Wells BMW-206ST Installation Manual

ELECTRICAL

BUILT-IN (BOTTOM MOUNT) INSULATED

MODEL VOLTS WATTS AMPS PHASE WIRING

BMW-206ST BMW-206ST

BMW-206ST BMW-206STD BMW-206STD BMW-206STD 240

120 1200 208 240 120 208

1240 1650 1200 1240 1650

10.0

6.0

6.9

10.0

6.0

6.9 SINGLE

SINGLE SINGLE SINGLE SINGLE SINGLE

#14 AWG Cu #14 AWG Cu #14 AWG Cu #14 AWG Cu #14 AWG Cu #14 AWG Cu

FIELD GAUGE

TEMP.

RATING

90°C MIN. 90°C MIN. 90°C MIN. 90°C MIN. 90°C MIN. 90°C MIN.

CUTOUT DETAILS PRODUCT DIMENSIONS

INSTALLATION INSTRUCTIONS

"SQUARE CORNER" FOOD WARMERS

MODELS BMW-206ST, STD

INCHES

(MM)

12 1/16

(306)

13 11/16

(348)

1/2

(13)

(MAX TURN DOWN)

7/8 (22)

SQUARE CORNERS

12 1/32

(306)

TOP CUTOUT

5/16

5/32

(4)

7/8 (22) 3/8

(10)

FRONT PANEL CUTOUT

(8)

2 1/32

(52)

5/32 (4)

PILOT LIGHT

20 1/16

(510)

20 3/32

(510)

8 5/16

(211)

CLEARANCES

SUGGESTED CLEARANCES FROM UNIT

TO THE NEAREST SURFACE

BACK SIDE BOTTOM FRONT

1 1

(25)

6 3/4

(171)

4 1/8

(105)

SEALANT

SEE CONDITIONS OF ACCEPTABILITY BELOW.

INSTALLATION INSTRUCTIONS

UNIT MUST BE INSTALLED IN AN ALL METAL COUNTER. THE INSTALLATION OF RECOGNIZED COMPONENT UNITS REQUIRES

ADDITIONAL EVALUATIONS TO UNDERWRITERS LABORATORIES INC. STANDARDS.

INSTALLER MUST MEET CONDITIONS OF ACCEPTABILITY OUTLINED BELOW UPON INSTALLATION:

1. This appliance shall be installed in an all metal counter with suitable wiring and control enclosures conforming to national and local electrical codes.

2. Electrical component temperatures, including wiring, within and surrounding the appliance must be monitored in the end use installation for suitability.

3. Electrical grounding of all dead metal parts must be reliably connected to the grounding means of the appliance and must comply with requirements outlined in the appropriate Underwriters Laboratories Inc. classification, national, and local electrical codes.

4. Increased clearances are required if storage of combustible materials is in close proximity to this appliance.

5. Unit shall be accessible for servicing from the bottom.

6. The name/rating plate information shall be accessible.

7. For water and waste connections: This appliance is to be installed to comply with the applicable federal, state or local plumbing codes.

WELLS/BLOOMFIELD * VERDI, NV

TO FABRICATE AND INSTALL:

1. Lay out cutout dimensions on countertop and apron.

2. Cut and/or drill holes as required in countertop and apron.

3. Turn down flange with square corners (maximum 1/2 inch).

4. To install, position warmer underneath so that turn down is positioned onto embossed shoulders of warmer. Drill as required.

5. Remove warmer and apply a bead of silicone sealant to shoulder area. Remount and secure warmer to fixture with stainless steel screws (see Detail "A" above).

6. Mount control to apron.

7. Connect supply connection wiring to thermostat. Check nameplate for correct voltage.

NOTE: The BMW-206STD warmer is supplied with a drain hole at one end and a 1/2 inch female N.P.T. drain nipple.

21 13/16

(554)

6 5/16

(160)

DETAIL 'A'

COUNTER-TOP

NO.8X5/8 LONG STAINLESS STEEL PAN HEAD SCREW. LOCK WASHER & NUT

4 1/8

(105)

1/2 IN DRAIN NPT BMW-206STD

NOTE: DRILL SCREW CLEARANCE HOLES IN ASSEMBLY SEAL HOLES AND FASTENERS WITH SILICONE SEALANT

46033-1 REV (A)

9 MIN

(229)

METAL SHIELD