Weslo WLEL28020 User Manual

CAUTION

Read all precautions and instruc­tions in this manual before using
this equipment. Keep this manu­al for future reference.

Model No. WLEL28020
Serial No.

QUESTIONS?

If you have questions, or if there
are missing parts, we will guar­antee complete satisfaction
through direct assistance from
our factory.

TO AVOID DELAYS, PLEASE
CALL DIRECT TO OUR TOLL­FREE CUSTOMER HOT LINE. The
technicians on our customer hot
line will provide immediate assis­tance, free of charge to you.

CUSTOMER HOT LINE:

1-800-999-3756

Mon.–Fri., 6 a.m.–6 p.m. MST

Visit our website at

www.weslo.com

new products, prizes,

fitness tips, and much more!

USER’S MANUAL

Serial Number

Decal

TABLE OF CONTENTS

IMPORTANT PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3

BEFORE YOU BEGIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4

ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5

HOW TO USE THE ELLIPTICAL CROSSTRAINER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9

MAINTENANCE AND TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11

CONDITIONING GUIDELINES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13

PART LIST . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14

EXPLODED DRAWING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15

HOW TO ORDER REPLACEMENT PARTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Back Cover

LIMITED WARRANTY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Back Cover

2

WESLO is a registered trademark of ICON Health & Fitness, Inc.

3

IMPORTANT PRECAUTIONS

WARNING:To reduce the risk of serious injury, read the following important precau-

tions before using the elliptical crosstrainer.

1. Read all instructions in this manual before
using the elliptical crosstrainer. Use the
elliptical crosstrainer only as described.

2. It is the responsibility of the owner to ensure
that all users of the elliptical crosstrainer
are adequately informed of all precautions.

3. Place the elliptical crosstrainer on a level
surface, with a mat beneath it to protect the
floor or carpet. Keep the elliptical crosstrain­er indoors, away from moisture and dust.

4. Inspect and properly tighten all parts regu­larly. Replace any worn parts immediately.

5. Keep children under 12 and pets away from
the elliptical crosstrainer at all times.

6. The elliptical crosstrainer should not be used
by persons weighing more than 250 pounds.

7. Wear appropriate exercise clothing when
using the elliptical crosstrainer. Always wear
athletic shoes for foot protection.

8. Always hold the handlebars when mounting,
dismounting, or using the elliptical
crosstrainer.

9. Keep your back straight when using the ellip­tical crosstrainer. Do not arch your back.

10. If you feel pain or dizziness while exercis­ing, stop immediately and cool down.

11. When you stop exercising, allow the pedals
to slowly come to a stop.

12. The elliptical crosstrainer is intended for
home use only. Do not use the elliptical
crosstrainer in a commercial, rental, or insti­tutional setting.

WARNING:

Before beginning this or any exercise program, consult your physician.
This is especially important for persons over the age of 35 or persons with pre-existing health prob­lems. Read all instructions before using. ICON assumes no responsibility for personal injury or
property damage sustained by or through the use of this product.

4

BEFORE YOU BEGIN

Congratulations for selecting the new WESLO

®

MOMENTUM 750 elliptical crosstrainer. The MOMEN­TUM 750 elliptical crosstrainer is an incredibly smooth
exerciser that moves your feet in a natural elliptical
path, minimizing the impact on your knees and
ankles. And the unique MOMENTUM 750 features
adjustable resistance and a simple-to-use console to
help you get the most from your exercise.

For your benefit, read this manual carefully before
using the elliptical crosstrainer. If you have ques-

tions after reading this manual, please call our

Customer Service Department toll-free at 1-800-999­3756, Monday through Friday, 6 a.m. until 6 p.m.
Mountain Time (excluding holidays). To help us assist
you, please note the product model number and serial
number before calling. The model number is
WLEL28020. The serial number is found on a decal
attached to the elliptical crosstrainer (see the front
cover of this manual for the location of the decal).

Before reading further, please familiarize yourself with
the parts that are labeled in the drawing below.

Handlebar

FRONT

BACK

Pedal Arm

Pedal Disk

*No water bottle is included

Pedal

Console

Water Bottle Holder*

Resistance Knob

5

ASSEMBLY

Assembly requires two persons. Place all parts of the elliptical crosstrainer in a cleared area and remove the
packing materials. Do not dispose of the packing materials until assembly is completed. In addition to the
included allen wrenches, assembly requires a phillips screwdriver , an adjustable
wrench , and a rubber mallet .

As you assemble the elliptical crosstrainer, use the drawings below to identify the small parts used in assembly.
The number in parenthesis below each drawing refers to the key number of the part, from the PART LIST on
page 14. The second number refers to the quantity used in assembly. Note: Some small parts may have been

pre-assembled for shipping. If a part is not in the parts bag, check to see if it has been pre-assembled.

1. Identify the Front Stabilizer (10), which is narrower than
the Rear Stabilizer (not shown). While another person
lifts the front of the Frame (1), attach the Front
Stabilizer to the Frame with two M10 x 75mm Carriage
Bolts (34) and two M10 Nylon Locknuts (33).

10

33

34

1

1

M6 Nylon

Locknut (27)–4

M10

Washer (35)–2

M8 x 38mm Button Bolt (50)–4

Locknut (38)–4

M4 x 16mm

Screw (42)–4

M8 Nylon

M10 Nylon

Locknut (33)–6

M6 x 54mm Flat Head

Bolt (36)–4

Pedal Arm Bolt Set (40)–2

M10 x 75mm Carriage Bolt (34)–4M10 x 66mm Button Bolt (48)–2

M6

Washer (25)–4

M10 Split

Washer (59)–2

M10 x 25mm

Patch Screw (22)–2

6

2. While another person lifts the back of the Frame (1),

attach the Rear Stabilizer (28) to the Frame with two
M10 x 75mm Carriage Bolts (34) and two M10 Nylon
Locknuts (33).

34

28

1

2

33

33

3. The Console (23) requires three “AA” batteries (not

included); alkaline batteries are recommended. Insert
three batteries into the battery compartment. Make

sure that the batteries are oriented as shown by
the diagram inside the battery compartment.

23

Batteries

3

4. While another person holds the Console (23) near the

Upright (2), connect the console wire to the Upper
Wire (44). Insert the console wire and the Upper Wire
into the Upright.

Attach the Console (23) to the Upright (2) with four M4
x 16mm Screws (42). Be careful to avoid pinching

the console wire or the Upper Wire (44).

Turn the Resistance Knob (63) counterclockwise to
the lowest setting before continuing to the next
step.

4

23

2

44

63

Console Wire

42

5

1

2

33

Make sure that

the wires and
cables do not

get pinched

and damaged

during this

step.

44

53

48

55

63

59

5. While another person holds the Upright (2) near the

Frame (1), connect the Upper Wire (44) to the Reed
Switch Wire (53).

Next, connect the Resistance Cable (63) to the Lower
Cable (55) in the following way:

• Refer to drawing A. Pull up on the metal bracket on
the Lower Cable (55), and insert the tip of the
Resistance Cable (63) into the wire clip inside of the
metal bracket.

• Refer to drawing B. Firmly pull the Resistance Cable
(63) and slide it into the metal bracket on the Lower
Cable (55) as shown.

• Refer to drawing C. Using pliers, squeeze together
the prongs on the upper end of the metal bracket.

Push the excess cable and wire down into the Frame
(1). Slide the Upright (2) onto the Frame. Be careful
not to pinch the wires or cables. Secure the Upright
to the Frame with two M10 x 66mm Button Bolts (48),
two M10 Split Washers (59), and two M10 Nylon
Locknuts (33). Do not tighten the Button Bolts yet.

55

55

Metal

Bracket

B

A

C

55

63

63

63

50

8

38

7

6. Identify the Left Handlebar (6), which is marked with a
sticker. Insert the Left Handlebar into one of the
Handlebar Arms (5); make sure that the Handlebar

Arm is turned so the hexagonal holes are on the
indicated side. Attach the Left Handlebar to the

Handlebar Arm with two M8 x 38mm Button Bolts (50)
and two M8 Nylon Locknuts (38). Make sure that the

Nylon Locknuts are inside of the hexagonal holes.
Do not fully tighten the Button Bolts yet.

Apply a small amount of the included grease to the left
axle on the Upright (2).

Make sure that there are two Small Handlebar
Bushings (49) in the Left Handlebar (6). Slide a
Handlebar Spacer (47) and the Left Handlebar onto the
left axle on the Upright (2) as shown. Make sure that the

Handlebar Spacer is turned so the curved side is fac­ing the Upright. Tap an Axle Cap (14) onto the axle.

Repeat this step to assemble the Right Handlebar (8)
and the other Handlebar Arm (5).

Grease

6

47

14

49

5

2

5

6

7

36

27

25

11

13

7. Identify the Left Pedal Arm (11). Attach a Pedal (13) to
the Left Pedal Arm with two M6 x 54mm Flat Head
Bolts (36), two M6 Washers (25), and two M6 Nylon
Locknuts (27) as shown.

Attach the other Pedal to the Right Pedal Arm (not
shown) in the same way.

Hexagonal

Holes

8

9. Make sure that all parts of the elliptical crosstrainer are properly tightened. Note: Some hardware may
be left over after assembly is completed. To protect the floor or carpet from damage, place a mat under the
elliptical crosstrainer.

8. Apply a small amount of grease to the axle on the left
Disc Crossbar (16). Slide the Left Pedal Arm (11) onto
the axle. Slide an M10 Washer (35) onto an M10 x
25mm Patch Screw (22), and tighten the Patch Screw
into the axle.

Next, hold the lower end of the left Handlebar Arm (5)
inside of the bracket on the Left Pedal Arm (11). Apply
grease to a Pedal Arm Bolt Set (40). Attach the Left
Pedal Arm to the left Handlebar Arm with the Bolt Set.

Do not overtighten the Bolt Set; the Handlebar Arm
must pivot freely.

Attach the Right Pedal Arm (not shown) to the right
side of the elliptical crosstrainer in the same way.

Refer to step 5. Tighten the M10 x 66mm Button Bolts
(48) in the Upright (2).

Refer to step 6. Tighten the M8 x 38mm Button Bolts
(50) in the Handlebar Arms (5).

Grease

Grease

22

35

11

5

8

16

40

40

9

HOW TO USE THE ELLIPTICAL CROSSTRAINER

HOW TO EXERCISE ON THE ELLIPTICAL
CROSSTRAINER

To mount the elliptical crosstrainer, hold the handlebars
and step onto the pedal that is in the lowest position.
Then, step onto the other pedal. Push the pedals until
they begin to move with a continuous motion. Note:

The pedal disks can turn in either direction. It is
recommended that you move the pedal disks in
the direction shown by the arrow; however, for
variety, you may turn the pedal disks in the oppo­site direction.

To dismount the elliptical crosstrainer, wait until the
pedals come to a complete stop. Note: The elliptical

crosstrainer does not have a free wheel; the ped­als will continue to move until the flywheel stops.

When the pedals are stationary, step off the highest
pedal first. Then, step off the lowest pedal.

HOW TO ADJUST THE PEDALING RESISTANCE

As you exercise,
you can adjust the
resistance of the
pedals with the
resistance knob on
the upright. To
increase the resis­tance, turn the
knob clockwise; to
decrease the resis­tance, turn the
knob counterclock­wise.

Pedal Disk

Pedal

Handlebars

Resistance

Knob

10

FEATURES OF THE CONSOLE

The easy-to-use console features five modes that pro­vide instant exercise feedback during your workouts.
The modes are described below.

Speed—This mode displays your pedaling speed, in
miles per hour or kilometers per hour.

Time—This mode displays the elapsed time. Note: If
you stop pedaling for a few seconds, the time mode
will pause.

Distance—This mode displays the distance you have
pedaled, in miles or kilometers.

Calorie—This mode displays the approximate number
of calories you have burned.

Scan—This mode displays the speed, time, distance,
and calorie modes, for a few seconds each, in a
repeating cycle.

HOW TO OPERATE THE CONSOLE

Make sure there are batteries in the console (see
BATTERY REPLACEMENT on page 11). If there is a
thin sheet of clear plastic on the console, remove it.

Follow the steps below to operate the console.

1. To turn on the power, press the On/Reset button or

begin pedaling. The entire display will briefly
appear; the console will then be ready for use.

2. Select one of the modes:
Scan mode—

When the power
is turned on, the
scan mode will be
selected automati­cally. A mode indi­cator will appear
below the word
“SCAN” to show
that the scan
mode is selected,
and a second
mode indicator will show which mode is currently
displayed. Note: If you have selected a different
mode, repeatedly press the Mode button to rese­lect the scan mode.

Speed, time, dis­tance, or calorie
mode—To select

one of these
modes for continu­ous display,
repeatedly press
the Mode button.
The mode indica­tors will show
which mode is selected. Make sure there is not a
mode indicator below the word “SCAN.”

Note: The console can display speed and dis­tance in either miles or kilometers. T o change
the unit of measurement, press the On/Reset
button for about five seconds. The letters mph or

km/h will appear in the display to show which unit of
measurement is selected. When the batteries are
replaced, it may be necessary to reselect the
desired unit of measurement.

3. To reset the display at any time, press the

On/Reset button.

4. To turn off the power, simply wait for a few minutes.

The console has an “auto-off” feature. If the
pedals are not moved and the console buttons
are not pressed for a few minutes, the power
will turn off automatically to save the batteries.

Mode Indicators

11

Inspect and tighten all parts of the elliptical crosstrainer
regularly. Replace any worn parts immediately.

To clean the elliptical crosstrainer, use a damp cloth
and a small amount of mild soap. Important: Keep

liquids away from the console, place only a sealed
water bottle in the water bottle holder, and keep
the console out of direct sunlight. During storage,
remove the batteries from the console.

BATTERY REPLACEMENT

If the console display becomes dim, the batteries
should be replaced; most console problems are the
result of low batteries. To replace the batteries, refer
to step 4 on page 6 and remove the console from the
upright. Next, refer to step 3 on page 6 and insert
three batteries into the console. Reattach the console
to the upright, being careful not to pinch the wires.

HOW TO ADJUST THE REED SWITCH

If the console does not display correct feedback, the
reed switch should be adjusted. To adjust the reed
switch, you must remove the Left Pedal Arm (11) and
the Left Side Shield (3).

Remove the Pedal Arm Bolt Set (40), the M10 x
25mm Patch Screw (22), and the M10 Washer (35)
from the Left Pedal Arm (11). Remove the Left Pedal
Arm. Next, remove the two M4 x 25mm Screws (56)
and the four M4 x 16mm Screws (42) from the Left
Side Shield (3).

Refer to the drawing below and locate the Reed Switch
(53). Loosen, but do not remove, the indicated M4 x
16mm Screw (42). Slide the Reed Switch slightly
toward or away from the Magnet (58) on the flywheel.
Retighten the Screw. Turn the left Pedal Disc (15) for a
moment. Repeat until the console displays correct
feedback. When the Reed Switch is correctly adjusted,
reattach the Left Side Shield (3) and the Left Pedal
Arm (11).

HOW TO ADJUST THE DRIVE BELT

If the pedals slip while you are pedaling, even when
the resistance is adjusted to the highest setting, the
Drive Belt (19) may need to be adjusted. To adjust the
Drive Belt, you must first remove the left side shield.
Refer to HOW TO ADJUST THE REED SWITCH at
the left and remove the left side shield.

Next, loosen the
M8 x 22mm Flat
Head Screw
(41) and turn
the Idler
Adjustment Bolt
(62) until the
Drive Belt (19)
is tight. When
the Drive Belt is
tight, tighten the
Flat Head
Screw. Reattach
the left side shield.

MAINTENANCE AND TROUBLESHOOTING

42

56

42

42

22

35

3

40

15

41

62

19

11

58

53

42

12

HOW TO ADJUST THE RESISTANCE STRAP

If the resistance knob is turned to the highest setting
and there is not enough pedaling resistance, the
resistance strap can be adjusted. To adjust the resis­tance strap, first remove the left side shield (see HOW
TO ADJUST THE REED SWITCH on page 11).

Next, turn the resistance knob to the lowest setting.
Open the Strap Clamp (26) and pull the end of the
Resistance Strap (18) downward slightly. Close the
Strap Clamp and turn the Flywheel (17) to make sure
that there is not too much resistance.

When the resistance strap is properly adjusted, re­attach the left side shield and the left pedal arm.

18

17

26

13

CONDITIONING GUIDELINES

The following guidelines will help you to plan your
exercise program. Remember that proper nutrition
and adequate rest are essential for successful results.

EXERCISE INTENSITY

Whether your goal is to burn fat or to strengthen your
cardiovascular system, the key to achieving the
desired results is to exercise with the proper intensity.
The proper intensity level can be found by using your
heart rate as a guide. The chart below shows recom­mended heart rates for fat burning, maximum fat
burning, and cardiovascular (aerobic) exercise.

To find the proper heart rate for you, first find your age
at the bottom of the chart (ages are rounded off to the
nearest ten years). Next, find the three numbers above
your age. The three numbers are your “training zone.”
The lowest number is the recommended heart rate for
fat burning; the middle number is the recommended
heart rate for maximum fat burning; the highest num­ber is the recommended heart rate for aerobic exer­cise.

Fat Burning

To burn fat effectively, you must exercise at a relative­ly low intensity level for a sustained period of time.
During the first few minutes of exercise, your body
uses easily accessible carbohydrate calories for ener-
gy. Only after the first few minutes of exercise does
your body begin to use stored fat calories for energy.
To burn fat, adjust the intensity of your exercise until
your heart rate is between the lower two numbers in
your training zone as you exercise.

Aerobic Exercise

If your goal is to strengthen your cardiovascular sys­tem, your exercise must be “aerobic.” Aerobic exer­cise is activity that requires large amounts of oxygen
for prolonged periods of time. This increases the
demand on the heart to pump blood to the muscles,
and on the lungs to oxygenate the blood. For aerobic
exercise, adjust the intensity of your exercise until
your heart rate is near the highest number in your
training zone.

HOW TO MEASURE YOUR HEART RATE

Exercise for at least
four minutes. Then,
stop exercising and
place two fingers on
your wrist as shown.
Take a six-second
heartbeat count, and
multiply the result by
10 to find your heart
rate. For example, if your six-second heartbeat count
is 14, your heart rate is 140 beats per minute. (A six­second count is used because your heart rate will
drop rapidly when you stop exercising.)

WORKOUT GUIDELINES

Each workout should include the following three parts:
A warm-up, consisting of 5 to 10 minutes of stretching

and light exercise. A proper warm-up increases your
body temperature, heart rate, and circulation in prepa­ration for exercise.

Training zone exercise, consisting of 20 to 30 min­utes of exercising with your heart rate in your training
zone. Note: During the first few weeks of your exer­cise program, do not keep your heart rate in your
training zone for longer than 20 minutes.

A cool-down, with 5 to 10 minutes of stretching. This
will increase the flexibility of your muscles and will
help to prevent post-exercise problems.

EXERCISE FREQUENCY

To maintain or improve your condition, plan three work­outs each week, with at least one day of rest between
workouts. After a few months of regular exercise, you
may complete up to five workouts each week, if
desired. The key to success is make exercise a regu­lar and enjoyable part of your everyday life.

WARNING:Before beginning

this or any exercise program, consult your
physician. This is especially important for
persons over the age of 35 or persons with
pre-existing health problems.

14

Note: # indicates a non-illustrated part. Specifications are subject to change without notice.

Key No. Qty. Description Key No. Qty. Description

PART LIST—Model No. WLEL28020 R0802A

1 1 Frame
2 1 Upright
3 1 Left Side Shield
4 1 Right Side Shield
5 2 Handlebar Arm
6 1 Left Handlebar
7 1 Idler Assembly
8 1 Right Handlebar

9 1 Hook
10 1 Front Stabilizer
11 1 Left Pedal Arm
12 1 Right Pedal Arm
13 2 Pedal
14 2 Axle Cap
15 2 Pedal Disc
16 2 Disc Crossbar
17 1 Flywheel
18 1 Resistance Strap
19 1 Drive Belt
20 1 Cable Clamp
21 4 Endcap
22 2 M10 x 25mm Patch Screw
23 1 Console
24 2 Handgrip
25 4 M6 Washer
26 1 Strap Clamp
27 4 M6 Nylon Locknut
28 1 Rear Stabilizer
29 2 Flywheel Bearing
30 2 Large Snap Ring
31 2 Large Bearing
32 1 Pedal Axle
33 7 M10 Nylon Locknut

34 4 M10 x 75mm Carriage Bolt
35 2 M10 Washer
36 4 M6 x 54mm Flat Head Bolt
37 4 Pedal Arm Bushing
38 5 M8 Nylon Locknut
39 2 M10 Washer
40 2 Pedal Arm Bolt Set
41 1 M8 x 22mm Flat Head Screw
42 15 M4 x 16mm Screw
44 1 Upper Wire
45 1 Resistance Control/Cable
46 2 Handlebar Cap
47 2 Handlebar Spacer
48 2 M10 x 66mm Button Bolt
49 4 Small Handlebar Bushing
50 4 M8 x 38mm Button Bolt
51 8 M6 x 35mm Screw
52 1 M4 x 16mm Flat Head Screw
53 1 Reed Switch/Wire
54 1 Cable Clamp
55 1 Lower Cable
56 2 M4 x 25mm Screw
57 1 M10 Flat Head Bolt
58 1 Magnet
59 2 M10 Split Washer
60 4 Large Handlebar Bushing
61 2 5/16” x 25.4mm Hex Bolt
62 1 Idler Adjustment Bolt
63 1 Resistance Knob/Cable

# 1 Allen Wrench
# 1 Grease
# 1 User’s Manual

EXPLODED DRAWING—Model No. WLEL28020 R0802A

15

50

46

5

60

60

38

6

14

49

24

44

42

49

47

33

21

24

2

47

59

59

49

23

42

63

48

45

38

60

8

49

42

14

60

42

46

5

17

50

3

39

40

56

42

20

40

12

42

25

18

27

36

25

42

27

42

37

13

4

35

51

42

42

22

37

40

21

11

40

19

25

35

34

27

22

36

37

51

51

13

15

10

51

37

42

55

53

61

54

33

16

52

41

31

30

57

39

26

33

29

32

7

62

1

58

21

38

29

33

31

33

30

16

33

9

61

21

28

51

15

34

Part No. 189690 R0802A Printed in China © 2002 ICON Health & Fitness, Inc.

HOW TO ORDER REPLACEMENT PARTS

To order replacement parts, simply call our Customer Service Department toll-free at 1-800-999-3756, Monday
through Friday, 6 a.m. until 6 p.m. Mountain Time (excluding holidays). To help us assist you, please be
prepared to give the following information when calling:

• The MODEL NUMBER of the product (WLEL28020)

• The NAME of the product (WESLO

®

MOMENTUM 750 elliptical crosstrainer)

• The SERIAL NUMBER of the product (see the front cover of this manual)

• The KEY NUMBER and DESCRIPTION of the part(s) (see page 14)

LIMITED WARRANTY

ICON Health & Fitness, Inc. (ICON), warrants this product to be free from defects in workmanship and
material, under normal use and service conditions, for a period of ninety (90) days from the date of pur­chase. This warranty extends only to the original purchaser. ICON's obligation under this warranty is lim­ited to replacing or repairing, at ICON's option, the product through one of its authorized service centers.
All repairs for which warranty claims are made must be pre-authorized by ICON. This warranty does not
extend to any product or damage to a product caused by or attributable to freight damage, abuse, mis­use, improper or abnormal usage or repairs not provided by an ICON authorized service center; products
used for commercial or rental purposes; or products used as store display models. No other warranty
beyond that specifically set forth above is authorized by ICON.

ICON is not responsible or liable for indirect, special or consequential damages arising out of or in con­nection with the use or performance of the product or damages with respect to any economic loss, loss
of property, loss of revenues or profits, loss of enjoyment or use, costs of removal or installation or other
consequential damages of whatsoever nature. Some states do not allow the exclusion or limitation of inci­dental or consequential damages. Accordingly, the above limitation may not apply to you.

The warranty extended hereunder is in lieu of any and all other warranties and any implied warranties of
merchantability or fitness for a particular purpose is limited in its scope and duration to the terms set forth
herein. Some states do not allow limitations on how long an implied warranty lasts. Accordingly, the above
limitation may not apply to you.

This warranty gives you specific legal rights. You may also have other rights which vary from state to state.

ICON HEALTH & FITNESS, INC., 1500 S. 1000 W., LOGAN, UT 84321-9813