Page 1
R Trademark
Please do not return unit to retailer.
Por favor, no devuelva el aparato al lugar de compra.
Veuillez ne p as retourner l’outil au détaillant.
1-800-554-6723
www.weedeater.com
Instruction Manual
Manual de Instrucciones
Manuel d’Instructions
FL1500
ENGLISH ESPAÑOL
For Household Use Only
WARNING:
Read and follow all Safety Rules and Operating Instructions before
using this product. Failure to do so can result in serious injury.
ADVERTENCIA:
Lea el manual de instrucciones y siga todas las advertencias e
instrucciones de seguridad. El no hacerlo puede resultar en lesiones
graves.
A VERTISSEMENT:
Lire le manuel d’instructions et bien respecter tous les avertissements et toutes les instructions de sécurité. Tout défaut de le faire
pourrait entraîner des blessures graves.
Electrolux Home Products, Inc.
250 Bobby Jones Expressway
Augusta, GA 30907
CopyrightE2002 Electrolux Home Products, Inc.
530088117 4/23/02
FRANÇAIS
Page 2
SAFETY RULES
WARNING:
Safety Rules and Precautions can result in
serious injury.
KNOW YOUR UNIT
Read your instruction manual carefully until
S
you completely understand and can follow
all warnings and safety rules before operating the unit.
D
Restrict unit to users who understand and
will follow all warnings and safety rules in
this manual.
WARNING:
starting the unit. Remove all debris and hard
objects such as rocks, glass, wire, etc. that
can ricochet, be thrown, or otherwise cause
injury or damage during operation.
Use your unit as a blower for:
D
Sweeping debris or grass clippings from
driveways, sidewalks, patios, etc.
Blowing grass clippings, straw, or leaves
S
into piles, around joints, or between bricks.
PLAN AHEAD
D
Always wear eye protection when operating,
servicing, or performing maintenance on unit.
Wearing eye protection will help to prevent
rocks or debris from being blown or ricocheting into eyes and face which can result in
blindness and/or serious injury. Eye protection should be marked Z87.
D
Always wear foot protection. Do not go
barefoot or wear sandals.
D
Always wear respirator or face mask when
working with unit in dusty environments.
D
Secure hair above shoulder length. Secure or
remove jewelry, loose clothing, or clothing
with loosely hanging straps, ties, tassels, etc.
They can be caught in moving parts.
D
Do not operate unit when you are tired, ill, upset, or if you are under the influence of alcohol, drugs, or medication.
D
Keep children, bystanders, and animals
away from work area a minimum of 30 feet
(10 meters) when starting or operating unit.
Do not point blower nozzle in the direction
of people or pets.
HANDLE FUEL WITH CAUTION, IT IS
HIGHLY FLAMMABLE
D
Eliminate all sources of sparks or flame (including smoking, open flames, or work that
can cause sparks) in the areas where fuel is
mixed, poured, or stored.
D
Mix and pour fuel in an outdoor area; store
fuel in a cool, dry, well ventilated place; use
an approved, marked container for all fuel
purposes.
D
Do not smoke while handling fuel or while
operating the unit.
D
Make sure the unit is properly assembled
and in good operating condition.
D
Do not fill fuel tank while engine is running.
D
Avoid spilling fuel oroil. Wipe up fuel spills before starting engine.
Failure to follow all
Inspect the area before
-- 2 --
D
Move at least 10 feet (3 meters) away from
fuel and fueling site before starting engine.
D
Always store gasoline in a container approved for flammable liquids.
OPERATE YOUR UNIT SAFELY
D
Inspect unit before each use for worn,
loose, missing, or damaged parts. Do not
use until unit is in proper working order.
D
Keep outside surfaces free from oil and
fuel.
D
Never start or run engine inside a closed
room, building or other unventilated area.
Breathing exhaust fumes can kill.
D
To avoid static electricity shock, do not
wear rubber gloves or any other insulated
gloves while operating unit.
D
Do not set unit on any surface except a
clean, hard area while engine is running.
Debris such as gravel, sand, dust, grass,
etc. could be picked up by the air intake and
thrown out through discharge opening,
damaging unit, property, or causing serious
injury to bystanders or operator.
D
Avoid dangerous environments. Do not use
in unventilated areas or where explosive
vapors or carbon monoxide build up could
be present.
D
Do not overreach or use from unstable surfaces such as ladders, trees, steep slopes,
rooftops, etc. Keep firm footing and balance
at all times.
D
Never place objects inside the blower
tubes; always direct the blowing debris
away from people, animals, glass, and solid
objects such as trees, automobiles, walls,
etc. The force of aircan causerocks, dirt, or
sticks to be thrown or to ricochet which can
hurt people or animals, break glass, or
cause other damage.
D
Never run unit without the proper equipment attached. When using your unit as a
blower, always install blower tube.
D
Check air intake opening and blower
tubes, frequently, always with engine
stopped and spark plug disconnected.
Keep vents and discharge tubes free from
debris which can accumulate and restrict
proper air flow and cause damage to the
unit.
D
Never use for spreading chemicals, fertilizers, or other substances which may contain toxic materials.
D
To avoid spreading fire, do not use near
leaf or brush fires, fireplaces, barbecue
pits, ashtrays, etc.
D
Use only for jobs explained in this manual.
MAINTAIN YOUR UNIT PROPERLY
D
Have all maintenance other than the recommended procedures described in the instruction manual performed by an authorized service dealer.
D
Disconnect spark plug before performing
maintenance except for carburetor adjustments.
Page 3
D
Use only recommended Weed Eate r!parts;
use of any other parts may void your warranty and cause damage to your unit.
D
Empty the fuel tank before storing the unit.
Use up fuel left in carburetor by starting the
engine and letting it run until it stops.
D
Do not use any accessory or attachment
other than those recommended by the
manufacturer for use with your unit.
D
Do not store the unit or fuel in a closed area
where fuel vapors can reach sparks or an
open flame from hot water heaters, electric
motors or switches, furnaces, etc.
D
Store in a dry area out of reach of children.
SPECIAL NOTICE:
est Land and in some states, including California(Public Resources Codes 4442 and
4443), Idaho, Maine, Minnesota, New Jersey,
Oregon, and Washington: Certain internal
combustion engines operated on forest,
brush, and/or grass covered land in the above
areas are required to be equipped with a
spark arresting screen, maintained in effective working order, or the engine must be constructed, equipped, and maintained for the
prevention of fire. Check with your state or local authorities for regulations pertaining to
For users on U.S. For-
ASSEMBLY
It is normal for the fuel filter to rattle in
NOTE:
the empty fuel tank.
ASSEMBLY
WARNING:
repeat all steps to ensure your unit is properly
assembled and all fasteners are secure.
Follow all safety information in the manual
and on the unit.
D
No tools are required for assembly.
If received assembled,
these requirements. Failure to follow these
requirements is a violation of the law. This unit
is not factory equipped with a spark arresting
screen; however, a spark arresting screen is
available as an optional part. If a spark arresting screen is required in your area, contact an
authorized service dealer for the correct kit.
The spark arresting screen, blower tubes,
and nozzles must be assembled to unit to be
in full compliance with regulations.
SPECIAL NOTICE:
through prolonged use of gasoline powered
hand tools could cause blood vessel or nerve
damage in the fingers, hands, and joints of people prone to circulation disorder s or abnormal
swelling. Prolonged use in cold weather has
been linked to blood vessel damage in otherwise healthy people. If symptoms occur such as
numbness, pain, loss of strength, change in skin
color or texture, or loss of feeling in the fingers,
hands, or joints, discontinue the use of this tool
and seek medical attention. An anti- vibration
system does not guarantee the avoidance of
these problems. Users who operate power tools
on a continual and regular basis must monitor
closely their physical condition and the condition
of this tool.
Exposure to vibrations
BLOWER TUBE
D
Push the blower tube into the blower outlet
until it snaps into place.
Blower Outlet
Blower Tube
OPERATION
KNOW YOUR BLOWER
READ THIS INSTRUCTION MANUAL AND SAFETY RULES BEFORE OPERATING YOUR
UNIT. Compare the illustrations with your unit to familiarize yourself with locations of the various
controls and adjustments. Save this manual for future reference.
Primer Bulb
Blower Tube
-- 3 --
Fuel Cap
Choke
Lever
Page 4
PRIMER BULB
The PRIMER BULB removes air from the carburetor and fuel lines and fills them with fuel.
This allows you to start the engine with fewer
pulls on the starter rope. Activate the primer
bulb by pressing it and allowing it to return to
its original form.
CHOKE LEVER
The CHOKE helps to supply fuel to the engine
to aid in cold starting. The RUN position is
used for full speed operation. The 1/2 position
is used for a brief initial warm-up period and to
set the engine at idle speed.
OPERATING TIPS
To reduce the risk of hearing loss associat-
S
ed with sound level(s), hearing protection is
required.
Operate power equipment only at reasonable
S
hours--not early in the morning or late at night
when people might be disturbed. Comply with
times listed in local ordinances. Usual recommendations are 9:00 a.m. to 5:00 p.m.,
Monday though Saturday.
To reduce noise levels, operate power
S
blowers at the lowest possible throttle
speed to do the job.
To reduce noise levels, limit the number of
S
pieces of equipment used at any one time.
Use rakes and brooms to loosen debris be-
S
fore blowing.
In dusty conditions, slightly dampen sur-
S
faces when water is available.
Conserve water by using power blowers
S
instead of hoses for many lawn and garden
applications, including areas such as gutters,
screens, patios, grills, porches, and gardens.
Watch out for children, pets, open windows,
S
or freshly washed cars. Blow debris away
safely.
Use the full blower nozzle extension so the
S
air stream can work close to the ground.
After using blowers and other equipment,
S
CLEAN UP! Dispose of debris in trash receptacles.
BEFORE STARTING ENGINE
WARNING:
information in the safety rules before you
begin. If you do not understand the safety
rules, do not attempt to fuel your unit. Call
1-800-554-6723.
Be sure to read the fuel
FUELING ENGINE
WARNING:
when refueling.
This engine is certified to operate on unleaded gasoline. Before operation, gasoline
must be mixed with a good quality synthetic
2-cycle air-cooled engine oil designed to be
mixed at a ratio of 40:1. Poulan/W eed Eaterbrand synthetic oil is recommended. Mix gasoline and oil at a ratio of 40:1. A 40:1 ratio is
obtained by mixing 3.2 ounces of oil with 1
gallon of unleaded gasoline. DO NOT USE
automotive oil or boat oil. These oils will cause
engine damage. When mixing fuel, follow
instructions printed on container. Once oil is
added to gasoline, shake container momentarily to assure that the fuel is thoroughly
mixed. Always read and follow the safety
rules relating to fuel before fueling your unit.
Remove fuel cap slowly
-- 4 --
IMPORTANT
Experience indicates that alcohol blended
fuels (called gasohol or using ethanol or
methanol) can attract moisture which leads to
separation and formation of acids during storage. Acidic gas can damage the fuel system
of an engine while in storage. To avoid engine
problems, empty the fuel system before storage for 30 days or longer. Drain the gas tank,
start the engine and let it run until the fuel lines
and carburetor are empty. Use fresh fuel next
season. Never use engine or carburetor
cleaner products in the fuel tank orpermanent
damage may occur.
OPERATING
POSITION
Eye
Protection
STOPPING YOUR ENGINE
D
To stop the engine, move the choke lever to
the START/STOP position.
BEFORE STARTING THE ENGINE
WARNING:
the tube is secure before using the unit.
D
Fuel engine. Move at least 10 feet (3 meters) away from the fueling site.
D
Hold the unit in the starting position as
shown. Make sure the blower end is directed away from people, animals, glass,
and solid objects.
You MUST make sure
STARTING
POSITION
WARNING:
hold the unit as illustrated. Do not set unit on
any surface except a clean, hard area when
starting engine or while engine is running.
Debris such as gravel, sand, dust, grass, etc.
could be picked up by the air intake and
thrown out through the discharge opening,
When starting engine,
Page 5
damaging the unit or property, or causing
serious injury to bystanders or the operator.
Primer
Bulb
Choke Lever
STARTING A COLD ENGINE (or a
warm engine after running out of
fuel)
1. Move choke lever to START/STOP.
2. Slowly press the primer bulb 6 times.
3. Sharply pull starter handle until engine attempts to run. NO MORE THAN 5 PULLS.
4. Move choke lever to 1/2 CHOKE. Pull
starter rope sharply until engine runs.
MAINTENANCE
GENERAL RECOMMENDATIONS
The warranty onthis unit does not cover items
that have been subjected to operator abuse
or negligence. To receive full value from the
warranty, the operator must maintain unit as
instructed in this manual. Various adjustments will need to be made periodically to
properly maintain your unit.
CHECK FOR LOOSE
FASTENERS AND PARTS
Spark Plug Boot
S
Air Filter
S
Housing Screws
S
CHECK FOR DAMAGED OR
WORN PARTS
Contact an authorized service dealer for replacement of damaged or worn parts.
Choke Lever -- Ensure choke lever func-
S
tions properly by moving to the START/
STOP position. Make sure engine stops;
then restart engine and continue.
Fuel Tank -- Discontinue use of unit if fuel
S
tank shows signs of damage or leaks.
INSPECT AND CLEAN UNIT AND
DECALS
After each use, inspect complete unit for
S
loose or damaged parts. Clean the unit using a damp cloth with a mild detergent.
Wipe off unit with a clean dry cloth.
S
If engine has not started after 5 pulls,
NOTE:
repeat all of the above steps.
5. After a 10 second warm-up, move the
choke lever to RUN.
6. To stop engine, move the choke lever to
the START/STOP position.
STARTING A WARM ENGINE
1. Move the choke lever to the RUN position
2. Pull starter handle sharply until engine
runs.
NOTE:
follow information provided under STARTING
ACOLDENGINE.
If engine does not run after 5 pulls,
DIFFICULT STARTING (or starting a
flooded engine)
Flooded engines can be started by placing the
choke lever in the RUN position; then, pull the
starter handle sharply to clear the engine of excess fuel. This could require pulling the starter
handle many times depending on how badly the
unit is flooded.
If the unit still does not start, refer to
TROUBLESHOOTING TABLE or call
1-800-554-6723
.
CLEAN AIR FILTER
Air Filter
Screw
Air Filter Cover
Cleaning the air filter:
A dirty air filter decreases engine performance and increases fuel consumption and
harmful emissions. Always clean after every
5 hours of operation.
1. Clean the cover and the area around it to
keep debris from falling into the carburetor
chamber when the cover is removed.
2. Remove parts as illustrated.
Do not clean filter in gasoline or other
NOTE:
flammable solvent. Doing so can create a fire
hazard or produce harmful evaporative emissions.
3. Wash the filter in soap and water.
4. Allow filter to dry.
5. Apply a few drops of oil to the filter;
squeeze filter to distribute oil.
6. Replace parts.
.
-- 5 --
Page 6
REPLACE SPARK PLUG
Replace spark plug each year to ensure the
engine starts easier and runs better. Set
spark plug gap at 0.025 inch. Ignition timing is
fixed, nonadjustable.
1. Twist, then pull off spark plug boot.
2. Remove spark plug from cylinder and discard.
3. Replace with Champion RCJ-6Y spark
plug and tighten securely with a 3/4 inch
socket wrench.
4. Reinstall the spark plug boot.
STORAGE
WARNING:
steps after each use:
Allow engine to cool, and secure the unit
S
before storing or transporting.
Store unit and fuel in a well ventilated area
S
where fuel vapors cannot reach sparks or
open flames from water heaters, electric
motors or switches, furnaces, etc.
Store unit with all guards in place. Position
S
unit so that any sharp object cannot accidentally cause injury.
Store unit and fuel well out of the reach of
S
children.
SEASONAL STORAGE
Prepare unit for storage at end of season or if
it will not be used for 30 days or more.
If your unit is to be stored for a period of time:
Clean the entire unit before lengthy stor-
S
age.
Store in a clean dry area.
S
Lightly oil external metal surfaces.
S
FUEL SYSTEM
Under FUELING ENGINE in the OPERATION section of this manual, see message labeled IMPORTANT regarding the use of gasohol in your engine.
Perform the following
CARBURETOR ADJUSTMENTS
Your carburetor is equipped with limiter caps.
Damage will occur if you turn the needles beyond the limiter caps. Carburetor adjustment is
a complicated task. We recommend that you
take your unit to an authorized service dealer.
Fuel stabilizer is an acceptable alter n ativ e in
minimizing the formation of fuel gum deposits
during storage. Add stabilizer to gasoline in fuel
tank or fuel storage container . Follow the mix
instructions found on stabilizer container. Run
engine at least 5 minutes after adding stabilizer.
ENGINE
Remove spark plug and pour 1 teaspoon of
S
40:1, 2-cycle engine oil (air cooled) through
the spark plug opening. Slowly pull the
starter rope 8 to 10 times to distribute oil.
Replace spark plug with new one of recom-
S
mended type and heat range.
Clean air filter.
S
Check entire unit for loose screws, nuts,
S
and bolts. Replace any damaged, broken,
or worn parts.
At the beginning of the next season, use
S
only fresh fuel having the proper gasoline to
oil ratio.
OTHER
Do not store gasoline from one season to
S
another.
Replace your gasoline can if it starts to rust.
S
-- 6 --
Page 7
TROUBLESHOOTING TABLE
WARNING:
recommended remedies below other than remedies that require operation of the unit.
TROUBLE
Engine will not
start.
Engine will not
idle properly.
Engine will not
accelerate,
lacks power, or
dies under a
load.
Engine smokes
excessively.
Engine runs hot.
Always stop unit and disconnect spark plug before performing any of the
CAUSE REMEDY
1. Engine flooded.
2. Fuel tank empty.
3. Spark plug not firing.
4. Fuel not reaching
carburetor.
5. Compression low.
1. Fuel not reaching
carburetor.
2. Carburetor requires
adjustment.
3. Crankshaft seals worn.
4. Compression low.
1. Air filter dirty.
2. Fuel not reaching
carburetor.
3. Spark plug fouled.
4. Carburetor requires
adjustment.
5. Carbon build up.
6. Compression low.
1. Choke partially on.
2. Fuel mixture incorrect.
3. Air filter dirty.
4. Carburetor requires
adjustment.
1. Fuel mixture incorrect.
2. Spark plug incorrect.
3. Carburetor requires
adjustment.
4. Carbon build up.
1. See “Starting a Flooded Engine”
in Operation section.
2. Fill tank with correct fuel mixture.
3. Install new spark plug.
4. Check for dirty fuel filter; replace.
Check for kinked or split fuel line;
repair or replace.
5. Contact an authorized service dealer.
1. Check for dirty fuel filter; replace.
Check for kinked or split fuel line;
repair or replace.
2. See “Carburetor Adjustment” in
Service and Adjustments section.
3. Contact an authorized service dealer
4. Contact an authorized service dealer.
1. Clean or replace air filter.
2. Check for dirty fuel filter; replace.
Check for kinked or split fuel line;
repair or replace.
3. Clean or replace spark plug
and re-gap.
4. See “Carburetor Adjustment” in
Service and Adjustments section.
5. Contact an authorized service dealer.
6. Contact an authorized service dealer.
1. Adjust choke.
2. Empty fuel tank and refill with
correct fuel mixture.
3. Clean or replace air filter.
4. See “Carburetor Adjustment” in
Service and Adjustments section.
1. See “Fueling Engine” in Operation
section.
2. Replace with correct spark plug.
3. See “Carburetor Adjustment” in
Service and Adjustments section.
4. Contact an authorized service dealer.
-- 7 --
Page 8
LIMITED WARRANTY
ELECTROLUX HOME PRODUCTS, INC.,
warrants to the original purchaserthat each new
Weed Eater brand gasoline tool or attachment
is free from defects in material and workmanship and agrees to repair or replace under this
warranty any defective gasoline product or attachment as follows from the original date of
purchase.
2YEARS--Parts and Labor, when used for
household purposes.
90 DAYS--Parts and Labor, when used for
commercial, professional, or income producing purposes.
30 DAYS--Parts and Labor, if used for rental
purposes.
This warranty is not transferable and does not
cover damage or liability caused by impr oper
handling, improper maintenance, or the use of
accessories and/or attachments not specifically
recommended by ELECTROLUX HOME
PRODUCTS, INC., for this tool. Additionally,
this warr anty does not cover tune-ups, spark
plugs, filters, etc., that will wear and require replacement with reasonable use during the warranty period. This warranty does not cover pre-
U.S. EPA
EMISSION CONTROL WARRANTY STATEMENT
YOUR WARRANTY RIGHTS AND OBLIGATIONS: The U. S. Environmental
Protection Agency and POULAN/WEED
EATER, DIVISION OF WCI OUTDOOR
PRODUCTS, INC., are pleased to explain the
emissions control system warranty on your
year 2001--2004 small off--road engine.
POULAN/WEED EATER must warrant the
emission control system on your small off-road engine for the periods of time listed below provided there has been no abuse, neglect, or improper maintenance of your small
off--road engine. Your emission control system includes parts such as the carburetor and
the ignition system. Where a warrantable
condition exists, POULAN/WEED EATER
will repair your small off--road engine at no
cost to you. Expenses covered under warranty include diagnosis, parts and labor.
MANUFACTURER’S WARRANTY COVERAGE:If any emissions related part on your
engine (as listed under Emissions Control
Warranty Parts List) is defective or a defect in
the materials or workmanship of the engine
causes the failure of such an emission related
part, the part will be repaired or replaced by
POULAN/WEED EATER. OWNER’S WAR-
RANTY RESPONSIBILITIES: As the small
off--road engine owner, you are responsible
for the performance of the required maintenance listed in your instruction manual. POULAN/WEED EATER recommends that you
retain all receipts covering maintenance on
your small off--road engine, but POULAN/
WEED EATER cannot deny warranty solely
for the lack of receipts or for your failure to en-
-- 8 --
delivery setup or normal adjustments explained
in the instruction manual.
THIS WARRANTY GIVES YOU SPECIFIC
LEGAL RIG HTS, AND YOU MAY HAVE
OTHER RIGHTS WHICH VARY FROM
STATE TO STA TE.
NO CLAIMS FOR CONSEQUENTIAL OR
OTHER DAMAGES WILL BE ALLOWED,
AND THERE ARE NO OTHER EXPRESS
WARRANTIES EXCEPT THOSE EXPRESSLY STIPULATED HEREIN.
SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS OR THE EXCLUSION OR
LIMITATIONS OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE
LIMITATIONS OR EXCLUSION MAY NOT
APPLY TO YOU.
The policy of ELECTROLUX HOME PROD-
UCTS, INC., is to continuously improve its
products. Therefore, ELECTROLUX HOME
PRODUCTS, INC., reserves the right to
change, modify, or discontinue models, designs, specifications, and accessories of all
products at any time without notice or obligation to any purchaser.
sure the performance of all scheduled maintenance. As the small off--road engine owner, you should be aware that POULAN/
WEED EATER may deny you warranty coverage if your small off--road engine or a part of
it has failed due to abuse, neglect, improper
maintenance, unapproved modifications, or
the use of parts not made or approved by the
original equipment manufacturer. You are responsible for presenting your small off--road
engine to a POULAN/WEED EATER authorized repair center as soon as a problem exists. Warranty repairs should be completed in
a reasonable amount of time, not to exceed
30 days. If you have any questions regarding
your warranty rights and responsibilities, you
should contact your nearest authorized service center or call POULAN/WEED EATER at
1--800 --554--6723. WARRANTY COM-
MENCEMENT DATE: The warranty period
begins on the date the small off--road engine
is purchased. LENGTH OF COVERAGE:
This warranty shall be for a period of two
years from the initial date of purchase. WHA T
IS COVERED: REPAIR OR REPLACEMENT OF PARTS. Repair or replacement of
any warranted part will be performed at no
charge to the owner at an approved POULAN/WEED EATER servicing center. If you
have any questions regarding your warranty
rights and responsibilities, you should contact
your nearest authorized service center or call
POULAN/WEED EATER at
1--800 --554--6723. WARRANTY PERIOD:
Any warranted part which is not scheduled for
replacement as required maintenance, or
Page 9
which is scheduled only for regular inspection
to the effect of ”repair or replace as necessary” shall be warranted for 2 years. Any warranted part which is scheduled for replacement as required maintenance shall be warranted for the period of time up to the first
scheduled replacement point for that part.
DIAGNOSIS: The owner shall not be
charged for diagnostic labor which leads to
the determination that a warranted part is defective if the diagnostic work is performed at
an approved POULAN/WEED EATER servicing center. CONSEQUENTIAL DAM-
AGES: POULAN/WEED EATER may be liable for damages to other engine components caused by the failure of a warranted
part still under warranty. WHAT IS NOT
COVERED: All failures caused by abuse, neglect, or improper maintenance are not covered. ADD--ON OR MODIFIED PARTS: The
use of add --on or modified parts can be
grounds for disallowing a warranty claim.
POULAN/WEED EATER is not liable to cover
failures of warranted parts caused by the use
This engine is certified to be emissions compliant for the following use:
Moderate (50 hours)
Intermediate (125 hours)
Extended (300 hours)
of add--on or modified parts. HOW TO FILE A
CLAIM: If you have any questions regarding
your warranty rights and responsibilities, you
should contact your nearest authorized service center or call POULAN/WEED EATER at
1--800 --554--6723. WHERE TO GET WAR-
RANTY SERVICE: Warranty services or repairs shall be provided at all POULAN/WEED
EATER service centers. Call
1--800 --554--6723. MAINTENANCE, RE-
PLACEMENT AND REPAIR OF EMISSION
RELATED PARTS: Any POULAN/WEED
EATER approved replacement part used in
the performance of any warranty maintenance or repair on emission related parts will
be provided without charge to the owner if the
part is under warranty. EMISSION CON-
TROL WARRANTY PARTS LIST: Carburetor, Ignition System: Spark Plug (covered up
to maintenance schedule), Ignition Module.
MAINTENANCE STATEMENT:The owner is
responsible for the performance of all required mainten ance as defined in the instruction manual.
-- 9 --
Loading...