Waring MX1200XTP Installation Manual

Hi-Power Blender

Licuadora de alta potencia

Mélangeur/Bol mixeur à haute puissance

MX1200XTX/MX1200XTP/MX1200XTS

OPERATING MANUAL

MANUAL DE INSTRUCCIONES

MANUEL D'UTILISATION

IMPORTANT SAFEGUARDS

When using electrical appliances, basic safety precautions should
always be followed including the following:

1.

READ ALL INSTRUCTIONS.

2. To protect against risk of electrical shock, do not put appliance in
water or other liquid.

3. Always unplug from outlet prior to handling or cleaning.

4. This appliance is not intended for use by persons (including
children) with reduced physical, sensory or mental capabilities, or
lack of experience and knowledge, unless they have been given
supervision or instruction concerning use of the appliance by a
person responsible for their safety.

Children should be supervised to ensure that they do not play with

the appliance.

5. Unplug from outlet when not in use, before putting on or taking off
parts, and before cleaning.

6. Avoid contact with moving parts.

7. Do not operate any appliance with a damaged cord or plug or
after the appliance malfunctions or is dropped or damaged in any
manner. Return appliance to the nearest authorized service facility
for examination, repair, or electrical or mechanical adjustment.

8. The use of attachments, including canning jars, not recommended
by the appliance manufacturer may cause hazards.

9. Do not use outdoors.

10. Do not let cord hang over edge of table or counter, or touch hot
surfaces.

11. Keep hands and utensils out of container while blending, to prevent
the possibility of severe personal injury and/or damage to the
blender. A rubber scraper may be used, but must be used only
when the blender is not running.

12. CAUTION: Blades are sharp. Handle carefully.

13. Always operate blender with lid in place.

14. When blending hot liquids, remove center piece of two-piece cover.
See hot blending instructions, page 5.

15. The use of ear protection is recommended during extended
operating periods.

16. Do not leave blender unattended while it is running.

17. See cleaning and sanitizing instructions, pages 6-8.
NOT FOR WATERJET CLEANING.

GROUNDING INSTRUCTIONS

• For your protection, this appliance is equipped with a 3-conductor cord set.

• 120 Volt units are supplied with a molded 3-prong grounding-type plug
(NEMA 5-15P) and should be used in combination with a properly connected
grounding-type outlet as shown in Figure A.

If a grounding-type outlet is not available, an adapter, as shown in Figure B,

may be used to enable a 2-slot wall outlet to be used with a 3-prong plug.*

As shown in Figure C, the adapter must be grounded by attaching its

grounding lug under the screw of the outlet cover plate.

Caution: Before using an adapter, it must be determined that the outlet

cover plate screw is properly grounded. If in doubt, consult a licensed
electrician.

Never use an adapter unless you are sure it is properly grounded.
*NOTE: Use of an adapter is not permitted in Canada and Europe.

Green/Yellow: Earth Ground. Blue: Neutral. Brown: Live.

NOTE: User-installed cord set plugs are not permitted in Europe.

MX1200XTX/MX1200XTP/MX1200XTS

BLENDER SPECIFICATIONS

• Capacity: 64 oz. Working Capacity

(48 oz. capacity – MX1200XTP)

• Switch Settings: (speeds) Variable Pulse

• Speed (RPMs) 1,500–20,000 30,000

• Rating: 120 Volts - 13.0 Amps

• Base Material: Polycarbonate

• Bearing: High Precision Ball Bearing

• Cord: 6-Foot Three-Conductor Ground Cord with Strain Relief in Base

• Overall Height: 19 Inches

• Weight: 15 lbs

ETLUS, NSF listed

•

C

• Operating Cycle: 1 min. ON /3 min. OFF

SAVE THESE INSTRUCTIONS

2 3

MX1200XTX/MX1200XTP/MX1200XTS OPERATION

1. Before starting, make sure that the blender is unplugged.

2. With the unit in Off position, place container on blender base. Be sure
container is fully seated and that drive coupling is properly engaged.
Plug blender cord into outlet.

3. Put ingredients into container and cover it. Do not fill above MAX line.

4. This blender has variable speed controls. Set blender to desired speed
between 1 and 10.

5. The left paddle switch defaults to the VARIABLE setting in order to use
the speed adjustment option. Press right paddle switch up to the ON
position.

6. When finished blending, set paddle
switch to Off position.

7. This blender is equipped with a
pulse option. Hold left paddle switch
in down position to engage pulse
function. Unit will run on max speed
(30,000 RPMs) until the paddle switch
is released.

8. Allow motor to come to a complete
stop before removing container
from blender base. Never place
the container on the motor base or
remove it from the motor base while
motor is running.

9. Always hold container with one hand when starting and while blending.
Never operate without jar lid.

10. Wash and dry container after each use. See cleaning and sanitizing
instructions, pages 5-7.

RESETTING THERMAL PROTECTION

• Your blender is equipped with an automatic reset function to protect
the motor from overheating.

• If your blender stops running under heavy use, turn the power switch
Off and unplug the power cord. Empty the blender container of all
its contents and allow between 5 to 30 minutes for the motor to
cool down.

• Plug the power cord back into the outlet and continue blending.

• If your blender does not function properly following this procedure,
discontinue use and contact a certified Waring Customer Service Center.

IMPORTANT

HOT BLENDING INSTRUCTIONS

To minimize the possibility of being scalded when blending hot materials,
the following precautions and procedure must be observed.

• Hot materials are those that are 100°F (38°C) or hotter.

• Limit the amount of materials processed to 1 pint.

• Completely remove the center portion of the two-piece container lid
before starting motor (this will allow venting of the rapidly heated and
expanding air inside the container when blender is running).

• Always start blending on lowest speed setting, and then progress to
desired speed.

• Never stand directly over blender when it is being started or while it
is running.

CLEANING AND SANITIZING INSTRUCTIONS

THE CONTAINER MUST BE CLEANED AND DRIED AFTER EACH USE
OF THE BLENDER ACCORDING TO THE FOLLOWING INSTRUCTIONS.
FAILURE TO DO SO MAY ALLOW RESIDUES OF PROCESSED MATERIAL
TO COLLECT ON THE INTERNAL SEALS OF THE BLADE ASSEMBLY,
RENDERING THEM INEFFECTIVE.

Wash, rinse, sanitize and dry container prior to initial use and whenever it

•

will not be used again within a period of 1 hour.

Wash and rinse container after each use.

•

Clean and sanitize motor base prior to initial use and after each use.

•

Washing solutions based on non-sudsing detergents and chlorine-based

•

sanitizing solutions having a minimum chlorine concentration of 100 PPM
are recommended.

The following washing, rinsing, and sanitizing solutions, or their equivalents,
may be used.

SOLUTION PRODUCT DILUTION IN WATER TEMPERATURE

Washing Diversey Wyandotte 4 tablespoons Hot 115˚F (46˚C)

Diversol BX/a or CX/A /gallon

Rinsing Plain Water Warm 95˚F (35˚C)
Sanitizing Clorox® 1 tablespoon/gallon Cold 50-70˚F

Institutional Bleach (10-21˚C)

In repetitive batch-processing applications, frequent cleaning of the

•

container will prolong the life of the blade assembly. In no case should
actual running time between cleanings exceed one-half hour.

Do not use container to store processed foods or beverages.

•

4 5

TO WASH AND RINSE CONTAINER

1. REMOVE CONTAINER FROM MOTOR BASE. Remove lid. Rinse
container interior and lid under running water. Add washing solution to
container. Scrub and flush out the container interior and lid to dislodge
and remove as much food residue as possible. Empty container.

2. Wipe down exterior of container with a soft cloth or sponge dampened
with washing solution. Wash lid and lid insert in fresh washing solution.
Fill container one-quarter full with fresh washing solution, cover (with
lid only), place on motor base and run on high speed for one (1) minute.
Empty container.

3. Repeat step (2) using clean rinse water in place of washing solution.

IMPORTANT

NOTE: IN ORDER TO MINIMIZE POSSIBILITY OF SCALDING,
TEMPERATURE OF WASHING SOLUTION AND RINSE WATER MUST
NOT EXCEED 115˚F (46˚C), AND QUANTITY USED MUST NOT EXCEED
ONE-QUARTER CONTAINER FULL.

IF HIGHER TEMPERATURES OR LARGER QUANTITIES ARE USED,
OBSERVE ALL PRECAUTIONS GIVEN IN THE OPERATING MANUAL UNDER
“HOT BLENDING INSTRUCTIONS”, page 5.

TO SANITIZE AND DRY CONTAINER

1. Wipe down exterior of container with a soft cloth or sponge dampened
with sanitizing solution.

2. Fill container with sanitizing solution, cover, place on motor base, and
run on high speed for one (1) minute. Empty container. Dislodge any
residual moisture from blade assembly by placing empty container on
motor base and running on high speed for two (2) seconds.

3. Sanitize lid and lid insert by immersing in sanitizing solution for two
(2) minutes.

4. Do not rinse container, lid, or lid insert after sanitizing is completed.
Allow parts to air dry.

TO CLEAN AND SANITIZE MOTOR BASE

1. UNPLUG POWER CORD. Wipe down exterior surfaces of motor base
with soft cloths or sponges dampened with washing solution, rinse
water, and sanitizing solution. Prevent liquid from running into motor
base by wringing all excess moisture from cloths or sponges before
using them.

DO NOT IMMERSE MOTOR BASE IN WASHING SOLUTION, RINSE WATER
OR SANITIZING SOLUTION.

2. Allow motor base to air dry before using.

Any other servicing should be performed by an authorized service

representative.

SERVICE

Refer to the list of Authorized Service Centers enclosed with your Waring®
Commercial Blender for the name of the nearest Service Center, or
write to:
Waring Factory Service Center
314 Ella T. Grasso Avenue
Torrington, CT 06790
[phone]

Ship blenders for repair to the above address or to an Authorized Service
Center. Do not ship to a Waring Sales Office.

Note: If your application involves the processing of biologically active

material, we request that any items returned for service be sterilized
before being shipped. Such items must be clearly identified as having
been sterilized, both by a tag on the item itself and by a statement in
the accompanying correspondence. Waring will not accept delivery of
any return unless it is so identified.

Replacement parts for your out of warranty repairs are obtainable at the
below address.

LIMITED THREE-YEAR MOTOR WARRANTY

LIMITED TWO-YEAR WARRANTY

Waring warrants every new Waring® Commercial Blender to be free from defects
in material and workmanship for a period of two years from the date of purchase
when used with foodstuffs, nonabrasive liquids (other than detergents) and
nonabrasive semi-liquids, providing it has not been subject to loads in excess of
the indicated rating. In addition, the motor in this appliance has a full three-year
warranty.

Under this warranty, Waring, during the warranty period, will repair or replace
any part which, upon our examination, is defective in materials or workmanship,
provided the product is delivered prepaid to the Waring Service Center at: 314 Ella
T. Grasso Ave. Torrington, CT 06790, or any Factory Approved Service Center.

This warranty does not: a) apply to any product which has become worn, defective,
damaged or broken due to misuse or due to repairs or servicing by other than the
Waring Service Center or a Factory Approved Service Center, or due to abuse,
misuse, overloading or tampering; or b) cover incidental or consequential
damages of any kind.

The two-year warranty is applicable only to appliances used in the United States
or Canada; this supersedes all other express product warranty or warranty
statements. For Waring products sold outside of the U.S. and Canada, the
warranty is the responsibility of the local importer or distributor. This warranty
may vary according to local regulations.

Warning: This warranty is void if appliance is used on Direct Current (D.C.)

WARING COMMERCIAL
314 Ella T. Grasso Ave.
Torrington, CT 06790

6 7