R
Please do not return unit to retailer.
Por favor, no devuelva el aparato al lugar de compra.
Veuillez ne pas retourner l’outil au détaillant.
1-800-554-6723
www.weedeater.com
Instruction Manual
Manual de Instrucciones
Manuel d’Instructions
ENGLISH ESPAÑOL
Trademark
TWIST--N--EDGE
TE 400 LE
For Occasional Use Only
WARNING:
Read and follow all Safety Rules and Operating Instructions before
using this product. Failure to do so can result in serious injury.
ADVERTENCIA:
Lea el manual del operador y siga todas las advertencias e instrucciones de seguridad. El no hacerlo puede resultar en lesiones graves.
A VERTISSEMENT:
Lire le manuel de l’utilisateur et bien respecter tous lesavertissements et toutes les instructions de sécurité. Tout défaut de le
faire pourrait entraîner des blessures graves.
Electrolux Home Products, Inc.
250 Bobby Jones Expressway
Augusta, GA 30907
CopyrightE2002 Electrolux Home Products, Inc.
530086412
4/24/02
t
FRANÇAIS
SAFETY RULES
WARNING:
appliances, basic safety precautions should
always be followed to reduce the risk of fire
and serious injury. Read and follow all
instructions.
This power unit can be dangerous!
responsible for following unit and manual
instructions and warnings. Read entire instruction manual before using unit! Be thoroughly familiar with the controls and the proper use of the
unit. Restrict the use of this unit to persons who
read, understand, and follow unit and manual
instructions and warnings. Never allow children
to operate this unit.
INSTRUCTION
MANUAL
DANGER:
flailing devices. This unit is designed for line
trimmer use only. Use of any other accessories or attachments will increase the risk of
injury.
WARNING:
jects violently . You and others can be blinded/
injured. Wear safety glasses and leg protection. Keep body parts clear of rotating line.
Safety Glasses or similar eye protection
Boots
Keep children, bystanders, and animals 50 feet
(15 meters) away. If approached stop unit immediately.
If situations occur which are not covered in
this manual, use care and good judgement. If
you need assistance, contact your authorized
service dealer or call 1-800-554-6723.
OPERATOR SAFETY
Dress properly. Always wear safety
S
glasses or similar eye protection when operating, or performing maintenance, on
your unit (safety glasses are available).
Eye protection should be marked Z87.
Always wear face or dust mask if operation
S
is dusty.
When using gardening
Operator is
SAFETY INFORMATION
ON THE UNIT
Never use blades, wire or
Trimmer line throws ob-
Hazard Zone
50 ft.
(15 m)
Always wear heavy, long pants, long
S
sleeves, boots, and gloves. Wearing safety
leg guards is recommended.
Always wear foot protection. Do not go
S
barefoot or wear sandals. Stay clear of
spinning line.
Secure hair above shoulder length.Se-
S
cure or remove loose clothing or clothing
with loosely hanging ties, straps, tassels,
etc. They can be caught in moving parts.
Being fully covered also helps protect you
S
from debris and pieces of toxic plants
thrown by spinning line.
Stay Alert. Do not operate this unit when
S
you are tired, ill, upset, or under the influence of alcohol, drugs, or medication.
Wear hearing protection.
S
Never start or run inside a closed room or
S
building. Breathing exhaust fumes can kill.
Keep handles free of oil and fuel.
S
UNIT / MAINTENANCE SAFETY
Disconnect the spark plug before perform-
S
ing maintenance (except carburetor adjustments).
Look for and replace damaged or loose
S
parts before each use. Look for and repair
fuel leaks before use. Keep in good working condition.
Replace trimmer head parts that are
S
chipped, cracked, broken, or damaged in
any other way before using the unit.
Maintain unit according to recommended
S
procedures. Keep cutting line at proper
length.
Use only 0.080” (2 mm) diameter Poulan/
S
Weed Eater!brand line. Never use wire,
rope, string, etc.
Install required shield properly before using
S
the unit. Use only specified trimmer head;
make sure it is properly installed and securely fastened.
Make sure unit is assembled correctly as
S
shown in this manual.Make carburetor adjustments with lower end supported to prevent line from contacting any object.
Keep others away when making carburetor
S
adjustments.
Use only recommended Weed Eater!ac-
S
cessories and replacement parts.
Have all maintenance and service not ex-
S
plained in this manual performed by an authorized service dealer.
FUEL SAFETY
Mix and pour fuel outdoors.
S
Keep away from sparks or flames.
S
Use a container approved for fuel.
S
Do not smoke or allow smoking near fuel or
S
the unit.
Avoid spilling fuel or oil. Wipe up all fuel
S
spills.
Move at least 10 feet (3 meters) away from
S
fueling site before starting engine.
Stop engine and allow to cool before re-
S
moving fuel cap.
Always store gasoline in a container ap-
S
proved for flammable liquids.
2
CUTTING SAFETY
WARNING:
each use. Remove objects (rocks, broken
glass, nails, wire, etc.) which can be thrown
by or become entangled in line. Hard objects
can damage trimmer head and be thrown
causing serious injury.
Use only for trimming, mowing, edging and
S
sweeping. Do not use for pruning or hedge
trimming.
Keep firm footing and balance. Do not over-
S
reach.
Keep all parts of your body away from spin-
S
ning line and muffler. Keep engine below
waist level. A hot muffler can cause serious
burns.
Cutting with the line on left side of the shield
S
will throw debris away from the operator.
Use only in daylight or good artificial light.
S
Inspect the area before
TRANSPORTING AND STORAGE
Allow the engine to cool; secure unit before
S
storing or transporting in vehicle.
Empty the fuel tank before storing or trans-
S
porting the unit. Use up fuel left in the carburetor by starting the engine and letting it
run until it stops.
Store unit and fuel in an area where fuel va-
S
pors cannot reach sparks or open flames
from water heaters, electric motors or
switches, furnaces, etc.
Store unit so line limiter blade cannot acci-
S
dentally cause injury. Unit can be hung by
the tube.
Store the unit out of the reach of children.
S
SAFETY NOTICE:
through prolonged use of gasoline powered
hand tools could cause blood vessel or nerve
damage in the fingers, hands, and joints of
people prone to circulation disorders or abnormal swellings. Prolonged use in cold weather
has been linked to blood vessel damage in
otherwise healthy people. If symptoms occur
such as numbness, pain, loss of strength,
change in skin color or texture, or loss of feeling
in the fingers, hands, or joints, discontinue the
use of this tool and seek medical attention. An
anti-vibration system does not guarantee the
avoidance of these problems. Users who operate power tools on a continual and regular basis
must monitor closely their physical condition
and the condition of this tool.
SPECIAL NOTICE:
with a temperature limiting muffler and spark arresting screen which meets the requirements of
California Codes 4442 and 4443. All U.S. forest
land and the states of California, Idaho, Maine,
Minnesota, New Jersey, Oregon, and Washington require by law that many internal combustion engines be equipped with a spark arresting
screen. If you operate in a locale where such
regulations exist, you are legally responsible for
maintaining the operating condition of these
parts. Failure to do so is a violation of the law.
For normal homeowner use, the muffler and
spark arresting screen will not require any ser-
Exposure to vibrations
This unit is equipped
vice. After 50 hours of use, we recommend that
your muffler be serviced or replaced by your authorized service dealer.
ASSEMBLY
WARNING:
properly assembled and all fasteners are secure.
ATTACHING THE HANDLE
Groove
Assemble handle to the unit as shown;
S
make sure bottom of handle is seated in the
groove in the trigger housing.
Wing nut must be assembled on the
NOTE:
side of the unit opposite the operator’s position.
Pivot handle to a comfortable position.
S
Tighten handle securely.
ATTACHING THE SHIELD
WARNING:
erly installed. The shield provides partial
protection from the risk of thrown objects to
the operator and others and is equipped with
a line limiter blade which cuts excess line to
the proper length. The line limiter blade (on
underside of shield) is sharp and can cut you.
Remove wing nut from shield.
S
Insert bracket into slot as shown.
S
Pivot shield until bolt passes through hole
S
in bracket.
Securely tighten wing nut onto bolt.
S
Shield
Line Limiter Blade
Make sure your unit is
The shield must be prop-
Slot
Bracket
Wing
Nut
FUEL YOUR UNIT
WARNING:
when refueling.
This engine is certified to operate on un-
leaded gasoline. Gasoline must be mixed
with a good quality synthetic 2--cycle air-cooled engine oil designed to be mixed at a
ratio of 40:1. Poulan/Weed Eater brand syn-
3
Remove fuel cap slowly
thetic oil is recommended. (A 40:1 ratio is obtained by mixing 3.2 ounces of oil with 1 gallon
of unleaded gasoline). When mixing fuel follow the instructions printed on the container.
Always read and follow the safety rules under
FUEL SAFETY.
OPERATING POSITION
ALWAYS WEAR:
Eye
Protection
STARTING
HOW TO STOP YOUR UNIT
To stop engine, move ON/OFF switch to the
OFF position.
HOW TO START YOUR UNIT
Starting Position
Choke lever
Trigger
Primer Bulb
WARNING:
turn while starting the engine. A hot muffler
can cause serious burns.
The trimmer head will
Muffler
STARTING A COLD ENGINE (or a
warm engine after running out of
fuel)
Set unit on a flat surface.
S
Move ON/OFF switch to the ON position.
S
Slowly press the primer bulb 6 times.
S
Move choke lever to FULL CHOKE posi-
S
tion.
Squeeze the throttle trigger fully and hold
S
through
all remaining steps
Pull starter rope handle sharply 6 times.
S
Move choke lever to HALF CHOKE posi-
S
tion.
Pull starter rope handle no more than 6
S
pulls, until engine runs.
Allow engine to run 10 seconds, then move
S
choke lever to OFF CHOKE position.
.
STARTING A WARM ENGINE
Move ON/OFF switch to the ON position.
S
Move choke lever to OFF CHOKE position.
S
Pull starter rope handle until engine runs.
S
If engine does not start in 5 pulls, follow
S
instructions in STARTING A COLD ENGINE.
USING YOUR UNIT
It is recommended that the engine not be
operated for longer than 1 minute at full
throttle.
Long Pants
Heavy Shoes
Cut from your right to your left.
ADVANCING THE CUTTING LINE
Advance line by tapping the bottom of the cutting head lightly on the ground while engine is
running at full speed. A metal blade attached
to the shield will cut the line to the proper
length.
TWIST--N--EDGE
Pull the tab toward the engine.
S
Twist the tube to the edging position;
S
release the tab.
Tab
REPLACING THE LINE
Remove spool by firmly pulling on tap but-
S
ton.
Clean entire surface of hub and spool.
S
Replace with a pre-wound spool, or cut a
S
length of 20 feet of 0.080” (2 mm) diameter
Weed Eaterrbrand line. Never use wire,
rope, string, etc., which can break off and
become a dangerous missile.
Insert one end of the line about 1/2 inch (1
S
cm) into the small hole on the inside of
spool.
Small
Hole
Line in Notch
Hub
Wind the line evenly and tightly onto the
S
spool. Wind in the direction of the arrow
found on the spool.
Push the line into the notch, leaving 3 to 5
S
inches (7 -- 12 cm) unwound.
4
Spool
Line exit hole
Insert the line into the the exit hole in the hub
e
S
as shown in the illustration.
Align the notch with the line exit hole.
S
Push spool into hub until it snaps into place.
S
Pull the line extending outside of the hub to
S
release it from the notch.
SERVICE
WARNING:
uct contains chemicals known to the State of
California to cause cancer.
WARNING:
and after use. Do not touch the muffler or allow combustible material such as dry grass or
fuel to do so.
The muffler on this prod-
Muffler is very hot during
We recommend all service and adjustments
not listed in this manual be performed by an
authorized service dealer.
CARBURETOR ADJUSTMENTS
Your carburetor is equipped with limiter caps.
Carburetor adjustment is a complicated task.
We recommend that you take your unit to an
authorized service dealer. Damage will occur
if you turn the needles beyond the limiter
stops.
IGNITION TIMING
The ignition timing is fixed, non-adjustable.
SPARK PLUG
Replace the spark plug yearly using a Champion RCJ--7Y plug. Spark plug gap is 0.025”.
TROUBLESHOOTING TABLE
WARNING:
recommended remedies below other than remedies that require operation of the unit.
Always stop unit and disconnect spark plug before performing any of th
TROUBLE CAUSE REMEDY
Engine will not
start.
Engine will not
idle properly.
Engine will not
accelerate,
lacks power,
or dies under
a load.
Engine
smokes
excessively.
Line does not
advance or
breaks while
cutting.
Line welds
onto spool.
Line pulls
back into
head.
ON/OFF switch in OFF
S
position.
Engine flooded.
S
Fuel tank empty.
S
Spark plug not firing.
S
Fuel not reaching carburetor.
S
Carburetor requires adjustment.
S
Carburetor requires adjustment.
S
Throttle trigger screw too
S
tight.
Air filter dirty.
S
Spark plug fouled.
S
Carburetor requires adjustment.
S
Fuel mixture incorrect.
S
Air filter dirty.
S
Carburetor requires adjustment.
S
Line improperly routed in head.
S
Line improperly wound on
S
spool.
Line size incorrect.
S
Line size incorrect.
S
Incorrect spool.
S
Line is being crowded against
S
material being cut.
Too little line outside of head.
S
Line size incorrect.
S
Move ON/OFF switch to ON.
S
See “Starting.”
S
Fill tank with correct fuel mixture.
S
Install new spark plug.
S
Check for dirty fuel filter; replace.
S
Check for kinked or split fuel line;
repair or replace.
See “Carburetor Adjustments.”
S
See “Carburetor Adjustments.”
S
Loosen screw.
S
Clean or replace air filter.
S
Clean or replace spark plug; re-gap.
S
See “Carburetor Adjustments.”
S
Empty fuel tank and refill with
S
correct fuel mixture.
Clean or replace air filter.
S
See “Carburetor Adjustments.”
S
Check line routing.
S
Rewind line tightly and evenly.
S
Use only 0.080” (2 mm) dia. line.
S
Use only 0.080” (2 mm) dia. line.
S
Replace with correct spool.
S
Cut with tip of line fully extended.
S
Remove spool and pull 4 inches
S
(10 cm) of line outside of head.
Use only 0.080” (2 mm) dia. line.
S
5
NEED ASSISTANCE?
Need Assistance?
Call 1-800-554-6723.
Need Service Parts?
Contact your dealer .
LIMITED WARRANTY
ELECTROLUX HOME PRODUCTS, INC.,
warrants to the original purchaser that each
Weed Eater
new
tachment is free from defects in material and
workmanship and agrees to repair or replace
under this warranty any defective gasoline
product or attachment as follows from the
original date of purchase.
2 YEARS--
household purposes.
90 DA YS --
commercial, professional, or income producing purposes.
30 DAYS --
purposes.
This warranty is not transferable and does not
cover damage or liability caused by improper
handling, improper maintenance, or the use
of accessories and/or attachments not specifically recommended by
HOME PRODUCTS, INC.,
tionally, this warranty does not cover tuneups, spark plugs, filters, starter ropes, starter
springs, cutting line, or rotating head parts
that will wear and require replacement with
reasonable use during the warranty period.
This warranty does not cover predelivery setup or normal adjustments explained in the instruction manual.
THIS WARRANTY GIVES YOU SPECIFIC
LEGAL RIGHTS, AND YOU MAY HAVE
OTHER RIGHTS WHICH VARY FROM
STATE TO STATE.
NO CLAIMS FOR CONSEQUENTIAL OR
OTHER DAMAGES WILL BE ALLOWED,
AND THERE ARE NO OTHER EXPRESS
WARRANTIES EXCEPT THOSE EXPRESSLY STIPULATED HEREIN.
SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS OR THE EXCLUSION OR
LIMITATIONS OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE
LIMITATIONS OR EXCLUSION MAY NOT
APPLY TO YOU.
The policy of
UCTS, INC.,
products. Therefore,
PRODUCTS, INC.,
change, modify, or discontinue models, designs, specifications, and accessories of all
products at any time without notice or obligation to any purchaser.
brand gasoline tool or at-
Parts and Labor, when used for
Parts and Labor, when used for
Parts and Labor, if used for rental
ELECTROLUX
for this tool. Addi-
ELECTROLUX HOME PROD-
is to continuously improve its
ELECTROLUX HOME
reserves the right to
U.S. EPA/CALIFORNIA
EMISSION CONTROL
WARRANTY STATEMENT
YOUR WARRANTY RIGHTS AND OBLIGATIONS:
Agency/California Air Resources Board and
POULAN/W EED EATER, DIVISION OF WCI
OUTDOOR PRODUCTS are pleased to ex-
plain the emissions control system warranty on
your year 2000--2003 small off--road engine. In
California, all new small off--road engines must
be designed, built, and equipped to meet the
State’s stringent anti --smog standards. POU-
LAN/WEED EATER must warrant the emission
control system on your small off--road engine for
the periods of time listed below provided there
has been no abuse, neglect, or improper maintenance of your small off--road engine engine.
Your emission control system includes parts
such as the carburetor and the ignition system.
Where a warrantable condition exists, POU-
LAN/WEED EATER will repair your small off--
road engine engine at no cost to you. Expenses
covered under warranty include diagnosis,
parts and labor.
RANTY COVERAGE:
part on your engine (as listed under Emissions
Control Warranty Parts List) is defective or a defect in the materials or workmanship of the engine causes the failure of such an emission related part, the part will be repaired or replaced
by POULAN/WEED EATER.
WARRANTY RESPONSIBILITIES:
small off--road engine engine owner , you are responsible for the performance of the required
maintenance listed in your instruction manual.
POULAN/W EED EATER recommends that
you retain all receipts covering maintenance on
your small off--road engine, but POULAN/
WEED EATER cannot deny warr anty solely for
the lack of receipts or for your failure to ensure
the performance of all scheduled maintenance.
As the small off--road engine engine owner, you
should be aware that POULAN/WEED EATER
may deny you warr anty coverage if your small
off--road engine engine or a part of it has failed
due to abuse, neglect, improper maintenance,
unapproved modifications, or the use of parts
not made or approved by the original equipment
manufacturer. Y ou are responsible for presenting your small off--road engine to a POULAN/
WEED EATER authorized repair center as
soon as a problem exists. Warranty repairs
should be completed in a reasonable amount of
time, not to exceed 30 days. If you have any
questions regarding your warrantyrights and responsibilities, you should contact your nearest
authorized service center or call POULAN/
WEED EATER at 1--800--554--6723.
RANTY COMMENCEMENT DATE:
ranty period begins on the date the small
off--road engine is purchased.
COVERAGE:
od of two years from the initial date of purchase.
6
The U.S. Environmental Protection
MANUFACTURER’S WAR-
If any emissions related
OWNER’S
As the
WAR-
The war-
This warranty shall be for a peri-
LENGTH OF
WHAT IS COVERED: REPAIR OR REPLACEMENT OF PARTS.
ment of any warr anted part will be performed at
no charge to the owner at an approved POU-
LAN/WEED EATER servicing center. If you
have any questions regarding your warranty
rights and responsibilities, you should contact
your nearest authorized service center or call
POULAN/W EED EATER at 1--800--554--6723
WARRANTY PERIOD:
which is not scheduled for replacement as required maintenance, or which is scheduled only
for regular inspection to the effect of “repair or
replace as necessary” shall be warranted for 2
years. Any warranted part which is scheduled
for replacement as required maintenance shall
be warranted for the period of time up to the first
scheduled replacement point for that part.
DIAGNOSIS:
for diagnostic labor which leads to the determination that a warranted part is defective if the
diagnostic work is performed at an approved
POULAN/W EED EATER servicing center.
CONSEQUENTIAL DAMAGES:
WEED EATER may be liable for damages to
other engine components caused by the failure
of a warranted part still under warranty.
IS NOT COVERED
abuse, neglect, or improper maintenance are
The owner shall not be charged
Repair or replace-
Any warranted part
POULAN/
: All failures caused by
WHA T
not covered.
PARTS:
can be grounds for disallowing a warranty claim.
POULAN/W EED EATER is not liable to cover
failures of warranted parts caused by the use of
add--on or modified parts.
CLAIM:
your warranty rights and responsibilities, you
should contact your nearest authorized service
center or call POULAN/WEED EATER at
1--800--554--6723.
RANTY SERVICE:
pairs shall be provided at all POULAN/WEED
EATER service centers. call: 1--800--554--6723
MAINTENANCE, REPLACEMENT AND REPA IR OF EMISSION RELATED PA RTS
POULAN/W EED EATER approved replace-
ment part used in the performance of any warranty maintenance or repair on emission related
parts will be provided without charge to the owner if the part is under warranty.
CONTROL WARRANTY PARTS LIST :
buretor, Ignition System: Spark Plug (covered
up to maintenance schedule), Ignition Module,
Muffler including catalyst.
STATEMENT:
performance of all required maintenance as defined in the instruction manual.
ADD--ON OR MODIFIED
The use of add--on or modified parts
If you have any questions regarding
WHERE TO GET WAR-
Warranty services or re-
The owner is responsible for the
This engine is certified to be emissions compliant for the following use:
Moderate (50 hours)
Intermediate (125 hours)
Extended (300 hours)
HOW TO FILE A
:Any
EMISSION
Car-
MAINTENANCE
7
Loading...