Weslo Cadence Ex14 User Manual

¨

USER'S MANUAL

QUESTIONS?

As a manufacturer, we are
committed to providing complete
customer satisfaction. If you
have questions, or if there are
missing parts, we will guarantee
complete satisfaction through
direct assistance from our factory.

TO AVOID UNNECESSARY
DELAYS, PLEASE CALL DIRECT
TO OUR TOLL-FREE CUSTOMER
HOT LINE. The trained techni­cians on our customer hot line
will provide immediate assis­tance, free of charge to you.

CUSTOMER HOT LINE:

1-800-999-3756

Mon.ÐFri., 6 a.m.Ð6 p.m. MST

Model No. WLTL29200
Serial No.

Write the serial number in the
space above for future reference.

CAUTION

Read all precautions and instruc­tions in this manual before using
this equipment. Save this manual
for future reference.

Serial

Number

Decal

Visit our website at

www.weslo.com

new products, prizes,

fitness tips, and much more!

2

TABLE OF CONTENTS

IMPORTANT PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

BEFORE YOU BEGIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

OPERATION AND ADJUSTMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

HOW TO FOLD AND MOVE THE TREADMILL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10

MAINTENANCE AND TROUBLE-SHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12

CONDITIONING GUIDELINES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

ORDERING REPLACEMENT PARTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Back Cover

LIMITED WARRANTY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Back Cover

Note: A PART LIST and an EXPLODED DRAWING are attached in the center of this manual.

1. It is the responsibility of the owner to ensure
that all users of this treadmill are adequately
informed of all warnings and precautions.

2. Use the treadmill only as described in this
manual.

3. Place the treadmill on a level surface, with at
least eight feet of clearance behind it. Do not
place the treadmill on any surface that blocks
air openings. To protect the floor or carpet
from damage, place a mat under the tread­mill.

4. Keep the treadmill indoors, away from mois­ture and dust. Do not put the treadmill in a
garage or covered patio, or near water.

5. Do not operate the treadmill where aerosol
products are used or where oxygen is being
administered.

6. Keep children under the age of 12 and pets
away from the treadmill at all times.

7. The treadmill should not be used by persons
weighing more than 250 pounds.

8. Never allow more than one person on the
treadmill at a time.

9. Wear appropriate exercise clothing when
using the treadmill. Do not wear loose cloth­ing that could become caught in the tread­mill. Athletic support clothes are recommend­ed for both men and women. Always wear

athletic shoes. Never use the treadmill with
bare feet, wearing only stockings, or in san­dals.

10. When connecting the power cord (see page 7),
plug the power cord into a surge suppressor
(not included) and plug the surge suppressor
into a grounded circuit capable of carrying 15
or more amps. No other appliance should be
on the same circuit. Do not use an extension
cord.

11. Use only a single-outlet surge suppressor that
is UL 1449 listed as a transient voltage surge
suppressor (TVSS). The surge suppressor
must have a UL suppressed voltage rating of
400 volts or less and a minimum surge dissi­pation of 450 joules. The surge suppressor
must be electrically rated for 120 volts AC and
15 amps. To purchase a surge suppressor,
see your local WESLO dealer or call 1-800­999-3756 and order part number 146148.

12. Keep the power cord and the surge suppres­sor away from heated surfaces.

IMPORTANT PRECAUTIONS

WARNING:

To reduce the risk of burns, fire, electric shock, or injury to persons, read

the following important precautions and information before operating the treadmill.

3

13. Never move the walking belt while the power
is turned off. Do not operate the treadmill if
the power cord or plug is damaged, or if the
treadmill is not working properly. (See
BEFORE YOU BEGIN on page 4 if the tread­mill is not working properly.)

14. Never start the treadmill while you are stand­ing on the walking belt. Always hold the
handrails while using the treadmill.

15. Using hand weights and not holding the
handrails may compromise your ability to
maintain your balance. Hand weights should
be used only by experienced users.

16. The treadmill is capable of high speeds.
Adjust the speed in small increments to
avoid sudden jumps in speed.

17. Never leave the treadmill unattended while it
is running. Always remove the key and unplug
the power cord when the treadmill is not in
use.

18. Do not attempt to raise, lower, or move the
treadmill until it is properly assembled. (See
ASSEMBLY on page 5, and HOW TO FOLD
AND MOVE THE TREADMILL on page 10.) You
must be able to safely lift 45 pounds (20 kg) in
order to raise, lower, or move the treadmill.

19. Do not change the incline of the treadmill by
placing objects under the treadmill.

20. When folding or moving the treadmill, make

sure that the storage latch is fully closed.

21. Inspect and tighten all parts of the treadmill
every three months.

22. Never insert or drop any object into any
opening.

22. The roller guards must be 1/8 inch from the
rear roller (see the drawing on page 4).
Remove the key and adjust the roller guards,
if necessary.

22. DANGER: Always unplug the power

cord immediately after use, before cleaning
the treadmill, and before performing the
maintenance and adjustment procedures
described in this manual. Never remove the
motor hood unless instructed to do so by an
authorized service representative. Servicing
other than the procedures in this manual
should be performed by an authorized ser­vice representative only.

24. This treadmill is intended for in-home use
only. Do not use this treadmill in any com­mercial, rental, or institutional setting.

WARNING: Before beginning this or any exercise program, consult your physician.

This is especially important for persons over the age of 35 or persons with pre-existing health prob­lems. Read all instructions before using. ICON assumes no responsibility for personal injury or prop­erty damage sustained by or through the use of this product.

SAVE THESE INSTRUCTIONS

The decal shown below has been placed on your treadmill. If
the decal is missing or illegible, please call our Customer
Service Department, toll-free, to order a free replacement
decal (see ORDERING REPLACEMENT PARTS on the back
cover of this manual). Apply the decal in the location shown.

Note: This decal is shown at 38% of actual size.

4

BEFORE YOU BEGIN

Thank you for selecting the WESLO¨CADENCE ex14
treadmill. The CADENCE ex14 combines advanced
technology with innovative design to let you enjoy an
excellent form of cardiovascular exercise in the conve­nience and privacy of your home. And when youÕre not
exercising, the CADENCE ex14 can be folded up, re­quiring less than half the floor space of other treadmills.

For your benefit, read this manual carefully before
using the treadmill. If you have additional questions,

please call our Customer Service Department toll-free

at 1-800-999-3756, Monday through Friday, 6 a.m.
until 6 p.m. Mountain Time (excluding holidays). To
help us assist you, please note the product model
number and serial number before calling. The model
number of the treadmill is WLTL29200. The serial
number can be found on a decal attached to the tread­mill (see the front cover of this manual for the location).

Before reading further, please familiarize yourself with
the parts that are labeled in the drawing below.

Handrails

Console

Storage Latch

Speed Control

Key/Clip

Circuit Breaker

Walking Belt

Foot Rails

Roller Guards

Incline Leg

Incline Pin

Power Cord

FRONT

BACK

RIGHT SIDE

Rear Roller
Adjustment Bolts

Water Bottle Holder

(Bottle not included)

Accessory Tray

Uprights

ASSEMBLY

Assembly requires two people. Set the treadmill in a cleared area and remove all packing materials. Do not
dispose of the packing materials until assembly is completed. Assembly requires the included allen wrench
and your own phillips screwdriver and two adjustable wrenches .

Note: The underside of the treadmill walking belt is coated with high-performance lubricant. During shipping, a
small amount of lubricant may be transferred to the top of the walking belt or the shipping carton. This is a nor­mal condition and does not affect treadmill performance. If there is lubricant on top of the walking belt, simply
wipe off the lubricant with a soft cloth and a mild, non-abrasive cleaner.

1. Note that the Right Handrail and the Console Base
(not shown) are connected to the treadmill by a Wire
Harness. During assembly steps 1Ð3, be careful

not to pull on or damage the Wire Harness.

With the help of a second person, carefully lay the
treadmill on its side. Position one of the Base Legs
(62) on the base of the Upright (46) as shown. Make
sure that the Base Leg Pads (63) and the Wheel (68)
are in the indicated positions. Attach the Base Leg
with two silver Base Leg Bolts (65), two silver Base
Leg Washers (66), and two Base Leg Nuts (61).

Carefully turn the treadmill onto its other side.
Assemble the other Base Leg (62) as described.

With the help of a second person, carefully raise the
treadmill to the upright position so that both Base
Legs (62) are resting flat on the floor.

5

65

66

63

62

68

46

61

Screw (2)Ð2

Handrail Washer
(43) (Black)Ð4

Base Leg Washer

(66) (Silver)Ð4

Console Screw (11)Ð4

Weight Rack Screw (40)Ð12

Upright Bolt (42) (Black)Ð4

Base Leg Nut (61) (Silver)Ð4

Handrail Star Washer (44)Ð4

Base Leg Bolt (65) (Silver)Ð4

1

6

2. Refer to HOW TO LOWER THE TREADMILL FOR USE

on page 11. Follow step 2 on page 11 to lower the tread­mill.

Hold a Handrail (30) against the left Upright (46) as
shown. Thread two black Handrail Bolts (42), with two
black Handrail Washers (43) and two Handrail Star
Washers (44), into the left Upright and the Left Handrail.

Do not tighten the Handrail Bolts yet.

Have a second person hold the Console Base (52) and
the right Handrail (30) near the right Upright (46) as
shown. Feed the excess Wire Harness (60) into the
upper end of the right Handrail and Upright.

Attach the right Handrail (30) to the right Upright (46)
with two black Handrail Bolts (42), two black Handrail
Washers (43), and two Handrail Star Washers (44). Do

not tighten the Handrail Bolts yet. Be careful not to
pinch the Wire Harness (60).

3. Attach the Console Base (52) to the Handrails (30) with

four Handrail Screws (11).

Feed the excess Wire Harness (60) into the upper end of
the right Handrail (30).

Tighten all parts used in steps 2 and 3.

4. Attach the Storage Latch (48) to the Upright (46) with
two Screws (2). Be careful not to overtighten the

Screws.

5. Attach a Weight Rack (41) to the side of the right Upright
(46) with six Weight Rack Screws (40).

Set a 3-lb. Weight (not shown) on the bottom hanger, a
2-lb. Weight on the middle hanger, and a 1-lb. Weight on
the top hanger.

Attach the other Weight Rack and Weights to the left
Upright as described above (not shown).

6. Make sure that all parts are tightened before you use
the treadmill. To protect the floor or carpet, place a mat
under the treadmill.

30

11

11

30

60

3

52

2

46

48

46

41

40

40

Hanger

40

2

44

43

46

52

60

60

30

30

46

43

42

44

42

5

4

7

OPERATION AND ADJUSTMENT

THE PERFORMANT LUBETMWALKING BELT

Your treadmill features a walking belt coated with
PERFORMANT LUBETM, a high-performance lubricant.

IMPORTANT: Never apply silicone spray or other
substances to the walking belt or the walking plat­form. Such substances will deteriorate the walking
belt and cause excessive wear.

HOW TO PLUG IN THE POWER CORD

Your treadmill, like any other type of sophisticated
electronic equipment, can be seriously damaged by
sudden voltage changes in your homeÕs power.
Voltage surges, spikes, and noise interference can
result from weather conditions or from other appliances
being turned on or off. To decrease the possibility of

your treadmill being damaged, always use a surge
suppressor with your treadmill (see drawing 1 at
the right).

To purchase a surge suppressor, see your local
WESLO dealer or call toll-free 1-800-999-3756 and
order part number 146148. Use only a single-outlet

surge suppressor that is UL 1449 listed as a transient
voltage surge suppressor (TVSS). The surge suppres­sor must have a UL suppressed voltage rating of 400
volts or less and a minimum surge dissipation of 450
joules. The surge suppressor must be electrically
rated for 120 volts AC and 15 amps.

This product must be grounded. If it should mal­function or break down, grounding provides a path of
least resistance for electric current to reduce the risk
of electric shock. This product is equipped with a cord
having an equipment-grounding conductor and a
grounding plug. Plug the power cord into a surge

suppressor, and plug the surge suppressor into an
appropriate outlet that is properly installed and
grounded in accordance with all local codes and
ordinances. Important: The treadmill is not com­patible with GFCI-equipped outlets.

This product is for use on a nominal 120-volt circuit,
and has a grounding plug that looks like the plug illus­trated in drawing 1 below. A temporary adapter that
looks like the adapter illustrated in drawing 2 may be
used to connect the surge suppressor to a 2-pole
receptacle as shown in drawing 2 if a properly
grounded outlet is not available.

The temporary adapter should be used only until a
properly grounded outlet (drawing 1) can be installed
by a qualified electrician.

The green-colored rigid ear, lug, or the like extending
from the adapter must be connected to a permanent
ground such as a properly grounded outlet box cover.
Whenever the adapter is used it must be held in place
by a metal screw. Some 2-pole receptacle outlet

box covers are not grounded. Contact a qualified
electrician to determine if the outlet box cover is
grounded before using an adapter.

DANGER: Improper connection

of the equipment-grounding conductor can
result in an increased risk of electric shock.
Check with a qualified electrician or service­man if you are in doubt as to whether the
product is properly grounded. Do not modify
the plug provided with the productÑif it will
not fit the outlet, have a proper outlet
installed by a qualified electrician.

1

2

Grounded Outlet Box

Grounded Outlet Box

Grounding Plug

Surge Suppressor

Surge Suppressor

Grounding Pin

Adapter

Lug

Metal Screw

Grounded Outlet

Grounding Pin

8

DIAGRAM OF THE CONSOLE

Clip

Key

Speed Control

Monitor Display

the negative (Ð) ends of the batteries touching the
springs. Close the battery cover, push up on the tab,
and then push the tab forward as shown. Be sure that
the tab locks into place.

STEP-BY-STEP CONSOLE OPERATION

Before operating the console, make sure that the
power cord is properly plugged in. (See HOW TO
PLUG IN THE POWER CORD on page 7.) If there is
a thin sheet of clear plastic on the console, remove it.

Stand on the foot rails of the treadmill. Find the clip
attached to the key, and slide the clip onto the waist­band of your clothing. Next, insert the key into the
console. Test the clip by carefully taking a few

steps backward until the key is pulled from the
console. If the key is not pulled from the console,
adjust the position of the clip as needed.

Follow the steps on page 9 to operate the console.

BATTERY INSTALLATION

The console requires two "AA" batteries (not includ­ed). Alkaline batteries are recommended. To install
batteries, open the battery cover as shown at the right.
Press two batteries into the battery compartment, with

CAUTION: Before operating the

console, read the following precautions.

¥ Do not stand on the walking belt when turn-

ing on the power.

¥ Always wear the clip (see the drawing

above) while operating the treadmill. When
the key is removed from the console, the
walking belt will stop.

¥ Adjust the speed in small increments.

¥ The training zones marked around the speed

control are general guidelines only. See
page 14 or more information.

¥ To reduce the possibility of electric shock,

keep the console dry. Avoid spilling liquids
on the console and use only a sealable
water bottle.

Batteries

Battery Cover

Battery

Cover Tab

9

Insert the key fully into the power switch.

Inserting the key will
not turn on the dis­play. The display will
turn on when the
ON/RESET button is
pressed or when the
walking belt is start­ed. Note: If you just
installed batteries, the display will already be on.

Reset the speed control and start the walking
belt.

Turn the speed
control to the RESET
position. Note: Each

time the walking
belt is stopped, the
speed control must
be turned to the
RESET position
before the walking belt can be restarted.

Next, slowly turn the speed control until the walk­ing belt begins to move at slow speed. Carefully
step onto the walking belt and begin exercising.
Change the speed of the walking belt as desired
by turning the speed control.

To stop the walking belt, step onto the foot rails
and turn the speed control to the RESET position.

Follow your progress with the monitor modes

When the power is
turned on, the con­sole will scan through
five modes repeatedly.
A flashing mode indi­cator will show which
mode is currently dis­played. The modes are described below.

¥ SpeedÑThis mode shows your speed, in miles

per hour.

¥ TimeÑThis mode shows the elapsed time. Note:

If you stop exercising for ten seconds or longer,
the time mode will pause.

¥ DistanceÑThis mode shows the total number of

miles you have walked or run.

¥ Fat Calories (F CALS)ÑThis mode shows the

approximate number of fat calories you have
burned. (See FAT BURNING on page 14.)

¥ Calories (CALS)ÑThis mode shows the approxi-

mate number of calories you have burned.

If desired, the display can be reset by pressing
the DISPLAY button.

When you are finished exercising, stop the
walking belt and remove the key.

Step onto the foot rails, stop the walking belt, and
remove the key from the console. The display will
turn off about six minutes after the key is removed.

Note: The display will automatically turn off in
order to conserve the batteries any time that
the walking belt is stopped and the ON/RESET
button is not pressed for six minutes.

HOW TO CHANGE THE INCLINE OF THE TREADMILL

To vary the intensity of your exercise, the incline of the
treadmill can be changed. There are three different
incline levels. Before changing the incline, remove
the key and unplug the power cord. Next, fold the
treadmill to the storage position (see HOW TO FOLD
THE TREADMILL FOR STORAGE on page 10).

To change the incline, first remove the incline pin from
the right incline leg as shown below. Adjust the incline
leg to the desired height and fully reinsert the incline
pin. Make sure that the incline pin is in the ÒlockedÓ
position shown in the inset drawing.

Adjust the left incline leg in the same manner. Make

sure that both incline pins are inserted from the
direction shown.

CAUTION: Before using the treadmill, make sure
that both incline pins are fully inserted at the same
height. Do not use the treadmill with the incline
pins removed. After you have adjusted the incline

legs, lower the treadmill (see HOW TO LOWER THE
TREADMILL FOR USE on page 11).

4

3

2

1

Incline

Pin

Incline

Pin

Incline Pin

Right

Incline

Leg

Mode Indicator

HOW TO FOLD AND MOVE THE TREADMILL

HOW TO FOLD THE TREADMILL FOR STORAGE

Before folding the treadmill, unplug the power cord.

Caution: You must be able to safely lift 45 pounds (20
kg) in order to raise, lower or move the treadmill.

1. Hold the treadmill with your hands in the locations shown

at the right. To decrease the possibility of injury, bend

your legs and keep your back straight. As you raise
the treadmill, make sure to lift with your legs rather
than your back. Raise the treadmill about halfway to the

vertical position.

2. Move your right hand to the position shown and hold the

treadmill firmly. Using your left thumb, press the storage
latch and hold it. Pivot the treadmill until the frame and
foot rail are past the storage latch. Close the storage
latch over the catch. Make sure that the storage latch

is fully engaged over the catch.

To protect the floor or carpet from damage, place a
mat under the treadmill. Keep the treadmill out of
direct sunlight. Do not leave the treadmill in the stor­age position in temperatures above 85¡ Fahrenheit.

HOW TO MOVE THE TREADMILL

Before moving the treadmill, convert the treadmill to the
storage position as described above. Make sure that the

storage latch is locked fully over the catch.

1. Remove the weights from the weight racks.

2. Hold the upper ends of the handrails. Place one foot on

one of the wheel as shown.

3. Tilt the treadmill back until it rolls freely on the wheels.

Carefully move the treadmill to the desired location. To

reduce the risk of injury, use extreme caution while
moving the treadmill. Do not attempt to move the
treadmill over an uneven surface.

4. Place one foot on the base, and carefully lower the tread-

mill until it is resting in the storage position.

10

Base

Leg

Wheels

Storage

Latch

Catch

Closed

11

HOW TO LOWER THE TREADMILL FOR USE

1. Hold the upper end of the treadmill with your right hand

as shown. Using your left thumb, press the storage latch
and hold it. Pivot the treadmill until the frame and foot
rail are past the storage latch.

2. Hold the treadmill firmly with both hands, and lower the

treadmill to the floor. Do not drop the treadmill frame

to the floor. To decrease the possibility of injury,
bend your legs and keep your back straight.

Storage

Latch

Catch

Opened

12

MAINTENANCE AND TROUBLE-SHOOTING

Most treadmill problems can be solved by following the steps below. Find the symptom that applies, and
follow the steps listed. If further assistance is needed, please call our Customer Service Department toll­free at 1-800-999-3756, Monday through Friday, 6 a.m. until 6 p.m. Mountain Time (excluding holidays).

PROBLEM: The power does not turn on

SOLUTION: a. Make sure that the power cord is plugged into a surge suppressor, and that the surge suppres-

sor is plugged into a properly grounded outlet (see page 7). Use only a single-outlet surge sup­pressor that is UL 1449 listed as a transient voltage surge suppressor (TVSS). The surge sup­pressor must have a UL suppressed voltage rating of 400 volts or less and a minimum surge dis­sipation of 450 joules. The surge suppressor must be electrically rated for 120 volts AC and 15
amps. Important: The treadmill is not compatible with GFCI-equipped outlets.

b. After the power cord has been plugged in, make sure that the key is fully inserted into the console.

c. Check the circuit breaker located on the treadmill

frame near the power cord. If the switch protrudes
as shown, the circuit breaker has tripped. To reset
the circuit breaker, wait for five minutes and then
press the switch back in.

PROBLEM: The power turns off during use

SOLUTION: a. Check the circuit breaker located on the treadmill frame near the power cord (see the drawing

above). If the circuit breaker has tripped, wait for five minutes and then press the switch back in.

b. Make sure that the power cord is plugged in.

c. Remove the key from the console. Reinsert the key fully into the console.

d. If the treadmill still will not run, please call our Customer Service Department, toll-free.

PROBLEM: The displays of the console do not function properly

SOLUTION: a. Check the batteries in the console. If the batteries need to be replaced, see ÒBATTERY

INSTALLATIONÓ on page 8. Most problems are the result of drained batteries.

b. Remove the screws from the hood, and carefully

remove the hood. Locate the Reed Switch (76) and
the Magnet (93) on the left side of the Pulley (77).
Turn the Pulley until the Magnet is aligned with the
Reed Switch. Make sure that there is a gap of

about 1/8Ó between the Magnet and the Reed
Switch. If necessary, loosen the Screw (17) and

move the Reed Switch slightly. Retighten the Screw.
Re-attach the hood, and run the treadmill for a few
minutes to check for a correct speed reading.

Tripped

Tripped

Reset

c

93

76

17

Top

View

1/8Ó

77

b

Reset

13

PROBLEM: The walking belt is off-center or slips when walked on

SOLUTION: a. If the walking belt has shifted to the left, first

remove the key and UNPLUG THE POWER CORD.
Using the allen wrench, turn the left rear roller
adjustment bolt clockwise, and the right bolt counter­clockwise, 1/4 of a turn each. Be careful not to over­tighten the walking belt. Plug in the power cord,
insert the key and run the treadmill for a few min­utes. Repeat until the walking belt is centered.

b. If the walking belt has shifted to the right, first

remove the key and UNPLUG THE POWER CORD.
Using the allen wrench, turn the left rear roller
adjustment bolt counterclockwise, and the right bolt
clockwise, 1/4 of a turn each. Be careful not to over­tighten the walking belt. Plug in the power cord,
insert the key and run the treadmill for a few min­utes. Repeat until the walking belt is centered.

c. If the walking belt slips when walked on, first

remove the key and UNPLUG THE POWER CORD.
Using the allen wrench, turn both rear roller adjust­ment bolts clockwise, 1/4 of a turn. When the walk­ing belt is correctly tightened, you should be able to
lift each side of the walking belt 2 to 3 inches off the
walking platform. Be careful to keep the walking belt
centered. Plug in the power cord, insert the key and
run the treadmill for a few minutes. Repeat until the
walking belt is properly tightened.

PROBLEM: The walking belt slows when walked on

SOLUTION: a. Use only a UL-listed surge protector, rated at 15 amps, with a 14-gauge cord of five feet or less

in length.

b. If the walking belt is overtightened, treadmill perfor-

mance may decrease and the walking belt may be
permanently damaged. Remove the key and
UNPLUG THE POWER CORD. Using the allen
wrench, turn both rear roller adjustment bolts coun­terclockwise, 1/4 of a turn. When the walking belt is
properly tightened, you should be able to lift each
side of the walking belt 2 to 3 inches off the walking
platform. Be careful to keep the walking belt cen­tered. Plug in the power cord, insert the key and run
the treadmill for a few minutes. Repeat until the
walking belt is properly tightened.

c. If the walking belt still slows when walked on, please call our Customer Service Department, toll-

free.

b

c

a

Rear Roller
Adjustment Bolts

2ÓÐ3Ó

b

14

CONDITIONING GUIDELINES

The following guidelines will help you to plan your
exercise program. RememberÑthese are general
guidelines only; for more detailed exercise information,
obtain a reputable book or consult your physician.

EXERCISE INTENSITY

Whether your goal is to burn fat or to strengthen your
cardiovascular system, the key to achieving the
desired results is to exercise with the proper intensity.
The proper intensity level can be found by using your
heart rate as a guide. The chart below shows recom­mended heart rates for fat burning and aerobic exercise.

To find the proper heart rate for you, first find your age
on the left side of the chart (ages are rounded off to
the nearest ten years). Next, find the three numbers to
the right of your age. The three numbers are your
Òtraining zone.Ó The lower two numbers are recom­mended heart rates for fat burning; the higher number
is the recommended heart rate for aerobic exercise.

Fat Burning

To burn fat effectively, you must exercise at a relatively
low intensity level for a sustained period of time.
During the first few minutes of exercise, your body
uses easily accessible carbohydrate calories for ener-

gy. Only after the first few minutes does your body
begin to use stored fat calories for energy. If your goal
is to burn fat, adjust the speed of the treadmill until
your heart rate is near one of the lower two numbers in
your training zone. It may also be helpful to set the

speed control on the console to FAT BURN to help you
maintain the proper intensity level. (See page 9.)

Aerobic Exercise

If your goal is to strengthen your cardiovascular sys­tem, your exercise must be Òaerobic.Ó Aerobic exercise
is activity that requires large amounts of oxygen for
prolonged periods of time. This increases the demand
on the heart to pump blood to the muscles, and on the
lungs to oxygenate the blood. For aerobic exercise,
adjust the speed of the treadmill until your heart rate is
near the higher number in your training zone. It may
also be helpful to set the speed control on the console
to AEROBIC to help you maintain the proper intensity
level. (See page 9.)

High Performance Athletic Conditioning

If your goal is high performance athletic conditioning,
set the speed control on the console to PERFOR­MANCE to help you maintain the proper intensity
level. (See page 9.) Note: During the first few weeks
of your exercise program, keep your heart rate near
the low end of your training zone.

HOW TO MEASURE YOUR HEART RATE

To measure your
heart rate, stop
exercising and place
two fingers on your
wrist as shown.
Take a six-second
heartbeat count, and
multiply the result by
ten to find your
heart rate. (A six-second count is used because your
heart rate drops quickly when you stop exercising.) If
your heart rate is too high or too low, adjust the speed
or incline of the treadmill accordingly.

USING THE HAND WEIGHTS

The included hand weights let you add upper body
exercise to your workouts. As you walk on the tread­mill, hold the 1-lb. weights at your sides or press the
weights above your head. To increase the intensity of
your exercise, use the 2-lb. or 3-lb. weights.

WARNING: Do not use the hand weights at speeds
faster than a walk. Using weights and not holding
the handrails may compromise your ability to
maintain your balance. Exercises using weights
should be attempted only by experienced users.

WARNING: Before beginning

this or any exercise program, consult your
physician. This is especially important for
individuals over the age of 35 or individuals
with pre-existing health problems.

15

SUGGESTED STRETCHES

The correct form for several basic stretches is shown in the drawings
below. Move slowly as you stretchÑnever bounce.

1. Toe Touch Stretch

Stand with your knees bent slightly and slowly bend forward from your
hips. Allow your back and shoulders to relax as you reach down toward
your toes as far as possible. Hold for 15 counts, then relax. Repeat 3
times. Stretches: Hamstrings, back of knees and back.

2. Hamstring Stretch

Sit with one leg extended. Bring the sole of the opposite foot toward you
and rest it against the inner thigh of your extended leg. Reach toward
your toes as far as possible. Hold for 15 counts, then relax. Repeat 3
times for both legs. Stretches: Hamstrings, lower back and groin.

3. Calf/Achilles Stretch

With one leg in front of the other, reach forward and place your hands
against a wall. Keep your back leg straight and your back foot flat on
the floor. Bend your front leg, lean forward and move your hips toward
the wall. Hold for 15 counts, then relax. Repeat 3 times for both legs. To
cause further stretching of the achilles tendons, bend your back leg as
well. Stretches: Calves, achilles tendons and ankles.

4. Quadriceps Stretch

With one hand against a wall for balance, reach back and grasp one
foot with your other hand. Bring your heel as close to your buttocks as
possible. Hold for 15 counts, then relax. Repeat 3 times for both legs.
Stretches: Quadriceps and hip muscles.

5. Inner Thigh Stretch

Sit with the soles of your feet together and your knees outward. Pull
your feet toward your groin area as far as possible. Hold for 15 counts,
then relax. Repeat 3 times. Stretches: Quadriceps and hip muscles.

1

2

3

4

5

WORKOUT GUIDELINES

Each workout should include the following three parts:

A Warm-up

Start each workout with 5 to 10 minutes of stretching
and light exercise. A proper warm-up increases your
body temperature, heart rate, and circulation in prepa­ration for exercise.

Training Zone Exercise

After warming up, increase the intensity of your exer­cise until your pulse is in your training zone for 20 to
60 minutes. (During the first few weeks of your exer­cise program, do not keep your pulse in your training

zone for longer than 20 minutes.) Breathe regularly
and deeply as you exerciseÑnever hold your breath.

A Cool-down

Finish each workout with 5 to 10 minutes of stretching
to cool down. This will increase the flexibility of your
muscles and will help prevent post-exercise problems.

Exercise Frequency

To maintain or improve your condition, complete three
workouts each week, with at least one day of rest
between workouts. After a few months, you may com­plete up to five workouts each week if desired. The

key to success is to make exercise a regular and
enjoyable part of your everyday life.

PART LISTÑModel No. WLTL29200 R1100A

Specifications are subject to change without notice. See the back cover of the userÕs manual for information
about ordering replacement parts.

Key No. Qty. Description Key No. Qty. Description

1 1 Motor Hood
2 16 Screw
3 20 3/4Ó Screw
4 5 8Ó Cable Tie
5 1 Cable Tie
6 1 Clamp Screw
7 1 Cable Tie Clamp
8 2 Foot Rail

9 8 Platform Isolator
10 8 Platform Screw
11 4 Console Screw
12 2 Incline Leg Washer
13 1 Catch
14 2 Belt Guide
15 4 Belt Guide Screw
16 1 Reed Switch Clip
17 1 Reed Switch Screw
18 4 Hood Anchor
19 1 Motor
20 1 Pulley/Flywheel/Fan

21* 1 Motor/Pulley/Flywheel/Fan
22 1 Motor Tension Bolt
23 1 Motor Tension Washer
24 1 Motor Star Washer
25 2 Motor Tension Nut
26 1 Motor Pivot Bolt
27 2 Frame Spacer
28 1 Power Cord Grommet
29 3 Wire Clip
30 1 Power Cord
31 1 Controller
32 8 Electronic Screw
33 1 Choke
34 2 Bracket Screw
35 1 Electronics Bracket
36 1 Circuit Breaker
37 2 Base Leg Endcap
38 2 Roller Adjustment Washer
39 1 Front Roller Adjustment Bolt
40 12 Weight Rack Screw
41 2 Weight Rack
42 4 Handrail Bolt
43 4 Handrail Washer
44 4 Handrail Star Washer
45 2 Handrail
46 1 Upright Base
47 1 Magnet
48 1 Storage Latch

49 1 Left Endcap
50 1 Ground Wire
51 1 Key/Clip
52 1 Console Base
53 1 Console Plug
54 1 Battery Cover
55* 1 Console Assembly
56 1 Speed Potentiometer
57 1 Console
58 1 Upright Grommet
59 2 Upright Endcap
60 1 Wire Harness
61 8 Base Leg Nut
62 2 Base Leg
63 4 Base Leg Pad
64 2 Handrail Endcap
65 4 Base Leg
66 6 Wheel Washer/Base Leg Washer
67 2 Wheel Bolt
68 2 Wheel
69 1 Speed Control
70 2 Frame Pivot Bolt
71 2 Frame Pivot Washer
72 1 Walking Belt
73 1 Belly pan
74 1 Walking Board
75 1 Warning Decal
76 1 Reed Switch/Sensor Wire
77 1 Drive Roller/Pulley
78 1 Frame Guide
79 1 Frame
80 2 Incline Pin
81 2 Incline Leg
82 2 Incline Leg Cap
83 1 Right Endcap
84 2 Roller Guard
85 1 Rear Roller
86 2 Rear Roller Adjustment Bolt
87 1 Allen Wrench
88 2 1-lb. Weight
89 2 2-lb. Weight
90 1 Motor Belt
91 2 3-lb. Weight
92 2 Hole Plug

# 1 8Ó White Wire, Male/Female

# 1 UserÕs Manual
* Includes all parts shown in the box
Note: Ò#Ó indicates a non-illustrated part.

89

91

5

6

7

4

2

2

2

2

22

23

24

25

32

32

32

31

26

34

35

20

19

25

76

27

17

61

93

16

3

9

10

47

3

18

33

51

30

28

36

29

3

18

39

38

41

40

40

40

27

3

8

10

3

3

45

43

42

44

70

71

61

2

53

52

54

11

2

2

11

57

69

56

55*

2

40

48

46

41

58

43

42

44

61

61

60

32

61

40

40

61

68

67

63

3

63

66

3

65

62

63

62

3

66

65

3

63

67

68

61

79

14

73

3

77

74

72

10

10

10

78

15

2

80

82

81

84

9

3

9

9

9

38

83

86

82

81

85

49

38

86

87

9

10

3

84

9

2

13

10

80

14

15

10

9

8

1

45

21*

75

71

70

60

32

50

3

3

88

12

12

90

66

66

59

59

37

37

92

92

64

64

EXPLODED DRAWINGÑModel No. WLTL29200 R1100A

Part No. 165301 R1100A Printed in USA © 2000 ICON Health & Fitness, Inc.

ORDERING REPLACEMENT PARTS

To order replacement parts, simply call our Customer Service Department toll-free at 1-800-999-3756, Monday
through Friday, 6 a.m. until 6 p.m. Mountain Time (excluding holidays). To help us assist you, please be pre­pared to give the following information when calling:

¥ The MODEL NUMBER of the product (WLTL29200).

¥ The NAME of the product (WESLO CADENCE¨ex14 treadmill).

¥ The SERIAL NUMBER of the product (see the front cover of this manual).

¥ The KEY NUMBER and DESCRIPTION of the desired part(s) (see the PART LIST and the EXPLODED

DRAWING in the center of this manual).

WESLO is a registered trademark of ICON Health & Fitness, Inc.

LIMITED WARRANTY

ICON Health & Fitness, Inc. (ICON), warrants this product to be free from defects in workmanship and
material, under normal use and service conditions, for a period of ninety (90) days from the date of pur­chase. This warranty extends only to the original purchaser. ICON's obligation under this warranty is lim­ited to replacing or repairing, at ICON's option, the product through one of its authorized service centers.
All repairs for which warranty claims are made must be pre-authorized by ICON. This warranty does not
extend to any product or damage to a product caused by or attributable to freight damage, abuse, misuse,
improper or abnormal usage or repairs not provided by an ICON authorized service center, products used
for commercial or rental purposes, or products used as store display models. No other warranty beyond
that specifically set forth above is authorized by ICON.

ICON is not responsible or liable for indirect, special or consequential damages arising out of or in con­nection with the use or performance of the product or damages with respect to any economic loss, loss of
property, loss of revenues or profits, loss of enjoyment or use, costs of removal, installation or other con­sequential damages of whatsoever nature. Some states do not allow the exclusion or limitation of inci­dental or consequential damages. Accordingly, the above limitation may not apply to you.

The warranty extended hereunder is in lieu of any and all other warranties and any implied warranties of
merchantability or fitness for a particular purpose is limited in its scope and duration to the terms set forth
herein. Some states do not allow limitations on how long an implied warranty lasts. Accordingly, the above
limitation may not apply to you.

This warranty gives you specific legal rights. You may also have other rights which vary from state to state.

ICON HEALTH & FITNESS, INC., 1500 S. 1000 W., LOGAN, UT 84321-9813