Weber Ranch Kettle Assembly Guide
RANCH® KETTLE ADDENDUM SHEET
Please note the following changes to your assembly manual.
ASSEMBLY
INSTALL BOWL ASSEMBLY
6
You will need: Bowl assembly, four 5/16-18 x 7/8 inch bolts, four 5/16 inch steel
washers, four 5/8 inch aluminum washers, four 5/16-18 hex nuts, four 5/16 inch
lock washers, 1/2 inch open-end or an adjustable wrench and pliers.
Set bowl in frame. Place a steel washer (1) on bolt (2) and insert through frame
assembly and bowl. Place aluminum washer (3), lock washer (4) and hex nut (5)
on bolt and tighten. Install the other bolts in locations shown.
INSTALL LID TABS
7
You will need: Two lid tabs, two 5/16-18 x 7/8 inch bolts, two 5/8 inch
aluminum washers, two 5/16-18 hex nuts, two 5/16 inch lock washers, 1/2 inch
open-end or an adjustable wrench and pliers.
Insert bolt (1) through lid tab (2), frame assembly and bowl on outside of caster
legs. Place aluminum washer (3), lock washer (4), then hex nut (5) on bolt and
tighten.
PARTS
Wire lid holder assembly
8
(5)
(4)
(3)
(1)
(2)
(5)
(4)
(3)
(2)
(1)
9
ASSEMBLY
9
INSTALL WIRE LID HOLDER ASSEMBLY
8
You will need: Wire lid holder assembly and a 1/2 inch open-end or
an adjustable wrench.
Place lid bushing (5), 5/16 -18 hex nut (4) and 5/16” steel washer (6)
onto each end of wire lid holder.
Note - Bushings (5) should roll freely on wire lid holder.
Insert ends of wire lid holder through frame assembly and bowl on outside of
wheel legs. Place 5/8 inch aluminum washer (3), 5/16 inch lock washer (2)
then 5/16-18 hex nut (1) on each end of the wire lid holder and tighten.
(4)
(5)
(6)
WARRANTY
Weber-Stephen Products Co., (Weber) hereby warrants to the ORIGINAL PURCHASER of this
Weber® One-Touch® Silver,
One-Touch® Gold, One-Touch® Platinum, Smokey Mountain Cooker™, and Ranch® grills, that it will
be free from defects in material and workmanship from the date of purchase as follows:
Cooking / Charcoal grates 2 years
Stainless Steel One-Touch™ Cleaning System (One-Touch® Platinum) 10 years
Bowl and lid against rust / burn-through 10 years
Nylon handles 10 years
Thermoplastic/Thermoset Parts(One-Touch® Platinum) 10 years
excluding fading
When assembled and operated in accordance with the printed instructions accompanying it. Weber may require
reasonable proof of your date of purchase. THEREFORE, YOU SHOULD RETAIN YOUR SALES SLIP OR
INVOICE AND RETURN THE WEBER LIMITED WARRANTY REGISTRATION CARD IMMEDIATELY.
This Limited Warranty shall be limited to the repair or replacement of parts which prove defective under normal
use and service and which on examination shall indicate to Weber’s satisfaction they are defective. If Weber
confirms the defect and approves the claim, Weber will elect to repair or replace such parts without charge. If
you are required to return defective parts, transportation charges must be prepaid. Weber will return parts to the
purchaser, carriage or postage prepaid.
This Limited Warranty does not cover any failures or operating difficulties due to accident, abuse, misuse,
alteration, misapplication, vandalism,
improper installation or improper maintenance or service, or failure to perform normal and routine maintenance.
Deterioration or damage due to severe weather conditions such as hail, hurricanes, earthquakes or tornadoes,
discoloration due to exposure to chemicals, either directly or in the atmosphere, is not covered by this Limited
Warranty.
There are no other express warranties except as set forth herein, and any applicable implied warranties of
merchantability and fitness are limited in duration to the period of coverage of this express written Limited
Warranty. Some regions do not allow limitation on how long an implied warranty lasts, so this limitation may not
apply to you.
Weber is not liable for any special, indirect or consequential damages. Some regions do not allow the exclusion
or limitation of incidental or consequential damages, so this limitation or exclusion may not apply to you.
Weber does not authorise any person or company to assume for it any other obligation or liability in connection
with the sale, installation, use, removal, return or replacement of its equipment; and no such representations are
binding on Weber.
All remaining parts 2 years
11
(1)
(2)
(3)
HARDWARE - STEP 8
Two 5/8 inch aluminum
washers (actual size)
Two Lid Bushings
Four 5/16 -18 hex nuts
9
Two 5/16” lock washers
Two 5/16” Steel washers
90648 010908
EXPLODED VIEW / EXPLODED VIEW LIST
12
All items are single quantities unless otherwise specified. Parts can be ordered from
Weber-Stephen Products Co. by phone or mail.
Note - Do not return parts to Weber-Stephen Products Co. without first contacting the
Customer Service Center by phone or mail. Returning the part may not be necessary.
1. #8-16 x 5/8 inch screw
2. Nylon lid handle (top)
3. Nylon lid handle (bottom)
4. 1/4-20 x 5/8 inch screws (4)
5. 1/4 inch flat washers (5)
6. Lid damper
7. 1/4-20 acorn nuts (4)
8. Lid
9. Hinged cooking grate
10. Charcoal grate
11. Wire lid support
12. 5/16 inch steel washers (6)
13. 5/16-18 hex nuts (8)
14. Bushings (2)
15. 5/8 inch aluminum washers (16)
16. 5/16 inch lock washers (8)
17. Bowl
18. Bowl dampers (3)
19. 1/4-20 hex nuts (6)
20. Nylon washers (12)
21. 1/4-20 x 1 3/4 inch bolts (5)
22. Frame handle
23. Tool holders (3)
24. Aluminum tubing plugs (4)
25. 5/16-18 x 7/8 inch bolts (6)
26. Ash catcher
27. Top frame
28. 1/4-20 x 3 inch bolt
29. Lid tabs (2)
30. Plastic tubing plug
31. Tuck-Away support bracket
32. Tuck-Away frame support
33. Bottom frame
34. Caster inserts (2)
35. Casters (2)
36. Axle
37. Wheels (2)
38. Wheel hubcaps (2)
1
2
3
4
5
6
7
8
9
10
17
11
12
13
14
15
16
13
7
5
18
4
19
20
21
22
23
24
25
12
15
16
13
26
27
28
20
Printed in U.S.A.
19
13
16
15
29
25
30
19
20
31
20
21
32
33
34
35
36
37
38
Loading...