Watts NLF-9 User Manual
Watts Model N9/LFN9 and
Model NLF9/LFNLF9
Backflow Preventers
ATTENTION INSTALLER: After installation, please leave this Instruction Sheet for occupant’s information.
WARNING
!
You are required to thoroughly read all installation instructions and
product safety information before beginning the installation of this product. FAILURE TO COMPLY WITH PROPER INSTALLATION AND
MAINTENANCE INSTRUCTIONS COULD RESULT IN PRODUCT
FAILURE WHICH CAN CAUSE PROPERTY DAMAGE, PERSONAL
INJURY AND/OR DEATH. Watts is not responsible for damages result-
ing from improper installation and/or maintenance.
Local building or plumbing codes may require modifications to the information provided. You are required to consult the local building and plumbing
codes prior to installation. If this information is not consistent with local
building or plumbing codes, the local codes should be followed.
Need for Periodic Inspection/Maintenance: This product must be tested periodically in compliance with local codes, but at least once per year or
more as service conditions warrant. Corrosive water conditions, and/or unauthorized adjustments or repair could render the product ineffective for the
service intended. Regular checking and cleaning of the product’s internal
components helps assure maximum life and proper product function.
Installation Instructions
Before installing, flush out pipe lines to remove scale and other foreign
matter. The valves can be installed horizontally or vertically. Install the
valve in the line with the arrow on valve body pointing in the direction
of flow. Model NLF9/LFNLF9 is furnished with inlet thread gasket and
pipe dope or Teflon
is recommended for the pipe threads of Model N9/LFN9. To maintain
the valve discs in a clean operating condition, we strongly recommend a
pipe line strainer be installed in the supply line before the Model N9/LFN9
or Model NLF9/LFNLF9.
®
tape should not be used. However, Teflon® tape
Important
These devices are not intended for installation where emergency or temporary water discharge can cause water damage because they are not
designed to be spillage free under all service conditions. For this reason
and for maintenance accessibility, these devices must not be installed
inside a wall or any concealed location.
This device should be installed at the furthermost downstream end of
the supply pipe or fixture where temporary spillage due to critical flow
pressure conditions can be discharged harmlessly. Also, the backflow
preventer will operate most satisfactorily when located as far downstream as possible, because any backpressure is minimized.
Application
Watts 3⁄8" (10mm) Model NLF9/LFNLF9 is recommended for laboratory
faucets and is not suitable for continuous pressure applications. The
Model N9/LFN9 series are recommended for either continuous or intermittent pressure type installations.
Potable water must be protected from backflow of low hazard substances used in equipment container, sinks and set tubs. In the event
of negative supply pressure such contaminated fluids will not backflow
to the supply source by backsiphonage. For clarification of low hazard
substances consult Local Plumbing Authority or Health Department.
Temperature and Pressure
Maximum Pressure 150psi (10.3 bar).
Maximum Temperature 140°F (60°C).
Annual inspection of all water system safety and control valves is required
and necessary. Regular inspection, testing and cleaning assures maximum life and
proper product function.
®
Teflon
is a registered trademark of the E.I. Dupont de Nemours & Company.
IS-N9-NLF9
Watts Model N9/LFN9 and
Model NLF9/LFNLF9
Backflow Preventers
ATTENTION INSTALLER: After installation, please leave this Instruction Sheet for occupant’s information.
WARNING
!
You are required to thoroughly read all installation instructions and
product safety information before beginning the installation of this product. FAILURE TO COMPLY WITH PROPER INSTALLATION AND
MAINTENANCE INSTRUCTIONS COULD RESULT IN PRODUCT
FAILURE WHICH CAN CAUSE PROPERTY DAMAGE, PERSONAL
INJURY AND/OR DEATH. Watts is not responsible for damages result-
ing from improper installation and/or maintenance.
Local building or plumbing codes may require modifications to the information provided. You are required to consult the local building and plumbing
codes prior to installation. If this information is not consistent with local
building or plumbing codes, the local codes should be followed.
Need for Periodic Inspection/Maintenance: This product must be tested periodically in compliance with local codes, but at least once per year or
more as service conditions warrant. Corrosive water conditions, and/or unauthorized adjustments or repair could render the product ineffective for the
service intended. Regular checking and cleaning of the product’s internal
components helps assure maximum life and proper product function.
Installation Instructions
Before installing, flush out pipe lines to remove scale and other foreign
matter. The valves can be installed horizontally or vertically. Install the
valve in the line with the arrow on valve body pointing in the direction
of flow. Model NLF9/LFNLF9 is furnished with inlet thread gasket and
pipe dope or Teflon
is recommended for the pipe threads of Model N9/LFN9. To maintain
the valve discs in a clean operating condition, we strongly recommend a
pipe line strainer be installed in the supply line before the Model N9/LFN9
or Model NLF9/LFNLF9.
®
tape should not be used. However, Teflon® tape
Important
These devices are not intended for installation where emergency or temporary water discharge can cause water damage because they are not
designed to be spillage free under all service conditions. For this reason
and for maintenance accessibility, these devices must not be installed
inside a wall or any concealed location.
This device should be installed at the furthermost downstream end of
the supply pipe or fixture where temporary spillage due to critical flow
pressure conditions can be discharged harmlessly. Also, the backflow
preventer will operate most satisfactorily when located as far downstream as possible, because any backpressure is minimized.
Application
Watts 3⁄8" (10mm) Model NLF9/LFNLF9 is recommended for laboratory
faucets and is not suitable for continuous pressure applications. The
Model N9/LFN9 series are recommended for either continuous or intermittent pressure type installations.
Potable water must be protected from backflow of low hazard substances used in equipment container, sinks and set tubs. In the event
of negative supply pressure such contaminated fluids will not backflow
to the supply source by backsiphonage. For clarification of low hazard
substances consult Local Plumbing Authority or Health Department.
Temperature and Pressure
Maximum Pressure 150psi (10.3 bar).
Maximum Temperature 140°F (60°C).
Annual inspection of all water system safety and control valves is required
and necessary. Regular inspection, testing and cleaning assures maximum life and
proper product function.
®
Teflon
is a registered trademark of the E.I. Dupont de Nemours & Company.
IS-N9-NLF9
Repair Kits
Model N9/LFN9 and NLF9/LFNLF9 repair consists of; diaphragm assembly, discs assembly and a gasket.
Model NLF9
Hose Connection
Combination Fixture
N9/NLF9 Total Repair Kit
Watts Model NLF9 on
Laboratory Gooseneck
ORDERING CODE KIT NO. SIZE
886019 RK N9/NLF9 T
1
⁄4" - 3⁄8" (8–10mm)
Water Outlet
Kit includes: Diaphragm assembly, Disc assembly and gasket.
Watts Strainer
Limited Warranty: Watts Regulator Co. (the “Company”) warrants each product to be free from defects in material and workmanship under normal usage for a period of one year from the date of
original shipment. In the event of such defects within the warranty period, the Company will, at its option, replace or recondition the product without charge.
THE WARRANTY SET FORTH HEREIN IS GIVEN EXPRESSLY AND IS THE ONLY WARRANTY GIVEN BY THE COMPANY WITH RESPECT TO THE PRODUCT. THE COMPANY MAKES NO OTHER
WARRANTIES, EXPRESS OR IMPLIED. THE COMPANY HEREBY SPECIFICALLY DISCLAIMS ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE IMPLIED
WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.
The remedy described in the first paragraph of this warranty shall constitute the sole and exclusive remedy for breach of warranty, and the Company shall not be responsible for any incidental, special
or consequential damages, including without limitation, lost profits or the cost of repairing or replacing other property which is damaged if this product does not work properly, other costs resulting from
labor charges, delays, vandalism, negligence, fouling caused by foreign material, damage from adverse water conditions, chemical, or any other circumstances over which the Company has no control.
This warranty shall be invalidated by any abuse, misuse, misapplication, improper installation or improper maintenance or alteration of the product.
Some States do not allow limitations on how long an implied warranty lasts, and some States do not allow the exclusion or limitation of incidental or consequential damages. Therefore the above
limitations may not apply to you. This Limited Warranty gives you specific legal rights, and you may have other rights that vary from State to State. You should consult applicable state laws to
determine your rights. SO FAR AS IS CONSISTENT WITH APPLICABLE STATE LAW, ANY IMPLIED WARRANTIES THAT MAY NOT BE DISCLAIMED, INCLUDING THE IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED IN DURATION TO ONE YEAR FROM THE DATE OF ORIGINAL SHIPMENT.
A Watts Water Technologies Company
USA: Tel: (978) 688-1811 • Fax: (978) 794-1848 • www.watts.com
Canada: Tel: (905) 332-4090 • Fax: (905) 332-7068 • www.wattscanada.ca
IS-N9-NLF9 1209 EDP# 1910202 © 2012 Watts
Repair Kits
Model N9/LFN9 and NLF9/LFNLF9 repair consists of; diaphragm assembly, discs assembly and a gasket.
N9/NLF9 Total Repair Kit
ORDERING CODE KIT NO. SIZE
886019 RK N9/NLF9 T
Kit includes: Diaphragm assembly, Disc assembly and gasket.
Limited Warranty: Watts Regulator Co. (the “Company”) warrants each product to be free from defects in material and workmanship under normal usage for a period of one year from the date of
original shipment. In the event of such defects within the warranty period, the Company will, at its option, replace or recondition the product without charge.
THE WARRANTY SET FORTH HEREIN IS GIVEN EXPRESSLY AND IS THE ONLY WARRANTY GIVEN BY THE COMPANY WITH RESPECT TO THE PRODUCT. THE COMPANY MAKES NO OTHER
WARRANTIES, EXPRESS OR IMPLIED. THE COMPANY HEREBY SPECIFICALLY DISCLAIMS ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE IMPLIED
WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.
The remedy described in the first paragraph of this warranty shall constitute the sole and exclusive remedy for breach of warranty, and the Company shall not be responsible for any incidental, special
or consequential damages, including without limitation, lost profits or the cost of repairing or replacing other property which is damaged if this product does not work properly, other costs resulting from
labor charges, delays, vandalism, negligence, fouling caused by foreign material, damage from adverse water conditions, chemical, or any other circumstances over which the Company has no control.
This warranty shall be invalidated by any abuse, misuse, misapplication, improper installation or improper maintenance or alteration of the product.
Some States do not allow limitations on how long an implied warranty lasts, and some States do not allow the exclusion or limitation of incidental or consequential damages. Therefore the above
limitations may not apply to you. This Limited Warranty gives you specific legal rights, and you may have other rights that vary from State to State. You should consult applicable state laws to
determine your rights. SO FAR AS IS CONSISTENT WITH APPLICABLE STATE LAW, ANY IMPLIED WARRANTIES THAT MAY NOT BE DISCLAIMED, INCLUDING THE IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED IN DURATION TO ONE YEAR FROM THE DATE OF ORIGINAL SHIPMENT.
1
⁄4" - 3⁄8" (8–10mm)
Model NLF9
Hose Connection
Watts Model NLF9 on
Laboratory Gooseneck
Water Outlet
Combination Fixture
Watts Strainer
A Watts Water Technologies Company
USA: Tel: (978) 688-1811 • Fax: (978) 794-1848 • www.watts.com
Canada: Tel: (905) 332-4090 • Fax: (905) 332-7068 • www.wattscanada.ca
IS-N9-NLF9 1209 EDP# 1910202 © 2012 Watts
Loading...