This drawing shows the location(s) of the
warning decal(s). If a decal is missing
or illegible, call the telephone number
on the front cover of this manual and
request a free replacement decal.
Apply the decal in the location shown.
Note: The decal(s) may not be shown at
actual size.
WESLO is a registered trademark of ICON IP, Inc.
2
IMPORTANT PRECAUTIONS
WARNING: To reduce the risk of serious injury, read all important precautions and
instructions in this manual and all warnings on your elliptical exerciser before using your elliptical
exerciser. ICON assumes no responsibility for personal injury or property damage sustained by or
hrough the use of this product.
t
1. Before beginning any exercise program,
consult your physician. This is especially
important for persons over the age of 35 or
persons with pre-existing health problems.
2. It is the responsibility of the owner to ensure
that all users of the elliptical exerciser are
adequately informed of all precautions.
3. Your elliptical exerciser is intended for home
use only. Do not use your elliptical exerciser
in a commercial, rental, or institutional setting.
4. Keep your elliptical exerciser indoors, away
from moisture and dust. Place your elliptical
exerciser on a level surface, with a mat
beneath it to protect the floor or carpet.
Make sure that there is at least 3 ft. (1 m) of
clearance in the front and rear of your elliptical exerciser and 2 ft. (0.6 m) on each side.
5. Inspect and properly tighten all parts regularly. Replace any worn parts immediately.
8. Wear appropriate exercise clothes when
exercising; do not wear loose clothes that
could become caught on your elliptical exerciser. Always wear athletic shoes for foot
protection.
9. Hold the handlebars when mounting, dismounting, or using your elliptical exerciser.
10. Keep your back straight while using your
elliptical exerciser; do not arch your back.
11. The pulse sensor is not a medical device.
Various factors, including the userʼs movement, may affect the accuracy of heart rate
readings. The pulse sensor is intended only
as an exercise aid in determining heart rate
trends in general.
12. When you stop exercising, allow the pedals
to slowly come to a stop.
13. If you feel pain or dizziness while exercising,
stop immediately and cool down.
6. Keep children under age 12 and pets away
from your elliptical exerciser at all times.
7. Your elliptical exerciser should not be used
by persons weighing more than 250 lbs.
(113 kg).
14. Use your elliptical exerciser only as
described in this manual.
3
BEFORE YOU BEGIN
Thank you for selecting the new WESLO®MOMENTUM
T 3.8 elliptical exerciser. The MOMENTUM CT 3.8
C
provides a selection of features designed to make
your workouts at home more effective and enjoyable.
For your benefit, read this manual carefully before
you use the elliptical exerciser. If you have ques-
tions after reading this manual, please see the front
cover of this manual. To help us assist you, note the
product model number and serial number before con-
Resistance Knob
tacting us. The model number and the location of the
erial number decal are shown on the front cover of
s
this manual.
To avoid a registration fee for any service needed
under warranty, you must register the elliptical
exerciser at www.wesloservice.com/registration.
Before reading further, please familiarize yourself with
the parts that are labeled in the drawing below.
Console
Handlebar
Shield
Pedal Disc
Pedal
4
M10
Washer (35)–2
M10 Split
Washer (59)–2
M10 Locknut
(33)–6
Pedal Arm Bolt Set (40)–2
M6 Locknut
(27)–4
M10 x 25mm
Patch Screw (22)–2
M10 x 75mm Carriage Bolt (34)–4M10 x 68mm Button Bolt (48)–2
M6 x 38mm Button Bolt (50)–4
M6 x 45mm Flat Head
Screw (36)–4
Wave Washer
(64)–2
M4 x 16mm
Screw (42)–4
ASSEMBLY
To hire an authorized service technician to assemble the elliptical exerciser, call 1-800-445-2480.
ssembly requires two persons. Place all parts of the elliptical exerciser in a cleared area and remove the
A
packing materials. Do not dispose of the packing materials until assembly is completed.
In addition to the included tool(s), assembly requires a Phillips screwdriver, an adjustable
wrench, and pliers.
See the drawings below to identify the small parts needed for assembly. The number in parentheses below
each drawing is the key number of the part, from the PART LIST near the end of this manual. The number following the key number is the quantity needed for assembly. Note: Some small parts may have been
preassembled. If a part is not in the hardware kit, check to see if it has been preassembled.
5
1.
To make assembly easier, read the
information on page 5 before you begin.
1
34
Identify the Front Stabilizer (10), which is narrower than the Rear Stabilizer (not shown).
While another person lifts the front of the Frame
(1), attach the Front Stabilizer (10) to the Frame
with two M10 x 75mm Carriage Bolts (34) and
two M10 Locknuts (33).
2. While another person lifts the back of the Frame
(1), attach the Rear Stabilizer (28) to the Frame
with two M10 x 75mm Carriage Bolts (34) and
two M10 Locknuts (33).
33
10
1
33
2
33
28
3. The Console (23) requires four “AA” batteries
(not included); alkaline batteries are recommended. Remove the screw, remove the battery
cover, and then insert four batteries into the battery compartment. Make sure that the
batteries are oriented as shown by the diagram inside the battery compartment. Then,
reattach the battery cover.
33
1
34
3
Screw
Battery
Cover
Batteries
23
6
Loading...
+ 14 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.