Wanhao Duplicator 8 Quick guide
4.1.2
1 5
DOWNLOAD AND INSTALL SOFTWARE PREPARE DUPLICATOR 8 FOR PRINTING
Download the Chitu software from the link below based on your
PC System.
https://www.chitubox.com/download.html?fbclid=IwAR3Jn2D91b42Pj
fRIIKMezmtvTTCIWu7ne88i_KXEofp7ryCGL6Z0M7FT9Y
Follow up with steps
and Install the software.
2
D8 SETTINGS
2.1
Click on Setting and choose D8 printer and click on OK.
D8 printer Displays and settings are pre congured.Based on
the model and your preferences you can modify setting in these
menus.
3
SLICING PROCESS
3.1
After you ensure the setting click on Slice.
3.2
In the Slicing process you can see the printing time and
other information about the model. You can also slide the
slider to up and down and see the layers of the model you
are going to print.
Click on Export and save the le as a Zip le.
In the Home Screen press on CWS BY USB, Choose the
Sliced le press on Print Now, Printer starts to load the model and
lower the building platform and the printing process begins.
4.2
Printing by WIFI
4.2.1
Insert the Dongle
5.0
Preparing Printer
5.1
Plug the power cord and turn on the printer, Printer starts to
boot up. Wait until you access to Home Screen.
5.2
Slid the vat smoothly on the LCD screen and align the spots
on the Vat with two knobs on the left and right.
2.2
Load a model on the platform.
2.3
In this bar you can add supports automatically and
manually to your model.
Slicer starts to write and save the le.
4
PRINTING PROCESS
4.1
Printing by USB
4.1.1
After slicing process copy the sliced model into the
USB memory that comes with printer or any other USB
memory that you prefer to place the le in.
4.2.2
Go to setting and choose WiFi
4.2.3
Click on the available WiFi and enter your password.
4.2.4
After success connection, input the IP address given by
printer in your PC web browser and connect to D8.
4.2.5
Upload the File
4.2.6
Press on Print Now
5.3
Tighten the knobs on the both side, Make sure tight them
enough and don’t put too much Pressure.
6.0
Mounting printing platform
6.1
Mount the printing platform on the holding plate and tighten
two knobs on top of it, Make sure is tight enough that the printing
platform does not move or shake.
B C
6.2
Loosen four knobs on the printing on the right and
the left side of the platform.
6.3
On Home Screen Press on Setting> Z Height >Reset.
Building platform starts to lower and home positioning.
7.0
Pouring resin
7.1
In order to pour the resin into vat your need to lift
the printing platform. Press on upper icon for few times and
give a good distance between vat and printing plate. Shake
the bottle continuously before open it then pour the resin
inside the vat as shown in the pictures below.
WANHAO DUPLICATOR 8
GETTING STARTED GUIDE
6.4
After the platform homed and reached into the vat, with
little bit of press tighten the four knobs in front and the back
of printing plate.
POST PROCESSING
Place the platform to a washing-up bowl. Remove the objects by
sliding the scraper in at their base.Wash off any liquid polymer
in alcohol container. You can gently clean it with a soft brush or
sponge,take care not to damage it, it will not achieve full hardness
until after post exposing in light. An ultrasonic cleaner will clean
your objects without the possibility of damaging them.
Check your object is thoroughly clean as resin cannot be easily
removed afterwards and then leave it under water in sunlight for
about 10 minutes. The longer you leave it
under water the darker the colour will get,
some colour change is inevitable. When
it is completely post-exposed it will be
strong and have a dry surface. Empty the
contents of the vat back into the bottle by
pouring through a sieve.With the vat on
a at surface wipe the inside thoroughly
with absorbent paper.Replace the lm
when damaged.
D
WANHAO FACTORY CO.,LTD
NO.198 Gaoke Road FuYang HangZhou China
WANHAO Help Desk: 86-571-23290996
(Operating Hours: Mon-sat ; 8:00am -5:00pm)
www.wanhao3dprinter.com
support@wanhao3dprinter.com
REV 1.1
Loading...