For Residential and Commercial Applications
ES-WP-PACrimpManifolds
Job Name
Job Location
Engineer
Approval
LEAD FREE
–––––––––––––––––––––––––––––––––––––––––––
–––––––––––––––––––––––––––––––––––––––––
–––––––––––––––––––––––––––––––––––––––––––––
–––––––––––––––––––––––––––––––––––––––––––––
*
Poly-Alloy CrimpRing
Manifolds
Poly-Alloy CrimpRing™ Manifolds are used to create multiple
connections for circuit and branch applications using a single
fitting with WaterPEX
distribution or as a branch distribution fitting for a remote fixture
group.
Specifications
System shall be plumbed using Watts WaterPEX® cross-linked
polyethylene pipe. All joints shall be made using Watts brass
CrimpRing
the Watts copper CrimpRing
crimping methods as outlined in the Watts WaterPEX
Installation Guidelines.
™
and/or poly-alloy CrimpRing™ fittings using either
Installation Note
CrimpRing™ Manifold must be installed in accordance with all
Watts WaterPEX
provided in WaterPEX
®
pipe. They can be used for master water
™
or stainless steel CinchClamp™
®
installation procedures, including information
®
installation manual and guidelines.
®
Contractor
Approval
Contractor’s P.O. No.
Representative
™
––––––––––––––––––––––––––––––––––––––––––––
–––––––––––––––––––––––––––––––––––––––––––––
––––––––––––––––––––––––––––––––––
––––––––––––––––––––––––––––––––––––––––
WPPM-1212-M2AF
WPPM-1212-M3BF
WPPM-12-M4AB
Approvals
WPPM-12-M3BB
• Manufactured in accordance with American Society
for Testing and Materials (ASTM) F-877 and F-2159
• Listed by the National Sanitation Foundation to NSF
Standards 14 and 61 for use in potable water systems
• Listed by IAPMO to be in compliance with the Uniform
Plumbing Code
• Labeled B137.5 which indicates that it is compliant
to the CSA Standard B137.5
• Manufactured from Acudel
* The wetted surface of this product contacted by consumable
water contains less than one quarter of one percent (0.25%) of
lead by weight.
** Note: Watts WaterPEX CinchClamp™ should not be used
with wrot copper PEX fittings.
Acudel® is a registered trademark of Solvay Advanced Polymers.
Watts product specifications in U.S. customary units and metric are approximate and are provided for reference only. For precise measurements,
please contact Watts Technical Service. Watts reserves the right to change or modify product design, construction, specifications, or materials without prior notice and without incurring any obligation to make such changes and modifications on Watts products previously or subsequently sold.
®
engineered thermoplastic resin.
Cau t i o n :
The polyphenylsulfone material used in the Poly-Alloy
CrimpRing manifolds can be compromised by exposure to
volatile organic compounds (VOC’s) and caustic chemicals
which would include exposure to the following products: Pipe
Dopes and thread sealants, insect sprays, lubricants, cleaners,
paints, bleaches, acids, solder fluxes, plastic piping primers
and cements, oxidizing agents, alkaline solutions, thinners,
fuels, oil based caulks, hydrocarbons, spray foam insulations.
CAU T I O N !
If connections must be made in temperatures below 30°F,
caution must be taken to allow the WaterPEX to form a proper
seal against the barb in order to avoid subsequent water damage. Apply the connection slowly to ensure the PEX material
conforms to the barb.
Dimensions – Weights
Model Inlet oUtlet PoRtS PKG WeIGHt
in mm. in
mm.
.
in mm
Qty/Configuration lbs. kgs.
Flow Through - Side Ports
WPPM-1212-M2AF
WPPM-1212-M3AF
WPPM-1212-M4AF
3
⁄4 20
3
⁄4 20
3
⁄4 20
WPPM-1612-M4AF 1 25
WPPM-1612-M6AF 1 25
WPPM-1616-M6AF 1 25 1 25
3
⁄4 20
3
⁄4 20
3
⁄4 20
3
⁄4 20
3
⁄4 20
Flow Through - Offset Ports
WPPM-1212-M3BF
WPPM-1212-M4BF
3
⁄4 20
3
⁄4 20
3
⁄4 20
3
⁄4 20
Closed End - Side Ports
WPPM-12-M4AB
WPPM-16-M6AB 1 25 Closed Closed
3
⁄4 20 Closed Closed
Closed End - Offset Ports
WPPM-12-M3BB
WPPM-12-M4BB
3
⁄4 20 Closed Closed
3
⁄4 20 Closed Closed
1
⁄2 15 2/One Side .04 .018
1
⁄2 15 3/One Side .05 .022
1
⁄2 15 4/One Side .06 .027
1
⁄2 15 4/One Side .1 .045
1
⁄2 15 6/One Side .14 .063
1
⁄2 15 6/One Side .15 .068
1
⁄2 15 3/Offset .04 .018
1
⁄2 15 4/Offset .04 .018
1
⁄2 15 4/One Side .06 .027
1
⁄2 15 6/One Side .14 .063
1
⁄2 15 3/Offset .04 .018
1
⁄2 15 4/Offset .04 .018
A Watts Wate r Technolo gies Com pany
USA: No. Andover, MA • Tel. (978) 688-1811 • Fax: (978) 794-1848 • www.watts.com
Canada: Burlington, ONT. • Tel. (905) 332-4090 • Fax: (905) 332-7068 • www.wattscanada.ca
ES-WP-PACrimpManifolds 1102 © 2011 Watts