Weslo WLEL33408.1 Owner's Manual
www.weslo.com
Model No. WLEL33408.1
Serial No.
Write the serial number in the
space above for reference.
Serial
Number
Decal
QUESTIONS?
If you have questions, or if parts are
damaged or missing, DO NOT
CONTACT THE STORE; please
contact Customer Care.
IMPORTANT: Please register this
product (see the limited warranty
on the back cover of this manual)
before contacting Customer Care.
USERʼS MANUAL
CALL TOLL-FREE:
1-866-699-3756
Mon.–Fri. 6 a.m.–6 p.m. MT
Sat. 8 a.m.–4 p.m. MT
ON THE WEB:
www.wesloservice.com
CAUTION
Read all precautions and instructions in this manual before using
this equipment. Keep this manual for future reference.
TABLE OF CONTENTS
ARNING DECAL PLACEMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
W
IMPORTANT PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
BEFORE YOU BEGIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
HOW TO USE THE ELLIPTICAL EXERCISER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
AINTENANCE AND TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
M
EXERCISE GUIDELINES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19
PART LIST . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20
EXPLODED DRAWING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22
ORDERING REPLACEMENT PARTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Back Cover
LIMITED WARRANTY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Back Cover
WARNING DECAL PLACEMENT
This drawing shows the location(s) of the
warning decal(s). If a decal is missing or
illegible, see the front cover of this
manual and request a free replacement
decal. Apply the decal in the location
shown. Note: The decal(s) may not be
shown at actual size.
2
IMPORTANT PRECAUTIONS
WARNING: To reduce the risk of serious injury, read all important precautions and
nstructions in this manual and all warnings on your elliptical exerciser before using your elliptical
i
exerciser. ICON assumes no responsibility for personal injury or property damage sustained by or
through the use of this product.
1. Before beginning any exercise program,
consult your physician. This is especially
important for persons over age 35 or persons with pre-existing health problems.
2. It is the responsibility of the owner to ensure
that all users of the elliptical exerciser are
adequately informed of all precautions.
3. Your elliptical exerciser is intended for home
use only. Do not use your elliptical exerciser
in a commercial, rental, or institutional setting.
4. Keep your elliptical exerciser indoors, away
from moisture and dust. Place your elliptical
exerciser on a level surface, with a mat
beneath it to protect the floor or carpet.
Make sure that there is enough clearance
around your elliptical exerciser to mount,
dismount, and use it.
5. Inspect and properly tighten all parts regularly. Replace any worn parts immediately.
6. Keep children under age 12 and pets away
from your elliptical exerciser at all times.
7. Your elliptical exerciser should not be used
by persons weighing more than 250 lbs.
(113 kg).
8. Wear appropriate exercise clothes when
exercising; do not wear loose clothes that
could become caught on your elliptical exerciser. Always wear athletic shoes for foot
protection.
9. Hold the handgrip pulse sensor or the upper
body arms when mounting, dismounting, or
using your elliptical exerciser.
10. Keep your back straight while using your
elliptical exerciser; do not arch your back.
11. The pulse sensor is not a medical device.
Various factors, including the userʼs movement, may affect the accuracy of heart rate
readings. The pulse sensor is intended only
as an exercise aid in determining heart rate
trends in general.
12. When you stop exercising, allow the pedals
to slowly come to a stop.
13. If you feel pain or dizziness while exercising,
stop immediately and cool down.
14. Use your elliptical exerciser only as
described in this manual.
3
BEFORE YOU BEGIN
hank you for selecting the revolutionary WESLO
T
PRO™ 13.8E elliptical exerciser. The 13.8E elliptical
exerciser provides an impressive selection of features
designed to make your workouts at home more effec-
ive and enjoyable.
t
For your benefit, read this manual carefully before
you use the elliptical exerciser. If you have ques-
tions after reading this manual, please see the front
Fan
Handlebar
over of this manual. To help us assist you, note the
c
product model number and serial number before contacting us. The model number and the location of the
serial number decal are shown on the front cover of
his manual.
t
Before reading further, please familiarize yourself with
the parts that are labeled in the drawing below.
Handgrip Pulse Sensor
Console
Water Bottle Holder*
Wheel
Adjustment Knob
*Water bottle is not included
Pedal
Pedal Disc
4
M10 x 112mm Carriage Bolt (34)–4
M10 x 88mm Button Screw (63)–2
M10 x 52mm Bolt Set (27)–2
M10 Split
Washer (70)–2
M8 Large
Washer (53)–10
Wave Washer
(95)–2
M8 Split
Washer (100)–4
M8 x 65mm Button Screw (99)–4
M8 x 50mm Button
Screw (89)–4
M10 Locknut
(29)–4
M8 Locknut
(46)–12
M4 x 16mm
Screw (66)–4
M4 x 22mm
Screw (91)–2
M8 x 25mm Patch
Screw (22)–2
M8 x 45mm Button
Bolt (50)–4
M8 x 38mm Button
Bolt (112)–4
ASSEMBLY
To hire an authorized service technician to assemble the elliptical exerciser, call 1-800-445-2480.
Assembly requires two persons. Place all parts of the elliptical exerciser in a cleared area and remove the
packing materials. Do not dispose of the packing materials until assembly is completed.
n addition to the included tool(s), assembly requires a Phillips screwdriver , an adjustable
I
wrench , and a rubber mallet .
As you assemble the elliptical exerciser, use the drawings below to identify small parts. The number in parentheses below each drawing is the key number of the part, from the PART LIST near the end of this manual. The
number following the parentheses is the quantity needed for assembly. Note: If a part is not in the hardware
kit, check to see if it has been preassembled.
5
1.
To make assembly easier, read the
information on page 5 before you begin
ssembling the elliptical exerciser.
a
dentify the Front Stabilizer (3). Make sure that
I
the Front Stabilizer is turned so that the
Wheels (32) are not touching the floor.
While another person lifts the front of the Frame
(1), attach the Front Stabilizer (3) to the Frame
with two M10 x 112mm Carriage Bolts (34) and
two M10 Locknuts (29).
1
34
32
32
3
1
29
29
2. While another person lifts the back of the
Frame (1), attach the Rear Stabilizer (4) to the
Frame with two M10 x 112mm Carriage Bolts
(34) and two M10 Locknuts (29).
2
29
29
1
4
34
6
3. While another person holds the Upright (2) in
the position shown, connect the Upper Wire
Harness (86) to the Lower Wire Harness (87).
3
Tip: Avoid pinching the Wire Harnesses (86,
87). Insert the Upright (2) into the Frame (1).
Next, slide an M10 Split Washer (70) and a
Frame Spacer (83) onto each of the two M10 x
8mm Button Screws (63).
8
Insert the M10 x 88mm Button Screws (63) into
the Frame (1) and the Upright (2). Make sure
that the concave sides of the Frame Spacers
(83) are facing the Frame. Do not tighten the
Button Screws yet.
Attach the Water Bottle Holder (105) to the
Upright (2) with two M4 x 22mm Screws (91).
4. Identify the Left Pulse Bar (107), which is
marked with a “Left” sticker.
Have another person hold the Left Pulse Bar
(107) near the left side of the Upright (2). Make
sure that the hexagonal holes are in the
indicated location.
See the inset drawing. Locate the wire tie in
the Upright (2). Tie the lower end of the wire tie
to the left Pulse Wire (113). Next, pull the upper
end of the wire tie upward out of the top of the
Upright. Then, untie and discard the wire tie.
Tip: Avoid pinching the wires. Slide the Left
Pulse Bar (107) onto the Upright (2). Attach the
Left Pulse Bar with two M8 x 38mm Button
Bolts (112) and two M8 Locknuts (46). Make
sure that the Locknuts are in the hexagonal
holes.
63
4
107
Hexagonal
112
Holes
Wire Tie
2
70
83
70
83
Wire Ties
113
46
113
Do not pinch the Wire
Harnesses (86, 87)
105
91
86
87
1
113
108
86
2
Avoid pinching
the wires
Repeat this step for the Right Pulse Bar
(108).
7
5. The Console (5) can use four 1.5V “D” batteries
(not included); alkaline batteries are recommended. IMPORTANT: If the Console has
been exposed to cold temperatures, allow it
to warm to room temperature before inserting batteries. Otherwise, you may damage
the console displays or other electronic
components. Remove the battery cover, insert
he batteries into the battery compartment, and
t
reattach the battery cover. Make sure to orient
the batteries as shown by the diagram inside
the battery compartment.
To purchase an optional AC adapter, contact
the store where you purchased this product
or call the telephone number on the cover of
this manual. To avoid damaging the console,
use only a manufacturer-supplied AC
adapter. Plug one end of the AC adapter into
the jack on the console; plug the other end into
an outlet installed in accordance with all local
codes and ordinances.
5
Battery
Cover
Batteries
5
6. While another person holds the Console (5)
near the Upright (2), connect the console wire
to the Upper Wire Harness (86). Then, connect
the console pulse wires to the Pulse Wires
(113). Insert the excess wire downward into the
Upright.
Tip: Avoid pinching the wires. Attach the
Console (5) to the Upright (2) with four M4 x
16mm Screws (66).
6
5
66
Console
Wire
86
2
113
Pulse
Wires
8
Loading...