Water Factory Systems FM1500 User Manual

™

Owner's Manual

This Manual is for the Installation, Operation,

and Maintenance of the

™

WATER FACTORY SYSTEMS

Faucet MATE™ FM DWS 1500

™

Drinking Water Appliance

98-91122 1009 Installer: Leave with Homeowner.

Introduction

This manual explains the installation and maintenance instructions for the CUNO/Water Factory Systems™ FaucetMATE™
FM DWS 1500. Please read each section of this manual carefully. The specific model chosen should be appropriate for the
local water conditions and the customer’s needs. Check the Performance Data Sheet which specifies performance
characteristics and the conditions of use.

This CUNO/Water Factory Systems drinking water appliance is designed to connect permanently to a home plumbing system.
To ensure the installation conforms to your state and local plumbing codes, it is recommended that the installation be
performed by a qualified specialist for drinking water appliances or a licensed plumber. Failure to install as instructed will

VOID the warranty.

Table Of Contents

Installation Instructions

Installation Precautions ..............................................................................................................................3

Determine System Location .......................................................................................................................3

Prepare The Area For Installation ...............................................................................................................3

Prepare The Appliance For Installation .......................................................................................................4

Locating The Faucet ...................................................................................................................................4

Make The Faucet Mounting Hole ................................................................................................................4

Mounting The Faucet ..................................................................................................................................5

Mounting The Drinking Water Filtration Appliance .....................................................................................5

Installing The Feed Water Valve/Adapter ....................................................................................................5

Make Tubing Connections ..........................................................................................................................5

Procedure For Installing FM DWS 1500 Water Appliance ..........................................................................6

Replacement Cartridge Change Instructions ..............................................................................................7

Illustrations

System Location (Figure 1) ........................................................................................................................8

Faucet Installation (Figure 2) ......................................................................................................................9

How To Use ‘Push-In’ Connections (Figure 3) ...........................................................................................9

2

Installation Precautions

Procedure for Installing

• The filter must be installed with the inlet and outlet ports
as labeled. Make sure not to reverse con nec tions.

• Do not install on hot water line. Maximum

temperature allowed is 100°F (38°C).

• Do not install on line pressure above 125 psi

(862 kPa).

• Do not use torch or other high temperature
sources near filter head or plas tic cartridge.

• Do not install near electric wires or water pipes which
will be in path of drill when selecting the position to
mount the bracket.

• Do not install in direct sunlight.

• Protect from freezing. Drain filter when room temperature
drops be low 40°F (4.4°C).

• Allow minimum of 2" (5 cm) clear space under filter to
facilitate car tridge change.

• Mount filter in such a position as to prevent it from being
struck by oth er items, such as wastebaskets, etc.

• Do not use with water that is microbiologically unsafe or
of unknown quality without adequate disinfection before
or after the system. Systems certified for cyst reduction
may be used on disinfected waters that may contain
filterable cysts.

FM DWS 1500

A. Determine System Location

The filtration system can be located under a sink. Never
install in an area of the home where the temperature may
drop to freezing as damage to the system will result.
The exact placement of the various components of the
appliance will vary from installation to installation. The
installer, in conjunction with the customer, must decide on
where to place the faucet and filtration system by balancing
the homeowners convenience with ease of installation and
servicing. (See Fig. 1)

B. Prepare The Area For Installation

Remove supplies from under the sink and stack them neatly
away from the working area. Arrange a light for the work area,
if necessary. If a basement installation is called for, determine
where components will be located and how they will be
mounted. Special mounting brackets and hardware may be
necessary to secure the system to a wall or ceiling joints.
Inspect cold water supply line to determine if any special
fittings, in addition to what is included in the kit, are
required.

NOTE: It is a good idea at this time to check the condition
of the customer’s undercounter plumbing for any existing
or potential leaks. The customer should be advised of any
problem so there is no mis under standing of who is
responsible.

• System installation must comply with existing
state or local plumbing codes.

• IMPORTANT: Some local plumbing codes may prohibit
the use of saddle-type valves and/or drain connections.
The use of saddle-type valves are prohibited in Alaska,
Delaware, Idaho, Kentucky, Massachusetts, Michigan,
Minnesota, New Hampshire, Ohio, and South Dakota.
Check your local plumbing codes for any restrictions
that apply. Massachusetts CMR 248 strictly prohibits the
use ofsaddle-type valves. The feed water connection
must conform to applicable plumbing codes.

3