Wasp Bar Code WDT2200 User Manual

6. Get Familiar with the Keyboard

Press [CMD] plus the desired
function key (located near the bottom of the
keypad) to perform commands F5 through
F8 or to input special characters that
appear in yellow on some keys.



Press [ALPHA] to toggle between
Numeric (block cursor) and Alphabetic
(underscore cursor) entry modes.
Characters are selected by quickly pressing
a key one, two or three times.

Press [SP] to input a space (blank)

character.

In Command or Supervisor mode,

press [ESC] to return to the previous menu.

In Numeric or Alphabetic Mode,
press [C] to clear the last character entered
(backspace).

7. Learn to Navigate the Modes

Beginning with the WDT2200 powered off,



press and hold these three keys in the
sequence shown to get to the Start Menu:

<< START MENU >>

1.SUPERVISOR

2.WARM START

3.COLD START

Press the [1] key at the Start Menu, then
supply the default password “2200” and
press [ENT] to access Supervisor Mode:

1.DEV 2.TERM

3.MEM 4.FORM

5.PWR 6.PSWD

7.SYS 8.DIAG

The Supervisor Menu allows access to
Language, baud rate, and barcode
symbology selection as well as Form
Caching and functions. Press the [ESC]
key to exit to the Ready Mode:

WDT2200 v1.10
MEM 2560 KB
>

In Ready Mode, press and hold the [CMD]
key for two seconds to enter User Mode:

1.RUN 2.TER

3.COM 4.DIR

5.ERA 6.TYP

7.CPY 8.SET



WDT2200

Quick Start

Guide





Use [ENT] as an Enter key to

terminate entry of text, for example.

When an application has
enabled the built-in scanner, press the
large yellow scan key to read a barcode.

See p. 15 of the WDT2200 User Reference Guide on

the CD in the docs folder for more information on

User Mode. Press [ESC] to exit, then turn off the unit.

You are now ready to install and use
Wasp’s AppGen Pro software. Insert



the AppGen CD-ROM and run setup.exe



© 2003 Wasp Technologies, Inc.



7 Steps for Getting Started
with the WDT2200

1. Remove the Lens Protectors

Remove the protective films from the LCD
display and the scanner lens. This film can
interfere with barcode scanning.

2. Open the Battery Compartment

Remove the battery door from the rear of
the WDT2200 by turning the screw on the
battery cover counterclockwise.

Data loss will occur if you remove the
CR2032 Lithium backup battery that
resides in the lower compartment.

• If you have a communications /
charging cradle for the WDT2200:

This battery does not have to be replaced
until prompted by a warning message. If
you see a transparent film insulating the
backup battery, please remove it now.

3. Install the Main Battery

Insert the rechargeable Lithium Ion battery
pack into the main battery chamber,
sliding the end with two protruding
terminals into position first.



Reinstall the battery door and tighten the
screw by turning it clockwise.

4. Connect the Communications
Cable and Charge the Main
Battery

Connect the cable’s RS-232 connector to
an available serial port on the back of your
PC. Plug the power adapter into a 120V
AC outlet. Connect the power cord to the
rear of the RS-232 connector.

Place the WDT2200 in the cradle to begin
the charging cycle. When the red LED
turns green, the battery is fully charged.
(Note: The LED on the cable itself is
always green when powered and
connected to a cradle.)

• If your WDT2200 is not equipped with
a cradle:

Attach the cable directly to the WDT2200.
The cable’s LED will be red while
charging, then green when the battery is
fully charged.

Charging will require 2 to 3 hours.

5. Power on the WDT2200

Press the red and white power key to turn
on the WDT2200. (Note: To turn the unit
off, press and hold the power key for about
one second.)