recommendations

Follow the care recommendations below to maintain full operation of unit and to fulfil the warranty obligations. This unit must not be operating with removed covers or lids. Do not attempt to disassemble the unit. There are no user serviceable parts inside. Do not drop, knock or shake the unit, rough handling above the specification may cause damage to internal circuit boards. Do not use harsh chemicals, cleaning solvents or strong detergents to clean the unit. Do not paint the unit. Paint can clog the unit and prevent proper operation. Do not expose the unit to any kind of liquids (rain, beverages, etc). The unit is not waterproof. Keep the unit within the specified humidity levels. Do not use or store the unit in dusty, dirty areas, connectors as well as other mechanical part may be damaged. If the unit is not working properly, contact the place of purchase, nearest Westermo distributor office or Westermo Tech support. Fibre connectors are supplied with plugs to avoid contamination inside the optical port. As soon as no optical fibre is mounted on the connector, e.g. for storage, service or transportation, the plug should be applied.

! !

Page 4

6641-22810

Note. Fibre Optic Handling

Fibre optic equipment needs special treatment. It is very sensitive to dust and dirt. If the fibre will be disconnected from the unit the protective hood on the transmitter/receiver must be connected. The protective hood must be kept on during transportation. The fibre optic cable must also be handle the same way.

If these recommendations are not followed the warranty might be jeopardized.

Cleaning of the optical connectors

In the event of contamination, the optical connectors should only be cleaned by the use of recommended cleaning fluids and correct cleaning equipment.

Recommended cleaning fluids:

• Methyl-, ethyl-, isopropyl- or isobutyl-alcohol

• Hexane

• Naphtha

Maintenance

No maintenance is required, as long as the unit is used as intended within the specified conditions.

Page 5

6641-22810

Agency approvals and standards compliance

Art.no Model Type Approval/compliance

3641-4020 3641-4030 3641-4005 3641-4015 3641-4025 3641-4035

RFIR-127-F4G-T7G-DC RFIR-127-F4G-T7G-AC RFIR-219-F4G-T7G-DC RFIR-219-F4G-T7G-AC RFIR-227-F4G-T7G-DC RFIR-227-F4G-T7G-AC

EMC EN 50121-4, Railway applications –

Electromagnetic compatibility – Emission and immunity of the signalling and telecommunications apparatus

EN 55022, Information technology equipment – Radio disturbance characteristics – Limits and methods of measurement

EN 55024, Information technology equipment – Immunity characteristics Limits and methods of measurement

EN 61000-6-1, Electromagnetic compatibility – Immunity for residential environments

EN 61000-6-2, Electromagnetic compatibility – Immunity for industrial environments

EN 61000-6-4, Electromagnetic compatibility – Emission for industrial environments

IEC 62236-4, Railway signalling and

telecommunications apparatus Safety UL/IEC/EN 60950-1, IT equipment Marine DNV GL rules for classification – Ships and

offshore units

DNV GL rules for classification

Type Temperature Humidity Vibration EMC Enclosure

RFIR-xxx-F4G-T7G-AC C B A A A/IP40

RFIR-xxx-F4G-T7G-DC D B A B A/IP40

FCC Part 15.105 Notice:

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

EN 55022 Notice:

This is a class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures.

Page 6

6641-22810

Safety control drawing

Position

Direction/ description

Input/Output values

Status+ IO / Status + Uin = 60 VDC max

Status-- IO / Status – Iin = 80 mA max

Digital In+ IO / Digital in + Uin = 60 VDC max

Digital In- IO / Digital in – Iin = 2.9 mA max

Position

Direction/ description

Output values

1 In / VBUS

U = 5 VDC max I = 100 mA max

2 In/out / D–

3 In/out / D+

4 Not connected

5 Functional earth

Degree of protection: IP 40

Ambient temperature: –40 °C to +70 °C (DC), –40 °C to +55 °C (AC)

Position

Direction/ description

Input/output values

1 In/out / BI_DA+

Per port: U = ± 1 V (4V/us) I = ± 20 mA

Data rate: 10/100/1000 Mbit/s

2 In/out / BI_DA–

3 In/out / BI_DB+

4 In/out / BI_DC+

In/out / BI_DC–

6 In/out / BI_DB–

7 In/out / BI_DD+

8 In/out / BI_DD–

Shield Functional earth

Galvanically isolated via signal transformers and capacitively isolated to GND/Functional earth through a 2kV 1000pF capacitor. See user manual for proven transient protection.

Status-

Status+

Digital In-

Digital In+

Position

Direction/ description

Output values

1 Out / VBUS

out

= 5 VDC max

out

= 500 mA max

2 In/out / D–

3 In/out / D+

4 GND

Shield Functional earth

Direction/ description

Input values

In / +DC1

Uin = (16 – 60) VDC Iin = 2.0 A@16 VDC* PIn = 32 W@16 VDC*

In / +DC2

In / COM

DC Power supply AC Power supply

Direction/ description

Input values

In / P

Uin = (100–240) VAC, 50–60 Hz Iin = 360 mA@100 VAC**

In / N

In / NC

In /

+DC1

+DC2

COM

* RFIR-227-T7G-F4G-DC ** RFIR-227-T7G-F4G-AC

Page 7

6641-22810

Safety control drawing

Position Direction* / description Input/output values

Rx In / Receive port

Max 5 dBm

Tx Out / Transmit port

Position Direction* / description Input/output values

1 In/out / BI_DA+

Per port: U = ± 1 V (4V/us) I = ± 20 mA

Data rate: 100/1000 Mbit/s

2 In/out / BI_DA–

3 In/out / BI_DB+

4 In/out / BI_DC+

5 In/out / BI_DC–

6 In/out / BI_DB–

7 In/out / BI_DD+

8 In/out / BI_DD–

Shield Functional earth

Galvanically isolated via signal transformers and capacitively isolated to functional earth through a 2kV 1000pF capacitor. See user manual for proven transient protection.

* Direction relative this unit!

Position Direction* / description Input/output values

1 In/out / TD+

Per port: U = ± 1 V (4V/us) I = ± 20 mA

Data rate: 10/100 Mbit/s

2 In/out / TD–

3 In/out / RD+

4 Not connected

Not connected

6 In/out / RD–

7 Not connected

8 Not connected

Shield Functional earth

Galvanically isolated via signal transformers and capacitively isolated to functional earth through a 2kV 1000pF capacitor. See user manual for proven transient protection.

Page 8

6641-22810

Declaration of Conformity

Westermo Teleindustri AB

Declaration of Conformity

Org.nr/

Postadress/Postal address

Tel.

Telefax

Postgiro

Bankgiro

Corp. identity number Registered office

S-640 40 Stora Sundby 016-428000 016-428001 52 72 79-4 5671-5550 556361-2604 Eskilstuna

Sweden Int+46 16428000 Int+46 16428001

The manufacturer Westermo Teleindustri AB SE-640 40 Stora Sundby, Sweden

Herewith declares that the product(s)

Type of product Models1 Industrial Ethernet Switch for 19 inch Rack mounting

RFIR-x19-F4G-T7G-DC, RFIR-x27-F4G-T7G-DC RFIR-x19-F4G-T7G-AC, RFIR-x27-F4G-T7G-AC

is in conformity with the following EU directive(s).

No Short name 2014/30/EU Electromagnetic Compatibility (EMC)

2011/65/EU Restriction of the use of certain hazardous substances in electrical and electronic equipment

(RoHS)

2014/35/EU Low Voltage Directive (LVD)

Model Differences: x = 1 or 2 and indicates Software Class

References of standards applied for this EU declaration of conformity.

No Title Issue EN 50121-4 Railway applications – Electromagnetic compatibility – Emission and

immunity of the signalling and telecommunications apparatus

2015

EN 55022 Information technology equipment – Radio disturbance characteristics –

Limits and methods of measurement

2010

EN 55024 Information technology equipment – Immunity characteristics

Limits and methods of measurement

2010

EN 61000-6-1 Electromagnetic compatibility – Immunity for residential environments 2007 EN 61000-6-2 Electromagnetic compatibility – Immunity for industrial environments 2005

EN 61000-6-4 Electromagnetic compatibility – Emission for industrial environments 2007

+A1:2011

EN 50581 Technical documentation for the assessment of electrical and electronic

products with respect to the restriction of hazardous substances

2012

EN 60950-1 Information technology equipment - Safety - Part 1: General

requirements

2006 +A11: 2009 +A1: 2010 +A12: 2011 +A2: 2013

The last two digits of the year in which the CE marking was affixed: 16

Pierre Öberg Technical Manager 22

March 2016

Page 9

6641-22810

Type tests and environmental conditions

Phenomena Test Description Test levels

ESD EN 61000-4-2 Enclosure contact ± 6 kV

Enclosure air ± 8 kV

RF field AM modulated IEC 61000-4-3 Enclosure 20 V/m 80% AM (1 kHz), 80 – 2700 MHz

10 V/m 80% AM, 1kHz sine, 2700 – 6000 MHz

Fast transient EN 61000-4-4 Signal ports ± 2 kV

Power ports ± 2 kV

Surge EN 61000-4-5 Signal ports ± 2 kV line to earth, ± 1 kV line to line

Power ports ± 2 kV line to earth, ± 2 kV line to line

(AC models) ± 2 kV line to earth, ± 1 kV line to line (DC models)

RF conducted EN 61000-4-6 Signal ports 10 V 80% AM (1 kHz), 0.15 – 80 MHz

Power ports 10 V 80% AM (1 kHz), 0.15 – 80 MHz

Power frequency magnetic field

EN 61000-4-8 Enclosure 300 A/m 0, 16.7, 50, 60 Hz

Pulse magnetic field EN 61000-4-9 Enclosure 300 A/m Radiated emission CISPR 16-2-3 Enclosure Class A

ANSI C63.4 (FCC part 15)

Enclosure Class B, 30 – 6500 MHz

Conducted emission EN 55022 AC and DC power

ports Telecommunication ports Class B

Class B

FCC part 15 AC and DC power

ports

Class B

Dielectric strength EN 60950 Signal port to other

isolated ports

1.5 kVrms 50 Hz 1 min

Power port to other isolated ports

1.5 kVrms 50 Hz 1 min

Temperature EN 60068-2-1

EN 60068-2-2

Operating -40 to +70ºC (DC models)

-40 to +55ºC (AC models) Storage & Transport -40 to +85ºC (all models) Maximum surface

temperature

135 °C (temperature class T4)

Humidity EN 60068-2-30 Operating 5 to 95% relative humidity

Storage & Transport 5 to 95% relative humidity

Altitude Operating 2 000 m / 70 kPa Service life Operating 10 years Vibration IEC 60068-2-6 Operating 7.5 mm, 5 – 8 Hz

2 g, 8 – 500 Hz (19" rack mounting according to IEC 60297, DIN 41494)

Shock IEC 60068-2-27 Operating 15 g, 11 ms

(19" rack mounting according to IEC 60297, DIN 41494)

Enclosure UL 94 Aluminium / Zink Flammability class V-0 (all models)

Page 10

6641-22810

Description

The RFIR (RedFox Industrial Rack) is a high performance industrial Ethernet switch designed for high network traffic applications. Various port configurations are available that can be further customized with SFP transceivers. RFIR is powered by the Westermo WeOS network operating system.

RFIR is designed for 19” cabinet according to ETSI standard making it suitable for use in control room networks as well as for cabi¬nets installed along railway trackside or maritime installations. RFIR is designed to run efficiently from an AC or DC power supply, the unit is also equipped with configurable I/O fault contact that make it ideal for easy installation and monitoring in industrial applications.

RedFox Industrial Rack models

Westermo article number

Denomination Description

3641-4020 RFIR-127-F4G-T7G-DC

16 x 10/100 Mbit/s, Ethernet TX, RJ-45

7 x 10/100/1000 Mbit/s, Ethernet TX, RJ-45