Wayne Fueling Systems WAYNETRACII correction for installation manual section two
Section 2
Vista EasyPAY Kit Installation
2.1 Introduction
The information in this chapter explains how to install the EasyPAY retrofit kit (PN 887122-001).
Note: It is necessary to identify Side 1 and Side 2 of the dispenser in order to carry out the instructions
that follow. Note that the dispenser ID plate is located on the lower left corner of the chassis frame on
Side 1. See Figure 2-16 for illustration.
2.2 Removing Dispenser Power
Before you begin installing the retrofit kit, perform the following steps to protect the kit assemblies from
damage.
1. Close station to fuel purchases.
2. Disconnect the power from dispensers at the power panel. Post a warning sign at the power panel
stating that the equipment is being serviced.
2-1
July 2000 Part No. 920472 Rev. C
Section 2: Vista EasyPAY Kit Installation
1
3
Tilt the ad panel out and down toward you.
Lift For Receipt
2.3 Removing the Bezels
Complete the following steps to remove the bezels from the dispenser.
1. Remove and save any temporary advertisement or instructional attachments from the bezel face.
2. Place an anti-static wrist strap (PN 916962 or equivalent) on your wrist and attach the other end of
the wrist strap to an earth grounding point.
3. Disengage the advertisement (ad) panels. Unsnap the ad panel by pulling forward firmly on the top
edge of the panel. Refer to Figure 2-1.
Wayne
DJR-FH/CD-1302A
1
Lift For Receipt
2
WAYNE
1
1/4 Turn Phillips Head Screws
2
Ad Panel
3
Blank Panel
Figure 2-1 Removing the Ad Panel
4. If necessary, unlock the function switch door.
5. Turn the wing fasteners on the left and right side of bezel counter clockwise. Refer to Figure 2-2.
2-2
Part No. 920472 Rev. C July 2000
Section 2: Vista EasyPAY Kit Installation
34432
PTS Bar
Ad Panel Fasteners
Function Switch Door Lock
JP1
DJR-FH/CD-1304A
Graphic Display Adapter Board
Lift For Receipt
DJR-CD-1303A
2
1
1
Ad Panel (lowered)
2
Wing Fasteners
WAYNE
3
Area
Figure 2-2 Wing Fasteners on Bezel
6. Rest the lower edge of the bezel on the dispenser and disconnect the following cables from the back
of the bezel.
a. If the bezel is equipped with a graphic display, disconnect the graphic display heater cable (PN
882827-001) plugged in the 2-conductor black connector that routes on the right side of the
graphic display. See Figure 2-3.
Rear View of CPM Bezel
J3
J5
(Part No. 882440-xxx)
DES Keypad
4-Pin DES Keypad Cable
Vista Annunciator Interface
Board (Part No. 883074-xx)
Figure 2-3 Disconnecting Cables on Back of Graphic Display Bezel
b. Disconnect the cable assembly (PN 881524-001) installed in J5 on the annunciator interface
board. Refer to Figure 2-3 and Figure 2-4 for the following steps.
c. If the bezel is equipped with a Push-to-Start (PTS) bar, disconnect the cable assembly (PN
881692-01 or 881693-01) plugged in the 13-pin connector on the back of the bezel.
d. If the bezel is equipped with a CPM and a DES keypad, disconnect the cable assembly (PN
880963-02) plugged in the 4-pin connector on the DES keypad cable.
July 2000 Part No. 920472 Rev. C
e. If the bezel is equipped with KDC and a DES keypad is present, disconnect the cable assembly
(PN 880963-01) plugged in the 4-pin DES keypad cable.
2-3
Section 2: Vista EasyPAY Kit Installation
DJR-FH/CD-1107A
Rear View of KDC Bezel
Rear View of CPM Bezel
Captive Screw
Display Board
Display Bracket
J4 on Annunciator
(Part No. 880869-xx)
Annunciator Interface Board
f. Repeat steps 3 through 6 to remove the bezel on the other side of the dispenser.
2.4 Lowering the DEMs
Perform the following steps to lower the DEM(s) (Display Electronic Modules) to the service position.
1. Use a slotted screwdriver to loosen two ¼ turn screws located at the top of the DEM. Refer to
Figure 2-5.
2. Lower the DEM to the service position.
3. Repeat steps 1 and 2 for the DEM on the other side of the dispenser.
J4
Rain Catcher
J10
J9J3
J1
J2
J2
J5
(5 Places)
J4
J5
J1
Mounting Screw
(4 Places)
Interface Board
Display Bracket
Mounting Screw
(4 Places)
Display Board
(Part No. 881182-xx
or 883072-xx)
2-4
Part No. 920472 Rev. C July 2000
Figure 2-4 Disconnecting Cables on Bezel Back
DEM 1/4 Screws (2 Places)
DJR-FH/CD-1321A
Section 2: Vista EasyPAY Kit Installation
Dispenser
Side View
Side 1
Dispenser
Front View
DEM
Service
Position
Figure 2-5 Lowering the DEM into the Service Position
2.5 Installing the Authorization Light Assembly (PN887124)
Complete the following steps to remove the blank panel from the bezel and install the authorization light
assembly (PN 887124-001) in its place. Refer to Figure 2-6.
1. Locate the side 1 bezel removed earlier in paragraph 2.3.
2. Use a ¼ inch nut driver to loosen and remove 3 hex head screws securing the blank panel to the
back of the bezel. (See the following figure.) Set the blank panel aside. Retain the hardware for
reinstallation later.
Note: Examine bezel opening to determine that all material from the old gasket has been
removed.
2-5
July 2000 Part No. 920472 Rev. C
Loading...