™
SQC Series
Owner's Manual
This Manual is for the Installation, Operation, and Maintenance of the
WATER FACTORY SYSTEMS™
SQC3 and SQC4 Series
Reverse Osmosis (RO) Drinking Water Appliance
Installer: Leave with homeowner.
SAFETY INFORMATION
Read, understand and follow all safety information contained in these instructions prior to installation and use of the SQC Series Reverse Osmosis (RO) Drinking Water Appliance. Retain these instructions for future reference.
Intended use:
The Water Factory Systems™ SQC Series Reverse Osmosis (RO) Drinking Water Appliance is intended to connect permanently to a home plumbing system and has not been evaluated for other uses.
|
EXPLANATION OF SIGNAL WORD CONSEQUENCES |
|
WARNING |
Indicates a potentially hazardous situation, which, if not avoided, could result in death or serious |
|
|
injury and/or property damage. |
|
CAUTION |
Indicates a potentially hazardous situation, which, if not avoided, may result in property damage. |
|
CAUTION |
Indicates a potentially hazardous situation, which, if not avoided, may result in minor or moderate |
|
injury and/or property damage. |
||
|
To reduce the risk associated with choking:
•Do not allow children under 3 years of age to have access to small parts during the installation of this product.
To reduce the risk of physical injury:
•All hydro-pheumatic pressurized tanks must have an appropriate pressure relief valve installed.
•Shut off inlet water supply and depressurize system as shown in manual prior to filter removal.
To reduce the risk associated with the ingestion of contaminants:
•Do not use with water that is microbiologically unsafe or of unknown quality without adequate disinfection before or after the system. Systems certified for cyst reduction may be used on disinfected water that may contain filterable cysts. EPA Establishment Number 070595-CT-001.
•An approved air gap must exist between the RO System reject drain line and the drain line opening to meet plumbing codes.
To reduce the risk associated with irritation from Sodium Metabisulfite during installation:
•Sodium Metabisulfite (CAS 07681-57-4) is used in a 1% preservative solution within the reverse osmosis membrane.
•Do not put this system into service before the RO tank is flushed as specified in the installation instructions. Wear eye and face protection during installation.
•To request an MSDS relating to this product, call 203-238-8965 or visit the web at http://solutions.3m. com/wps/portal/3M/en_US/MSDS (click MSDS search). For emergencies, call 800-364-3577 or 651-737- 6501 (24 hours).
To reduce the risk associated with eye, skin and respiratory and digestive tract burns from Calcium Hypochlorite during installation:
•Calcium Hypochlorite (CAS 7778-54-3) granules are used for tank sanitation in this product.
•During installation, do not get in eyes, on skin or clothing. Do not ingest. Wear eye and face protection.
Keep out of reach of children.
•To request an MSDS relating to this product, call 203-238-8965 or visit the web at http://solutions.3m. com/wps/portal/3M/en_US/MSDS (click MSDS search). For emergencies, call 800-364-3577 or 651-737- 6501 (24 hours).
To reduce the risk associated with ingestion of water contaminated with sanitizer:
•Sanitizer must be flushed from the system before using as directed within the installation instructions.
To reduce the risk associated with hazardous voltage due to an installer drilling through existing electric wiring or water pipes in the area of installation:
•Do not install near electric wiring or piping which may be in path of a drilling tool when selecting the position to mount the filter bracket.
To reduce the risk of eye injury while drilling counter-tops for faucet installation:
•Safety glasses MUST be worn during the sink hole drilling operations.
To reduce the risk of injury associated with household bleach:
•Read and follow manufacturers directions and cautions
•Keep out of the reach of children
•DO NOT intermix with other chemicals
To reduce the risk of eye injury while drilling counter-tops for faucet installation:
•Safety glasses MUST be worn during the sink hole drilling operations.
To reduce the risk associated with property damage due to water leakage:
•Read and follow Use Instructions before installation and use of this system.
•Installation and use MUST comply with all state and local plumbing codes.
•Protect from freezing, remove filter cartridge when temperatures are expected to drop below 40° F (4.4° C).
•Do not install systems in areas where ambient temperatures may go above 110° F (43.3° C).
•Do not install on hot water supply lines. The maximum operating water temperature of this filter system is 100°F (37.8°C).
•Do not install if water pressure exceeds 100 psi (690 kPa). If your water pressure exceeds 80 psi (552 kPa), you must install a pressure limiting valve. Contact a plumbing professional if you are uncertain how to check your water pressure.
•Do not install where water hammer conditions may occur. If water hammer conditions exist you must install a water hammer arrester. Contact a plumbing professional if you are uncertain how to check for this condition.
•Where backflow prevention device is installed on a water system, a device for controlling pressure due to thermal expansion must be installed.
•Do not use a torch or other high temperature sources near filter system, cartridges, plastic fittings or plastic plumbing.
•On plastic fittings, never use pipe sealant or pipe dope. Use PTFE thread tape only, pipe dope properties may deteriorate plastic.
•Take care when using pliers or pipe wrenches to tighten plastic fittings, as damage may occur if overtightening occurs.
•Do not install in direct sunlight or outdoors.
•All hydro-pneumatic tanks must have an appropriate pressure relief valve installed.
•Do not install near water pipes which will be in path of a drilling tool when selecting the position to mount the bracket.
•Mount filter in such a position as to prevent it from being struck by other items used in the area of installation.
•Ensure that the location and fasteners will support the weight of the system when installed.
•Ensure all tubing and fittings are secure and free of leaks.
•Do not install unit if collet is missing. Contact Water Factory Systems if collets are missing from any fittings.
•SHUT OFF FUEL OR ELECTRIC POWER SUPPLY TO WATER HEATER after water is shut off.
•The disposable filter cartridge MUST be replaced every 12 months, or sooner if a noticeable reduction in flow rate occurs.
•The RO Membrane cartridge MUST be replaced at least every 36 months.
•Failure to install, operate, or maintain your drinking water appliance in accordance with these use instructions or any other installation or use instructions accompanying this product may result in product failure and property damage, including water leakage and will void warranty.
INTRODUCTION
This manual explains the installation, operation and maintenance of the Water Factory Systems™ SQC Series Reverse Osmosis (RO) Drinking Water Appliances. Please read each section of this manual carefully. The specific model chosen should be appropriate for the local water conditions and the customer’s needs. Check the Performance Data Sheet for the performance characteristics and the conditions of use.
The Water Factory Systems undercounter RO drinking water appliances are designed to connect permanently to a home plumbing system. To ensure that the installation conforms to your state and local plumbing codes, it is recommended that the installation be performed by a qualified installation specialist for RO drinking water appliances or a licensed plumber. Failure to install the system as instructed will VOID the warranty.
|
TABLE OF CONTENTS |
|
I. Installation Instructions |
|
|
A. |
Determine the appliance location.................................................................................... |
3 |
B. |
Prepare the area for installation...................................................................................... |
3 |
C. |
Prepare the appliance for installation............................................................................. |
4 |
D. |
Make the faucet mounting hole....................................................................................... |
4 |
E. |
Mount the faucet............................................................................................................. |
5 |
F. |
Install Stem Adapter With 1/4” Feedwater Tube Outlet.................................................. |
6 |
G. |
Prefill and sanitize the storage tank................................................................................ |
6 |
H. |
Install the drain connection............................................................................................. |
7 |
I. |
Install the filtration assembly and storage tank............................................................... |
7 |
J. |
Make the tubing connections.......................................................................................... |
8 |
K. |
Install the icemaker hookup (optional)............................................................................ |
8 |
L. |
Start up the appliance..................................................................................................... |
8 |
M. |
Flush the appliance of the preservative and check the operation.................................. |
9 |
N. |
Cleanup & paperwork..................................................................................................... |
9 |
O. |
Appendix for basement installations............................................................................... |
11 |
P. |
Installation troubleshooting............................................................................................. |
12 |
II. Operation & Maintenance Instructions |
|
|
A. |
Important water quality assurance requirements............................................................ |
13 |
B. |
Replacing the filter cartridges......................................................................................... |
13 |
C. |
Replacing the RO membrane cartridge.......................................................................... |
13 |
D. |
Sanitizing the RO appliance............................................................................................ |
14 |
E. |
Long term non-use.......................................................................................................... |
15 |
I. Installation Instructions
A.DETERMINE THE APPLIANCE LOCATIONS
The appliance can be located under a sink or in a base-
ment depending on space availability and the customer’s preference. If a basement installation is selected, additional tubing, hardware and fittings may be needed and a hole will have to be made from inside the cabinet, through the floor, to the basement. Never install it in an area of the home where the temperature may drop below 40°C, because damage to the appliance may occur.
The exact placement of the various components of the appliance will vary from installation to installation. The installer, in conjunction with the customer, must decide on where to place the faucet, tank and filtration assembly by balancing the homeowner’s convenience with ease of installation and servicing. (See Fig. 1 & 7)
Considerations for an icemaker or other remote hookup should be predetermined, including routing and any additional tools, fittings, and tubing that may be required.
B.PREPARE THE AREA FOR INSTALLATION
Remove supplies from under the sink and stack them
neatly away from the working area. Arrange a light for the work area, if necessary.
If a basement installation is called for, determine where the components will be located and how they will be mounted. Special mounting brackets and hardware may be necessary to secure the appliance to a wall or ceiling joists. (See Figure 7) Inspect the cold water supply line and determine if any
special fittings, in addition to what is included in the kit, are required.
NOTE: It is a good idea at this time to check the condition of the undercounter plumbing for any existing or potential leaks. Make sure to perform any necessary repairs prior to the installation of the drinking water device.
|
|
1/4" Green |
|
|
Tubing |
|
|
Red SFC Tubing |
|
Reducing |
Storage Tank Valve |
|
Union |
Pressure Relief Valve |
|
3/8" Black |
(required, not included) |
|
|
|
Feedwater |
Tubing |
3/8" Yellow |
Connection |
|
Tubing |
Placement |
|
|
3/8" Blue
Tubing
1/4" Orange
Tubing
Drain
Saddle
Sink Drain
Storage Tank
Filtration System
Fig. 1
3
Loading...