Keyed-in-Handle Autolatch ECR Lock
Installation Instructions
and Owner’s Manual
Wayne-Dalton Corp.
P.O. Box 67 Mt. Hope, OH 44660
(888) 827-3667
www.wayne-dalton.com
All Residential Door Models: 8000/9000 Series & Wood Doors
PHILLIPS HEAD MACHINE SCREWS
(2) 1” (9200) #306564
(2) 1-1/4” (9600/8300 & WOOD)#306565
(2) 1-1/2” (9900) #306566
(2) 1-3/4” (8000/PR9000/8500) #306567
OUTSIDE HANDLE #255543
LOCK BACKUP PLATE (8300/8500 & WOOD)
#128564
(2) AUTOLATCH FLIPPERS
(2)STRIKER #100287 PLATES #299008
LOCK CABLE #307894
(6) 1/4-20 X 11/16” SELF DRILLING SCREWS #300723
(2) FOAM TAPE |
(6) 1/4” -20 |
(9200/9600/9900) |
FLANGED HEX NUTS |
3/4” X 2-1/2” |
#100279 |
#306653 |
|
UNIVERSAL
LOCK STILE (9200/9600 & 9900) #261964
|
(6) 1/4-20 X 9/16” |
|
INSIDE DOOR HANDLE |
TRACK BOLTS |
|
#200527 |
||
#307893 |
||
|
(2) #8 - 32 X 3/4”
PHILLIPS HEAD SELF TAPPING SCREWS #100278
1/4-14 X 1” LAG SCREWS
OR (WOOD DOORS ONLY) #107584
Required Tools
(1)Electric Drill
(1)1/8” Drill Bit
(1)3/4” Dia. Hole Saw
(1)7/16” 6 Point Nut Driver
(1)7/16” Wrench Or Socket
(1)Pliers/Wire Cutter
(1)Phillips Screw Driver
(1)Standard Screw Driver
(1)Center Punch
Important Notice!
REFER TO THE DOOR MODEL INSTALLATION INSTRUCTIONS MANUAL FOR
IMPORTANT SAFETY NOTICES.
© Copyright 2003 Wayne-Dalton Corp. |
Part No: 307895 |
New 6/10/03 |
Step 1: Installing the ECR Lock
CAUTION DO NOT DRILL LOCK
SECTION OR INSTALL LOCK ON DOORS WITH OPENERS. THE DOOR AND/ OR OPENER MAY BE DAMAGED IF THE OPENER IS USED WHILE THE DOOR IS LOCKED.
NOTE: Common practice for doors with the odd number of raised panels is to mount the lock towards the right side of the section when looking out.
IMPORTANT: Remove all burrs from the drilled holes before installing the lock to the section.
8000/8100/8200/PR9000 & PR9050 Series doors (see Fig.1), place the lock section face down on (2) padded sawhorses for a single car door or (3) padded sawhorses for a double car door. Locate the (3) hole pattern in the center stile of the lock section. Use the (3) holes as a template to drill (3) 1/8” diameter holes through the section. Flip the section over, face up. With the section face up, enlarge all (3) holes to 3/4” diameter, pay close attention not to drill complete through section into center stile.
NOTE: Do not drill through or enlarge holes in the center stile.
8300/8500 Series & Wood doors (see Fig.2), place the lock section face up on (2) padded sawhorses for a single car door or (3) padded sawhorses for a double car door. Locate the middle of the center stile, measure the distance from the end of the section to the middle of the center stile. Turn the section face down, transfer the measurement and mark a light vertical line, then mark a horizontal line at half the section height. Align the 7/16” diameter hole of the lock backup plate at the intersection point of the horizontal and vertical marks, use the lock backup plate as a template to mark the (3) holes, remove the lock backup plate and drill (3) 3/4” diameter holes through the section.
CENTER STILE
(3)PRE-PUNCHED 
HOLES
(3) 3/4” DIA.
HOLES FACE UP
FACE DOWN
VERTICAL
MARK
HORIZONTAL MARK
7/16” DIA. HOLE
(3) 3/4”DIA.
HOLES
LOCK BACKUP |
FACE DOWN |
|
PLATE |
||
|
VERTICAL
MARK
(3) 3/4”DIA. 
HOLES
LOCK STILE |
FACE DOWN |
9000 Series doors (see Fig.3), place the lock section face up on (2) padded sawhorses for a single car door or
(3) padded sawhorses for a double car door. Locate the
middle of the center stile, measure the distance from the end of the section to the middle of the center stile. Turn the section face down, transfer the measurement and mark a light vertical line. Align the center of the lock stile with vertical mark, use the lock stile as a template to mark the (3) holes, remove the lock stile and drill (3) 3/4” diameter
holes through the section. |
2 |
Loading...