QUESTIONS?
As a manufacturer, we are committed to providing complete
customer satisfaction. If you
have questions, or if there are
missing parts, we will guarantee
complete satisfaction through
direct assistance from our factory.
TO AVOID UNNECESSARY
DELAYS, PLEASE CALL DIRECT
TO OUR TOLL-FREE CUSTOMER
HOT LINE. The trained technicians on our customer hot line
will provide immediate assistance, free of charge to you.
CUSTOMER HOT LINE:
1-800-999-3756
Mon.–Fri., 6 a.m.–6 p.m. MST
Model No. WEBE19710
Serial No.
Write the serial number in the
space above for reference.
CAUTION
Read all precautions and instructions in this manual before
using this equipment. Save this
manual for future reference.
Serial Number Decal
USER’S MANUAL
Patent Pending
Visit our website at
www.weiderfitness.com
new products, prizes,
fitness tips, and much more!
WARNING DECAL PLACEMENT
WARNING DECAL PLACEMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
IMPORTANT PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
BEFORE YOU BEGIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
ADJUSTMENTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
EXERCISE GUIDELINES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
PART LIST . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
PART IDENTIFICATION CHART . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
EXPLODED DRAWING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
ORDERING REPLACEMENT PARTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Back Cover
LIMITED WARRANTY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Back Cover
The decal shown here
has been placed on the
weight rack. If the decal
is missing, or if it is not
legible, please call our
Customer Service
Department toll-free at
1-800-999-3756, Monday
through Friday, 6 a.m.
until 6 p.m. Mountain
Time, to order a free
replacement decal. Apply
the replacement decal in
the location shown.
WEIDER is a registered trademark of ICON Health & Fitness, Inc.
2
TABLE OF CONTENTS
IMPORTANT PRECAUTIONS
3
1. Read all instructions in this manual before
using the weight rack. Use the weight rack
only as described in this manual.
2. It is the responsibility of the owner to ensure
that all users of the weight rack are adequately informed of all precautions.
3. The weight rack is intended for home use
only. Do not use the weight rack in any commercial, rental, or institutional setting.
4. Use the weight rack only on a level surface.
Cover the floor beneath the weight rack to
protect the floor.
5. Make sure all parts are properly tightened
each time you use the weight rack. Replace
any worn parts immediately.
6. Keep children under 12 and pets away from
the weight rack at all times.
7. Always wear athletic shoes for foot protection while exercising.
8. Always make sure there is an equal amount
of weight on each side of your barbell. Note:
The weight rack does not include a barbell or
weights.
9. Do not place more than 210 pounds, including the barbell, on the weight rests. Do not
place more than 130 pounds on the weight
carriage.
Always place the same amount of
weight on each side of the weight carriage.
10. Always exercise with a partner. Your partner
should be ready catch the barbell if you cannot complete a repetition.
11. Always set both safety spotters and both
weight rests at the same height.
12.
Always disconnect the lat bar from the
weight rack when performing an exercise
that does not require the lat bar.
13. Make sure that the cables remain on the pulleys at all times. If the cables bind as you are
exercising, stop immediately and make sure
that the cables are on the pulleys.
14. When performing standing exercises, stand
inside the area that is shaded in the drawing
below.
15.
If you feel pain or dizziness at any time while
exercising, stop immediately and begin cooling down.
WARNING: Before beginning this or any exercise program, consult your physician. This
is especially important for persons over the age of 35 or persons with pre-existing health problems.
Read all instructions before using. ICON assumes no responsibility for personal injury or property
damage sustained by or through the use of this product.
WARNING: To reduce the risk of serious injury, read the following important precautions
before using the weight rack.
Thank you for selecting the versatile CLUB WEIDER
®
540 weight rack. The CLUB WEIDER®540 is designed
to help you develop every major muscle group of the
body. Whether your goal is a shapely figure, dramatic
muscle size and strength, or a healthier cardiovascular
system, the CLUB WEIDER
®
540 will help you achieve
the specific results you want.
For your benefit, read this manual carefully before
using the weight rack. If you have additional ques-
tions, please call our Customer Service Department
toll-free at 1-800-999-3756, Monday through Friday,
6 a.m. until 6 p.m. Mountain Time (excluding holidays).
To help us assist you, please note the product model
number and serial number before calling. The model
number is WEBE19710. The serial number can be
found on a decal attached to the weight rack (see the
front cover of this manual).
Before reading further, please review the drawing
below and familiarize yourself with the parts that are
labeled.
4
Weight Rest
Pull-up Bar
Safety Spotter
Front Upright
Rear Upright
Foot Plate
Right Side
Left Side
Lat Bar
High Pulley Station
Weight Guide
Weight Carriage
Low Pulley Station
Assembled
Dimensions:
Height: 86.5”
Base: 48” x 48”
BEFORE YOU BEGIN
Note: The terms “right side” and “left side” are
determined relative to a person standing with his
or her back to the rack; they do not correspond
to right and left on the drawings in the manual.
5
2
7
20
8
25
26
26
2. Attach the Foot Plate (8) and the Weight Base
(20) to the Center Base (7) using two M10 x
78mm Bolts (25) and two M10 Nylon Locknuts
(26). Do not tighten the Nylon Locknuts yet.
1
1. Press 60mm Square Outer Caps (19) onto the
ends of the Right and Left Bases (5, 6).
Attach the Right and Left Bases (5, 6) to the
Center Base (7) using four M10 x 78mm Bolts
(25) and four M10 Nylon Locknuts (26). Do not
tighten the Nylon Locknuts yet.
19
5
25
7
25
6
19
19
26
26
19
Before beginning assembly, carefully read the
following information and instructions:
• Assembly requires two people.
• For help identifying small parts, use the PART
IDENTIFICATION CHART on page 14.
• Tighten all parts as you assemble them, unless
instructed to do otherwise.
• As you assemble the weight rack, make sure all
parts are oriented as shown in the drawings.
• Place all parts in a cleared area and remove the
packing materials. Do not dispose of the packing
materials until assembly is completed.
The following tools (not included) are required
for assembly:
• Two adjustable wrenches
• One rubber mallet
• One standard screwdriver
• One Phillips screwdriver
• Lubricant, such as grease or petroleum jelly,
and soapy water.
Assembly will be more convenient if you have a
socket set, a set of open-end or closed-end
wrenches, or a set of ratchet wrenches.
Make Things Easier for Yourself
This manual is designed to ensure that the
weight rack can be assembled successfully by
anyone. Most people find that by setting aside
plenty of time, assembly will go smoothly.
ASSEMBLY
6
3
26
5
25
6
25
26
2
2
Adjustment
Holes
4. Tap a 2mm Thick 60mm Square Inner Cap (43)
into the top of each Front Upright (1).
Attach a Front Upright (1) and two Joint Plates (14)
to the Left Base (6) using four M10 x 78mm Bolts
(25) and four M10 Nylon Locknuts (26). Do not
tighten the Nylon Locknuts yet. Make sure that
the Front Upright is oriented so the holes near
the bottom of the Front Upright and the holes
in the Joint Plates line up. If they do not line
up, turn the Front Upright upside-down. Make
sure the Front Upright is turned so the adjustment holes are facing the Rear Upright (2).
Attach the other Front Upright (1) to the Right
Base (5) in the same manner.
43
25
5
1
6
14
14
1
26
26
12
26
1
26
25
5
14
14
25
1
4
3. Identify the two Rear Uprights (2), which are
slightly shorter and have less holes than the Front
Uprights (not shown).
Attach the Rear Uprights (2) to the Left and Right
Bases (5, 6) using four M10 x 78mm Bolts (25)
and four M10 Nylon Locknuts (26). Do not tight-
en the Nylon Locknuts yet. Make sure the
Uprights are oriented as shown, with the
adjustment holes on the indicated side near
the bottom.
Adjustment
Holes
5. Attach the Chin-up Bar (12) and two Joint Plates
(14) to the Front Uprights (1) using four M10 x
78mm Bolts (25) and four M10 Nylon Locknuts
(26). Do not tighten the Nylon Locknuts yet.
6
4
25
25
2
1
1
26
3
26
2
21
6. Press a 1.5mm Thick 60mm Square Inner Cap
(21) into the Left Frame (3). Attach the Left
Frame to the left Uprights (1, 2) using four M10 x
78mm Bolts (25) and four M10 Nylon Locknuts
(26). Do not tighten the Nylon Locknuts yet.
Assemble the Right Frame (4) to the right
Uprights (1, 2) in the same manner.
7
7
9. Press Weight Carriage Bushings (22) into the top
and bottom of the Weight Carriage (13). Press a
2” Round Inner Cap (36) into each end of the
weight tube on the Weight Carriage.
25
25
8
38
23
26
9
36
Weight Tube
36
22
22
13
30
25
9
4
3
26
26
26
24
20
21
11
Hole
10
26
13
40
26
11
25
Bracket
10. Insert the M10 x 19mm Bolt (40) into the bracket
on the Weight Carriage (13). Slide the Weight
Carriage onto the Weight Guide (11). Be sure the
Weight Carriage is turned so that the bracket
is at the top on the side shown.
Attach the Weight Frame (10) to the Weight
Guide (11) with two M10 x 78mm Bolts (25), two
M10 Washers (24), and two M10 Nylon Locknuts
(26).
Attach the Weight Frame (10) to the Center Frame
(9) with two M10 x 78mm Bolts (25), two M10
Washers (24), and two M10 Nylon Locknuts (26).
Do not tighten the M10 Nylon Locknuts (26)
yet.
24
25
9
24
24
24
10
7. Attach the Center Frame (9) to the Left and Right
Frames (3, 4) with four M10 x 78mm Bolts (25)
and four M10 Nylon Locknuts (26). Do not tight-
en the Nylon Locknuts yet.
8. Press a Weight Stop Bushing (30) into the top of
the Carriage Stop (23). Attach the Carriage Stop
to the indicated hole in the Weight Guide (11)
with an M10 x 86mm Bolt (38) and an M10 Nylon
Locknut (26).
Press a 1.5mm Thick 60mm Square Inner Cap
(21) into each end of the Weight Guide (11) (see
the inset drawing).
Attach the Weight Guide (11) to the Weight Base
(20) with two M10 x 78mm Bolts (25), two M10
Washers (24), and two M10 Nylon Locknuts (26).
Do not tighten the Nylon Locknuts yet.
21
11
8
14
13
34
29
27
28
26
39
12. Locate the Long Cable (34); note that there is a
single ball on one end of the Long Cable and a
metal sleeve on the other end.
Route the metal-sleeve end of the Long Cable
(34) up under the lat bar rest on the Weight
Frame (10) and over a 3 1/2” Pulley (27). Attach
the Pulley to the Weight Frame with an M10 x
75mm Bolt (31), two Short Spacers (32), two M10
Washers (24), and an M10 Nylon Locknut (26).
14 Wrap the Long Cable (34) around a 3 1/2” Pulley
(27) as shown. Attach the Pulley and a Cable
Trap (39) to the Pulley Plates (28) with an M10 x
45mm Bolt (29) and an M10 Nylon Locknut (26).
13. Route the Long Cable (34) over a 3 1/2” Pulley
(27) and down through the Weight Frame (10).
Attach the Pulley to the Weight Frame with an
M10 x 75mm Bolt (31), two Short Spacers (32),
two M10 Washers (24), and an M10 Nylon
Locknut (26).
31
24
27
24
26
32
32
34
10
Lat Bar
Rest
31
24
27
24
26
32
32
34
10
12
2
1
15
16
35
11. Insert the two Safety Spotters (16) into a set of
adjustment holes in the left and right Uprights (1, 2).
Wrap the locking pins around the Front Uprights.
Insert a 1” Round Inner Cap (35) into the end of
each Weight Rest (15).
Insert the two Weight Rests (15) into a set of
adjustment holes in the Front Uprights (1). Wrap
the locking pins around the Front Uprights.
Tighten all of the M10 Nylon Locknuts (26)
used in steps 1–10.
11
9
15. Route the Long Cable (34) up through the Weight
Frame (10), over a 3 1/2” Pulley (27), and back
down through the Weight Frame. Attach the
Pulley to the Weight Frame with an M10 x 75mm
Bolt (31), two Short Spacers (32), two M10
Washers (24), and an M10 Nylon Locknut (26).
15
31
24
27
24
26
32
32
34
10
16. Attach the metal-sleeve end of the Long Cable
(34) to the M10 x 19mm Bolt (40) on the Weight
Carriage (13) with an M10 Nylon Locknut (26).
Do not overtighten the Nylon Locknut; the
Cable must be able to pivot freely.
17. Locate the Short Cable (33); note that there are
two balls on one end of the Short Cable and a
metal sleeve on the other end.
Lay the ball-end of the Short Cable (33) inside the
bracket on the Center Base (7). Attach a 3 1/2”
Pulley (27) inside the bracket using an M10 x
45mm Bolt (29) and an M10 Nylon Locknut (26).
18. Wrap the Short Cable (33) around a 3 1/2” Pulley
(27) as shown. Attach the Pulley and a Cable
Trap (39) to the Pulley Plates (28) with an M10 x
45mm Bolt (29) and an M10 Nylon Locknut (26).
19. Attach the Short Cable (33) to the Weight Base
(20) with an M10 x 75mm Bolt (31), two M10
Washers (24), two Long Spacers (41), and an
M10 Nylon Locknut (26).
16
17
18
19
34
33
29
27
28
39
26
33
31
20
41
26
24
24
41
33
26
29
27
7
13
40
26
10
ADJUSTMENTS
This section explains how to adjust the weight rack. See the EXERCISE GUIDELINES on page 12 for important
information on how to get the most benefit from your exercise program. Also, refer to the accompanying exercise guide to see the correct form for each exercise.
Make sure all parts are properly tightened each time you use the weight rack. Replace any worn parts immediately. The weight rack can be cleaned with a damp cloth and a mild, non-abrasive detergent. Do not use solvents.
USING THE SAFETY SPOTTERS AND WEIGHT
RESTS
Before beginning an exercise, insert the Safety Spotters
(16) and the Weight Rests (15) into the sets of holes in
the Uprights (1, 2) that are best suited for that exercise.
The selected holes for the Safety Spotters should represent the lowest point to which you want the barbell to go
during the exercise. The selected holes for the Weight
Rests should be at a comfortable height for lifting and
replacing the barbell. Perform the exercise as shown in
the accompanying exercise guide. Note: Make sure the
locking clips on the Safety Spotters and Weight
Rests are wrapped around the Uprights.
WARNING:
Always set both Safety
Spotters (16) and both Weight Rests (15) at the
same height.
16
34
37
17
2
2
1
1
16
15
15
20
17
18
18
20. Wet the ends of the Lat Bar (17) with a small
amount of soapy water. Slide the Handgrips (18)
onto the ends of the Lat Bar.
21. Make sure all parts are properly tightened
before you use the weight rack. The use of all
remaining parts will be explained in
ADJUSTMENTS below.
ATTACHING THE LAT BAR OR WEIGHT STRAP TO
A PULLEY STATION
To use either pulley station, first place the desired
weights on the Weight Carriage (see ATTACHING
WEIGHTS TO THE WEIGHT CARRIAGE, on page
11). Next, attach the Lat Bar (17) or Weight Strap (not
shown) to the High Cable (34) or the Low Cable (not
shown) with a Cable Clip (37).
WARNING: Always disconnect the
Lat Bar (17) when performing an exercise that
does not require using the Lat Bar.
11
29
28
28
26
27
39
39
ATTACHING WEIGHTS TO THE WEIGHT CARRIAGE
To use the high or low pulley station, slide the desired
amount of weight onto the weight tube on the Weight
Carriage (13) and secure it with the Weight Clips (44).
13
44
44
Weight
Tube
WARNING:
Do not place more than
130 pounds on the Weight Carriage (13).
Always place the same amount of weight on
each side of the Weight Carriage. Always
secure the weights with the Weight Clips (44).
15
15
SETTING UP THE RACK FOR SQUAT EXERCISES
Squat exercises should be performed inside the rack
(behind the dotted line in the picture). When performing squat exercises, set the Safety Spotters (16) and
the Weight Rests (15) at a comfortable height.
Squat
Area
16
16
WARNING: Always move the
bench (not included) when you are performing
squat exercises inside the rack.
Weight
TIGHTENING THE CABLES
Woven cable, the type of cable used on the weight
rack, can stretch slightly after it is first used. If there is
slack in the cables, tighten them as described below.
Remove the M10 x 45mm Bolt (29) and the M10
Nylon Locknut (26) attaching the lower 3 1/2” Pulley
(27) and Cable Trap (39) to the two Pulley Plates
(28). Reattach the Pulley and Cable Trap to the higher set of holes in the Pulley Plates using the Bolt and
Nylon Locknut.
If moving just the lower 3 1/2” Pulley (27) does not
sufficiently tighten the cables, you can also move the
upper 3 1/2” Pulley down one set of holes in the
Pulley Plates (28).
12
EXERCISE GUIDELINES
THE FOUR BASIC TYPES OF WORKOUTS
Muscle Building
To increase the size and strength of your muscles,
push them close to their maximum capacity. Your muscles will continually adapt and grow as you progressively increase the intensity of your exercise. You can
adjust the intensity level of an individual exercise in
two ways:
• by changing the amount of weight used
• by changing the number of repetitions or sets performed. (A “repetition” is one complete cycle of an
exercise, such as one sit-up. A “set” is a series of
repetitions.)
The proper amount of weight for each exercise
depends upon the individual user. You must gauge
your limits and select the amount of weight that is right
for you. Begin with 3 sets of 8 repetitions for each
exercise you perform. Rest for 3 minutes after each
set. When you can complete 3 sets of 12 repetitions
without difficulty, increase the amount of weight.
Toning
You can tone your muscles by pushing them to a moderate percentage of their capacity. Select a moderate
amount of weight and increase the number of repetitions in each set. Complete as many sets of 15 to 20
repetitions as possible without discomfort. Rest for 1
minute after each set. Work your muscles by completing more sets rather than by using high amounts of
weight.
Weight Loss
To lose weight, use a low amount of weight and
increase the number of repetitions in each set.
Exercise for 20 to 30 minutes, resting for a maximum
of 30 seconds between sets.
Cross Training
Cross training is an efficient way to get a complete and
well-balanced fitness program. An example of a balanced program is:
• Plan weight training workouts on Monday,
Wednesday, and Friday.
• Plan 20 to 30 minutes of aerobic exercise, such as
cycling or swimming, on Tuesday and Thursday.
• Rest from both weight training and aerobic exercise
for at least one full day each week to give your body
time to regenerate.
The combination of weight training and aerobic exercise will reshape and strengthen your body, plus develop your heart and lungs.
PERSONALIZING YOUR EXERCISE PROGRAM
Determining the exact length of time for each workout,
as well as the number of repetitions or sets completed,
is an individual matter. It is important to avoid overdoing it during the first few months of your exercise program. You should progress at your own pace and be
sensitive to your body’s signals. If you experience pain
or dizziness at any time while exercising, stop immediately and begin cooling down. Find out what is wrong
before continuing. Remember that adequate rest and a
proper diet are important factors in any exercise program.
WARMING UP
Begin each workout with 5 to 10 minutes of stretching
and light exercise to warm up. Warming up prepares
your body for more strenuous exercise by increasing
circulation, raising your body temperature and delivering more oxygen to your muscles.
WORKING OUT
Each workout should include 6 to 10 different exercises. Select exercises for every major muscle group,
emphasizing areas that you want to develop most. To
give balance and variety to your workouts, vary the
exercises from session to session.
Schedule your workouts for the time of day when your
energy level is the highest. Each workout should be
followed by at least one day of rest. Once you find the
schedule that is right for you, stick with it.
EXERCISE FORM
Maintaining proper form is an essential part of an
effective exercise program. This requires moving
through the full range of motion for each exercise, and
moving only the appropriate parts of the body.
Exercising in an uncontrolled manner will leave you
feeling exhausted. On the exercise guide accompanying this manual you will find photographs showing the
correct form for several exercises, and a list of the
muscles affected. Refer to the muscle chart on page
13 to find the names of the muscles.
The repetitions in each set should be performed
smoothly and without pausing. The exertion stage of
each repetition should last about half as long as the
return stage. Proper breathing is important. Exhale
during the exertion stage of each repetition and inhale
during the return stroke. Never hold your breath.
13
Rest for a short period of time after each set. The
ideal resting periods are:
• Rest for three minutes after each set for a muscle
building workout.
• Rest for one minute after each set for a toning workout.
• Rest for 30 seconds after each set for a weight loss
workout.
Plan to spend the first couple of weeks familiarizing
yourself with the equipment and learning the proper
form for each exercise.
COOLING DOWN
End each workout with 5 to 10 minutes of stretching.
Include stretches for both your arms and legs. Move
slowly as you stretch and do not bounce. Ease into
each stretch gradually and go only as far as you can
without strain. Stretching at the end of each workout
is an effective way to increase flexibility.
STAYING MOTIVATED
For motivation, keep a record of each workout. List
the date, the exercises performed, the weight used,
and the numbers of sets and repetitions completed.
Record your weight and key body measurements at
the end of every month. Remember, the key to
achieving the greatest results is to make exercise a
regular and enjoyable part of your everyday life.
MUSCLE CHART
A. Sternomastoid (neck)
B. Pectoralis Major (chest)
C. Biceps (front of arm)
D. Obliques (waist)
E. Brachioradials (forearm)
F. Hip Flexors (upper thigh)
G. Abductor (outer thigh)
H. Quadriceps (front of thigh)
I. Sartorius (front of thigh)
J. Tibialis Anterior (front of calf)
K. Soleus (front of calf)
L. Rectus Abdominus (stomach)
M. Adductor (inner thigh)
N. Trapezius (upper back)
O. Rhomboideus (upper back)
P. Deltoid (shoulder)
Q. Triceps (back of arm)
R. Latissimus Dorsi (mid back)
S. Spinae Erectors (lower back)
T. Gluteus Medius (hip)
U. Gluteus Maximus (buttocks)
V. Hamstring (back of leg)
W. Gastrocnemius (back of calf)
A
B
C
D
E
G
H
I
J
K
F
M
L
T
N
O
P
Q
R
S
U
V
W
14
Note: “#” indicates a non-illustrated part. Specifications are subject to change without notice. See the back cover
of the user’s manual for information about ordering replacement parts.
Key No. Qty. Description Key No. Qty. Description
1 2 Front Upright
2 2 Rear Upright
3 1 Left Frame
4 1 Right Frame
5 1 Right Base
6 1 Left Base
7 1 Center Base
8 1 Foot Plate
9 1 Center Frame
10 1 Weight Frame
11 1 Weight Guide
12 1 Chin-up Bar
13 1 Weight Carriage
14 6 Joint Plate
15 2 Weight Rest
16 2 Safety Spotter
17 1 Lat Bar
18 2 Handgrip
19 4 60mm Square Outer Cap
20 1 Weight Base
21 4 1.5mm Thick 60mm Square Inner Cap
22 2 Weight Carriage Bushing
23 1 Carriage Stop
24 14 M10 Washer
25 40 M10 x 78mm Bolt
26 49 M10 Nylon Locknut
27 6 3 1/2” Pulley
28 2 Pulley Plate
29 3 M10 x 45mm Bolt
30 1 Weight Stop Bushing
31 4 M10 x 75mm Bolt
32 6 Short Spacer
33 1 Short Cable
34 1 Long Cable
35 2 1” Round Inner Cap
36 2 2” Round Inner Cap
37 2 Cable Clip
38 1 M10 x 86mm Bolt
39 2 Cable Trap
40 1 M10 x 19mm Bolt
41 2 Long Spacer
42 1 Weight Strap
43 2 2mm Thick 60mm Square Inner Cap
44 2 Weight Clip
45 4 Weight Clip Sleeve
# 1 User’s Manual
# 1 Exercise Guide
PART LIST—Model No. WEBE19710 R0801A
PART IDENTIFICATION CHART
Refer to the drawings below to identify small parts used in assembly. The number in parentheses by each drawing is the key number of the part from the PART LIST. Note: Some small parts may have been pre-attached.
If a part is not in the parts bag, check to see if it has been pre-attached.
M10 x 78mm Bolt (25)
M10 x 75mm Bolt (31)
M10 x 45mm Bolt (29)
M10 Washer (24)
M10 x 86mm Bolt (38)
M10 Nylon Locknut (26)
M10 x 19mm Bolt (40)
15
EXPLODED DRAWING—Model No. WEBE19710 R0801A
31
24
32
25
26
24
24
32
27
32
24
26
26
10
25
9
26
26
36
34
38
21
22
40
13
36
22
30
26
23
26
24
21
26
26
43
44
14
45
35
44
45
21
4
26
25
25
15
24
34
31
31
27
24
32
32
27
25
26
24
26
19
26
26
16
14
14
18
25
1
25
25
29
28
27
39
26
29
12
27
28
37
33
8
27
39
31
25
25
26
26
41
26
24
25
33
24
26
26
20
7
16
2
29
26
19
5
25
25
25
17
37
11
43
26
24
21
25
25
14
35
3
26
26
25
26
15
2
1
26
25
26
19
42
18
19
14
14
6
26
LIMITED WARRANTY
Part No. 176944 R0801A Printed in China © 2001 ICON Health & Fitness, Inc.
To order replacement parts, call our Customer Service Department toll-free at 1-800-999-3756, Monday through
Friday, 6 a.m. until 6 p.m. Mountain Time (excluding holidays). To help us assist you, please be prepared to give
the following information when calling:
1. The MODEL NUMBER of the product (WEBE19710)
2. The NAME of the product (CLUB WEIDER
®
540 weight rack)
3. The SERIAL NUMBER of the product (see the front cover of this manual)
4. The KEY NUMBER and DESCRIPTION of the desired part(s) (see the PART LIST and the EXPLODED
DRAWING on pages 14 and 15 of this manual).
ICON Health & Fitness, Inc. (ICON), warrants this product to be free from defects in workmanship and material, under normal use and service conditions, for a period of ninety (90) days from the date of purchase. This
warranty extends only to the original purchaser. ICON's obligation under this warranty is limited to replacing
or repairing, at ICON's option, the product at one of its authorized service centers. All products for which warranty claim is made must be received by ICON at one of its authorized service centers with all freight and other
transportation charges prepaid, accompanied by sufficient proof of purchase. All returns must be pre-authorized by ICON. This warranty does not extend to any product or damage to a product caused by or attributable to freight damage, abuse, misuse, improper or abnormal usage or repairs not provided by an ICON
authorized service center, products used for commercial or rental purposes, or products used as store display
models. No other warranty beyond that specifically set forth above is authorized by ICON.
ICON is not responsible or liable for indirect, special or consequential damages arising out of or in connection
with the use or performance of the product or damages with respect to any economic loss, loss of property,
loss of revenues or profits, loss of enjoyment or use, costs of removal, installation or other consequential damages of whatsoever nature. Some states do not allow the exclusion or limitation of incidental or consequential damages. Accordingly, the above limitation may not apply to you.
The warranty extended hereunder is in lieu of any and all other warranties and any implied warranties of merchantability or fitness for a particular purpose is limited in its scope and duration to the terms set forth herein.
Some states do not allow limitations on how long an implied warranty lasts. Accordingly, the above limitation
may not apply to you.
This warranty gives you specific legal rights. You may also have other rights which vary from state to state.
ICON HEALTH & FITNESS, INC., 1500 S. 1000 W., LOGAN, UT 84321-9813
ORDERING REPLACEMENT PARTS
Loading...