OPERATOR’S MANUAL
Oscillating Multi Tool Kit
Item # 2310
IMPORTANT:
You new WEN® tool/equipment has been engineered and
manufactured to high standards for dependability, ease of
operation, and operator safety. Properly cared for, it will give
you years of rugged, trouble-free performance.
It’s not how, it’s WEN the project get’s done.
Contact us for product questions or technical support.
Wenproducts.com
800-232-1195 M-F 8-5 (CST)
techsupport@wenproducts.com
2
CONTENTS
Specifications…..……………………………………………………….. 3
General safety rules…….……………………………………………….. 4
Specific safety rules warnings…………………………………………... 6
Vibration Safety………………………………………………………… 7
Electrical information…………………………………………………... 8
Assembly………………………………………………………………… 9
Operation………………………………………………………………... 10
Maintenance…………………………………………………………….. 11
Troubleshooting………………………………………………………… 12
Exploded view…………………………………………………………… 13
Parts list…………………………………………………………………... 14
Warranty statement………………………………………………………. 15
SPECIFICATIONS
Oscillating Multi Tool Kit
Item #: 2310
Motor: 120V AC, 60 Hz
Current Rating : 1.6 AMP
Oscillating Speed: 21,000 OPM
Oscillation Angle: 1.5° (Left/Right)
Weight: 1.9 lbs
3
GENERAL SAFETY RULES
WARNING: Read all safety warnings and instructions. Failure to follow the
warnings and instructions may result in electric shock, fire and/or serious
injury. Save all warnings and instructions for future reference.
1. Work area safety
a. Keep work area clean and well lit. Cluttered or dark areas invite accidents.
b. Do not operate power tools in explosive atmospheres, such as in the presence of
flammable liquids, gases or dust. Power tools create sparks which may ignite the
dust or fumes.
c. Keep children and bystanders away while operating a power tool. Distractions can
cause you to lose control.
2. Electrical safety
a. Power tool Plugs must match the outlet. Never modify the Plug in any way. Do
not use any adapter plugs with grounded power tools. Unmodified plugs and
matching outlets will reduce risk of electric shock.
b. Avoid body contact with grounded surfaces such as pipes, radiators, ranges and
refrigerators. There is an increased risk of electric shock if your body is grounded.
c. Do not expose power tools to rain or wet conditions. Water entering a power tool
will increase the risk of electric shock.
d. Do not abuse the Power Cord. Never use the Cord for carrying, pulling or
unplugging the power tool. Keep Cord away from heat, oil, sharp edges or
moving parts. Damaged or entangled cords increase the risk of electric shock.
e. When operating a power tool outdoors, use an extension cord suitable for outdoor
use. Use of a cord suitable for outdoor use reduces the risk of electric shock.
f. If operating a power tool in a damp location is unavoidable, use a Ground Fault
Circuit Interrupter (GFCI) protected supply. Use of a GFCI reduces the risk of
electric shock.
3. Personal safety
a. Stay alert, watch what you are doing and use common sense when operating a
power tool. Do not use a power tool while you are tired or under the influence of
drugs, alcohol or medication. A moment of inattention while operating power
tools may result in serious personal injury.
b. Use personal protective equipment. Always wear ANSI-approved safety goggles.
Safety equipment such as NIOSH-approved dust mask/respirator, NIOSHapproved hearing protection, and heavy duty work gloves will reduce personal
injuries.
c. Prevent unintentional starting. Ensure the Power Switch is in the off-position
before connecting to the power source or picking up or carrying the tool. Carrying
power tools with your finger on the Power Switch invites accidents.
d. Remove any adjusting key or wrench before turning the power tool on. A wrench
or a key left attached to an oscillating part of the power tool may result in
personal injury.
4
e. Do not overreach. Keep proper footing and balance at all times. This enables
better control of the power tool in unexpected situations.
f. Dress properly. Do not wear loose clothing or jewelry. Keep your hair, clothing
and gloves away from moving parts. Loose clothes, jewelry or long hair can be
caught in moving parts.
4. Power tool use and care
a. Do not force the power tool. Use the correct power tool for your application. The
correct power tool will do the job better and safer at the rate for which it was
designed.
b. Do not use the power tool if the Power Switch does not turn it on and off. Any
power tool that cannot be controlled with the Switch is dangerous and must be
repaired.
c. Disconnect the Power Cord from the power source before making any
adjustments, changing accessories, or storing the power tool. Such preventive
safety measures reduce the risk of starting the power tool accidentally.
d. Store idle power tools out of the reach of children and do not allow persons
unfamiliar with the power tool or these instructions to operate the power tool.
Power tools are dangerous in the hands of untrained users.
e. Maintain power tools. Check for misalignment or binding of moving parts,
breakage of parts and any other condition that may affect the power tool’s
operation. If damaged, have the power tool repaired before use. Many accidents
are caused by poorly maintained power tools.
f. Keep cutting accessories sharp and clean. Properly maintained cutting accessories
with sharp cutting edges are less likely to bind and are easier to control.
g. Use the power tool and its accessories in accordance with these instructions,
taking into account the working conditions and the work to be performed. Use of
the power tool for operations different from those intended could result in a
hazardous situation.
5. Service
Have your power tool serviced by a qualified repair person using only identical
replacement parts. This will ensure that the safety of the power tool is maintained.
5
SPECIFIC SAFETY WARNINGS
1. Maintain labels and nameplates on the power tool. These carry important safety
information. If unreadable or missing, contact Harbor Freight Tools for a
replacement.
2. CAUTION: Avoid accidental injury. Keep hands and fingers safely away from
the oscillating Angled Scraper (4), Blades (501, 503), and Sanding Pad (502)
when operating the Tool.
3. Avoid unintentional starting. Prepare to begin work before turning on the power
tool.
4. Do not lay the power tool down until it has come to a complete stop. Moving
parts can grab the surface and pull the tool out of your control.
5. When using a handheld power tool, maintain a firm grip on the tool with both
hands to resist starting torque.
6. Do not leave the power tool unattended when it is plugged into an electrical outlet.
Turn off the tool, and unplug it from its electrical outlet before leaving.
7. This product is not a toy. Keep it out of reach of children.
8. People with pacemakers should consult their physician(s) before use.
Electromagnetic fields in close proximity to heart pacemaker could cause
pacemaker interference or pacemaker failure. In addition, people with pacemakers
should:
a. Avoid operating alone.
b. Do not use with power switch locked on.
c. Properly maintain and inspect to avoid electrical shock.
d. Any power cord must be properly grounded. Ground Fault Circuit Interrupter
(GFCI) should also be implemented – it prevents sustained electrical shock.
9. Some dust created by power sanding, sawing, grinding, drilling, and other
construction activities, contains chemicals known [to the State of California] to
cause cancer, birth defects or other reproductive harm. Some examples of these
chemicals are:
a. Lead from lead-based paints
b. Crystalline silica from bricks and cement or other masonry products
c. Arsenic and chromium from chemically treated lumber
Your risk from these exposures varies, depending on how often you do this type
of work. To reduce your exposure to these chemicals: work in a well ventilated
area, and work with approved safety equipment, such as those dust masks that are
specially designed to filter out microscopic particles. (California Health & Safety
Code § 25249.5, et seq.)
10. Handling the Power Cord on this product will expose you to lead, a chemical
known to the State of California to cause cancer, and birth defects or other
reproductive harm. Wash hands after handling. (California Health & Safety Code
§ 25249.5, et seq.)
11. The warnings, precautions, and instructions discussed in this instruction manual
cannot cover all possible conditions and situations that may occur. It must be
understood by the operator that common sense and caution are factors which
cannot be built into this product, but must be supplied by the operator.
6
VIBRATION SAFETY
This power tool vibrates during use. Repeated or long-term exposure to vibration may
cause temporary or permanent physical injury, particularly to the hands, arms and
shoulders. To reduce the risk of vibration-related injury:
1. Anyone using vibrating power tools regularly or for an extended period should first
be examined by a doctor and then have regular medical check-ups to ensure medical
problems are not being caused or worsened from use. Pregnant women or people who
have impaired blood circulation to the hand, past hand injuries, nervous system
disorders, diabetes, or Raynaud’s Disease should not use this tool. If you feel any
medical or physical symptoms related to vibration (such as tingling, numbness, and
white or blue fingers), seek medical advice as soon as possible.
2. Do not smoke during use. Nicotine reduces the blood supply to the hands and fingers,
increasing the risk of vibration-related injury.
3. Wear suitable gloves to reduce the vibration effects on the user.
4. Use power tools with the lowest vibration when there is a choice between different
processes.
5. Include vibration-free periods each day of work.
6. Grip the power tool as lightly as possible (while still keeping safe control of it). Let
the tool do the work.
7. To reduce vibration, maintain the power tool as explained in this manual. If any
abnormal vibration occurs, stop use immediately.
7
ELECTRICAL INFORMATION
Ampere Rating
Total Length of Cord in feet
More Than
Not More
Than
25
50
100
150
0 6 18
16
16
14 6 10
18
16
14
12
10
12
16
16
14
12
12
16
14
12
Not Recommended
WARNING: This drill press is for indoor use only. Do not expose to rain or
use in damp locations.
Guidelines for using extension cords
Make sure your extension cord is in good condition. When using an extension cord, be
sure to use one heavy enough to carry the current your product will draw. An undersized
cord will cause a drop in line voltage resulting in loss of power and overheating. The
table below shows the correct size to be used according to cord length and nameplate
ampere rating. If in doubt, use the next heavier gauge. The smaller the gauge number, the
heavier the cord.
Minimum Gauge for Extension Cords (AWG)
(When using 120 V only)
Make sure your extension cord is properly wired and in good condition. Always replace a
damaged extension cord or have it repaired by a qualified person before using it.
Protect your extension cords from sharp objects, excessive heat and damp or wet areas.
Use a separate electrical circuit for your tools. This circuit must not be less than a #12
wire and should be protected with a 15 A time-delayed fuse. Before connecting the motor
to the power line, make sure the switch is in the OFF position and the electric current is
rated the same as the current stamped on the motor nameplate. Running at a lower
voltage will damage the motor.
WARNING: This tool must be grounded while in use to protect the operator
from electric shock.
8
ASSEMBLY
Unpacking
When unpacking, check to make sure that the item is intact and undamaged. If any parts
are missing or broken, please call our customer service at 1-800-232-1195.
Assembly Instructions
Warning: To Prevent Serious Injury From Accidental Operation:
Turn the power switch of the tool to its “OFF” position and unplug the tool
from its electrical outlet before assembling or making any adjustments to the tool.
Note: For additional information regarding the parts listed in the following pages, refer to
the Exploded View and Parts List near the end of this manual.
Prior to attaching or removing any one of
the attachments, turn off the unit and
unplug the tool from its electrical source.
Place attachment over Spindle shoulder
and facing forward. Insert the Cap Screw
into the Outside Flange. Tighten the cap
screw using the provided Key Wrench.
Torque firmly (Approximately 100 in-lbs).
(Figure 1)
Note: Some units may have small holes in the attachments and/or pins on the spindle
shoulder. These are not used or required for this model.
9
OPERATION
Work Piece and Work Area Set Up
1. Designate a work area that is clean and well-lit. The work area must not allow access
by children or pets to prevent injury and distraction.
2. Route the Power Cord along a safe route to reach the work area without creating a
tripping hazard or exposing the Power Cord to possible damage. The Power Cord
must reach the work area with enough extra length to allow free movement while
working.
3. Secure loose work pieces using a vise or clamps (not included) to prevent movement
while working.
General Operating Instructions
1. The tool works by oscillating rapidly. Do not force the tool. Allow the tool to cut or
do its job.
2. Attachments may be mounted at angles up to 90° left or
right. The attachment should not turn on the spindle. If it
does, make sure that the cap screw is tight. Note: The long
Saw Blade should only be used in the straight ahead
position. (Figure 2)
3. Retract the Power Switch to its off position. Then connect
the tool into the nearest 120 volt, grounded electrical outlet.
4. To turn on the tool, slide the Power Switch forward.
5. Do not allow contact between the Sanding Paper, Scraper
Blade, or Saw Blade and work piece until the tool is running at full speed.
6. Avoid contact with foreign objects such as metal screws and nails when sanding,
scraping, or cutting.
7. Do not apply excessive pressure on the tool.
8. When finished, turn off the tool and allow it to completely stop before setting it down.
Then unplug the tool from its electrical outlet.
9. To replace the sanding paper, simply pull it off the pad. Prior to storing the tool,
remove the attachment and wipe it clean. Store the Tool in a clean, dry, safe location
out of reach of children and other unauthorized persons.
10
MAINTENANCE
Procedures not specifically explained in this manual must be performed only by a
qualified technician.
Warning: To Prevent Serious Injury From Accidental Operation:
Turn the power switch of the tool to its “OFF” position and unplug the tool from
its electrical outlet before performing any inspection, maintenance, or cleaning
procedures.
To prevent serious injury from tool failure:
1. Before each use, inspect the general condition of the tool. Check for loose screws,
misalignment or binding of moving parts, cracked or broken parts, damaged electrical
wiring, and any other condition that may affect its safe operation. The sanding paper
should not be dull or contain excessive debris build-up. The scraper blade and saw
Blade should be clean and sharp.
2. After Use, clean external surfaces of the tool with clean cloth.
Warning: If the power cord of this tool is damaged, it must be replaced only by
a qualified service technician.
11
TROUBLESHOOTING
Problem
Causes
Solutions
Tool will not start.
Power cord not connected.
Check that power cord is plugged in.
No power at outlet.
Check power at outlet. If outlet is
unpowered, turn off tool and check
circuit breaker.
Internal damaged or wear.
(carbon brush or switch)
Have technician service tool.
Attachment is
loose on the tool.
Holes on attachment not line
up with pins on spindle.
Remove the attachment and re-mount,
making sure that the holes in the
attachment are secured over the pins
on the spindle.
Screw (Part# 1) not tight
enough.
Tighten this screw to at least 100 inchlbs.
Tool operates
slowly.
Extension cord too long or
wire size too small.
Eliminate use of extension cord. If an
extension cord is needed, use
shorter/heavier gauge cord. See
ELECTRICAL INFORMATION
section.
Performance
decreases over
time.
Attachment dull or damaged.
Keep cutting accessories sharp.
Replace as needed.
Carbon brushes worn or
damaged.
Have technical replace brushes.
Excessive noise or
ratting.
Internal damage or wear.
Have technical service tool.
Overheating
Forcing tool to work.
Allow tool to work at its own rate.
Attachment dull or damaged.
Keep cutting accessories sharp.
Replace as needed.
Blocked motor housing
vents.
Blow dust out of motor using
compressed air.
12
EXPLODED VIEW
13
PARTS LIST
Part#
Stock#
Description
Part#
Stock#
Description
1
2310-001
Screw M8x12
24
2310-024
Stator
2
2310-002
Outside Flange
25
2310-025
Rubber Sleeve
3
2310-003
Blade
26
2310-026
Plastic Housing
4
2310-004
Spindle
27
2310-027
Power Cord
5
2310-005
Rubber Casing
28
2310-028
Link
6
2310-006
Circle Clip
29
2310-029
Cord Clip
7
2310-007
Spring Washer
30
2310-030
Screw ST4.0x14
8
2310-008
Bearing 6000
31
2310-031
Pull Brace
9
2310-009
Block
32
2310-032
Brush Cap
10
2310-010
Bronze Bushing
33
2310-033
Lug
11
2310-011
Screw ST4x27
34
2310-034
Brush Holder
12
2310-012
Reducer
35
2310-035
Spring
13
2310-013
Circle Clip
36
2310-036
Screw ST4.0x20
14
2310-014
Bearing 625
37
2310-037
Carbon Brush
15
2310-015
Sealing Washer
38
2310-038
Screw ST4.0x10
16
2310-016
Middle Cover
39
2310-039
Back Housing
17
2310-017
Bearing 608
40
2310-040
Screw ST4.0x27
18
2310-018
Balance Block
41
2310-041
Switch
19
2310-019
Armature
501
2310-501
Saw Blade
20
2310-020
Bearing 607
502
2310-502
Sanding Pad
21
2310-021
Rubber Bushing
503
2310-503
Half Moon Blade
22
2310-022
Fan Guide
504
2310-504
Sanding Paper
23
2310-023
Screw ST4.0x45
505
2310-505
Hex Wrench 6mm
14
WARRANTY STATEMENT
LIMITED ONE YEAR WARRANTY
WEN Products is committed to build tools that are dependable for years. Our warranties are consistent with
this commitment and our dedication to quality
LIMITED WARRANTY OF WEN CONSUMER POWER TOOLS PRODUCTS FOR HOME USE
GREAT LAKES TECHNOLOGIES, LLC ("Seller") warrants to the original purchaser only, that all WEN
consumer power tools will be free from defects in material or workmanship for a period of one (1) year
from date of purchase. Ninety days for all WEN products, if the tool is used for professional use.
SELLER'S SOLE OBLIGATION AND YOUR EXCLUSIVE REMEDY under this Limited Warranty and,
to the extent permitted by law, any warranty or condition implied by law, shall be the repair or replacement
of parts, without charge, which are defective in material or workmanship and which have not been misused,
carelessly handled, or misrepaired by persons other than Seller or Authorized Service Center. To make a
claim under this Limited Warranty, please contact us at 1-800-232-1195 or write to us at WEN Products,
501 Davis Road, Elgin, IL 60123. To acquire service, you will have to provide proof of purchase and may
be asked to ship the tool back to us freight prepaid.
THIS LIMITED WARRANTY DOES NOT APPLY TO ACCESSORY ITEMS SUCH AS CIRCULAR
SAW BLADES, DRILL BITS, ROUTER BITS, JIGSAW BLADES, SANDING BELTS, GRINDING
WHEELS AND OTHER RELATED ITEMS.
ANY IMPLIED WARRANTIES SHALL BE LIMITED IN DURATION TO ONE (1) YEAR FROM
DATE OF PURCHASE. SOME STATES IN THE U.S., SOME CANADIAN PROVINCES DO NOT
ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS, SO THE ABOVE
LIMITATION MAY NOT APPLY TO YOU.
IN NO EVENT SHALL SELLER BE LIABLE FOR ANY INCIDENTAL OR CONSEQUENTIAL
DAMAGES (INCLUDING BUT NOT LIMITED TO LIABILITY FOR LOSS OF PROFITS) ARISING
FROM THE SALE OR USE OF THIS PRODUCT. SOME STATES IN THE U.S. AND SOME
CANADIAN PROVINCES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL
OR CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT
APPLY TO YOU.
THIS LIMITED WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO
HAVE OTHER RIGHTS WHICH VARY FROM STATE TO STATE IN THE U.S., PROVINCE TO
PROVINCE IN CANADA AND FROM COUNTRY TO COUNTRY.
THIS LIMITED WARRANTY APPLIES ONLY TO PORTABLE ELECTRIC TOOLS, BENCH POWER
TOOLS, OUTDOOR POWER EQUIPMENT AND PNUMATIC TOOLS SOLD WITHIN THE UNITED
STATES OF AMERICA, CANADA AND THE COMMONWEALTH OF PUERTO RICO. FOR
WARRANTY COVERAGE WITHIN OTHER COUNTRIES, CONTACT THE WEN CUSTOMER
SUPPORT.
15
Loading...