Page 1
For Residential and Commercial Applications
ES-WP-PAAdapters
Job Name
Job Location
Engineer
Approval
LEAD FREE
–––––––––––––––––––––––––––––––––––––––––––
–––––––––––––––––––––––––––––––––––––––––
–––––––––––––––––––––––––––––––––––––––––––––
–––––––––––––––––––––––––––––––––––––––––––––
*
Poly-Alloy CrimpRing™
Adapters
Poly-Alloy CrimpRing™ Sweat Adapters are used to transition
copper pipe to WaterPEX
used for the appropriate NPT fitting.
Specifications
System shall be plumbed using Watts WaterPEX® cross-linked
polyethylene pipe. All joints shall be made using Watts brass
CrimpRing
the Watts copper CrimpRing
crimping methods as outlined in the Watts WaterPEX
Installation Guidelines.
™
and/or poly-alloy CrimpRing™ fittings using either
®
supply lines. Threaded Adapters are
™
or stainless steel CinchClamp™**
®
Contractor
Approval
Contractor’s P.O. No.
Representative
––––––––––––––––––––––––––––––––––––––––––––
–––––––––––––––––––––––––––––––––––––––––––––
––––––––––––––––––––––––––––––––––––––––
Crimp x MPT Threaded
––––––––––––––––––––––––––––––––––
WP12P
Adapter
Installation Note
CrimpRing™ Adapters must be installed in accordance with all
Watts WaterPEX
provided in WaterPEX
®
installation procedures, including information
®
installation manual and guidelines.
Approvals
• Manufactured in accordance with American Society for
Testing and Materials (ASTM) F-877 and F-2159
• Listed by the National Sanitation Foundation to NSF
Standards 14 and 61 for use in potable water systems
• Listed by NSF to be in compliant to the Uniform Plumbing
Code
• Labeled B137.5 which indicates that it is compliant to the
CSA Standards B137.5
• Manufactured from Acudel
* The wetted surface of this product contacted by consumable
water contains less than one quarter of one percent (0.25%) of
lead by weight.
** Note: Watts WaterPEX CinchClamp™ fittings should not be used
with wrot copper PEX fittings.
®
engineered thermoplastic resin.
War n i n g!
If connections must be made in temperatures below 30°F,
caution must be taken to allow the WaterPEX to form a proper
seal against the barb. Apply the connection slowly to ensure
the PEX material conforms to the barb.
Watts product specifications in U.S. customary units and metric are approximate and are provided for reference only. For precise measurements,
please contact Watts Technical Service. Watts reserves the right to change or modify product design, construction, specifications, or materials without prior notice and without incurring any obligation to make such changes and modifications on Watts products previously or subsequently sold.
Page 2
Dimensions – Weights
MODEL INLET OUTLET PKG. WEIGHT
in. mm type in. mm type lbs. kgs.
CrimpRing™ Threaded Adapters — Crimp x Male
WP12B-0808PB
WP12B-0812PB
WP12B-1212PB
1
⁄2 15 Crimp Fitting
1
⁄2 15 Crimp Fitting
3
⁄4 20 Crimp Fitting
1
⁄2 15 MPT 1 0.5
3
⁄4 20 MPT 2 0.9
3
⁄4 20 MPT 2 0.9
A Watts Water Te chn olo gie s Compan y
Canada: 5435 North Service Rd., Burlington, ONT. L7L 5H7; www.wattscanada.ca
USA: 815 Chestnut St., No. Andover, MA 01845-6098; www.watts.com
ES-WP-PAAdapters 1020 © 2010 Watts
Loading...