WANHAO Duplicator 5S, Duplicator 5S Mini User Manual

LCD Layout

© Wanhao USA 2015 www.wanhaousa.com

Wanhao Duplicator 5S & Duplicator 5S MINI Heated Build Plate kit

User Manual

Power Indicator

Temperature Display

Scroll

UP/DOWN

Buttons

SET/Enter Button

Operation

1

.

Set Target Temperature：

target temperature.Now press or

temperature.

2.

Second Menu：

Menu setting will

for 6 seconds

Hold

be

displayed. Scroll by pressing

to set .

3. Once you have scrolled to the desired menu setting you can
adjust this setting by holding the button and clicking the
or button simultaneously.

Press

gently to blink display the

to change the target

to enter second menu.

or

Power Switch

Hold ,then press or

to scroll through options.

represents Heating Mode,

represents Cooling Mode.

Hold ,then press or

to scroll through options.

Choose lowest temperature limits:

－1 9.9℃ to -1.0℃

Hold ,then press or

to scroll through options.

Choose highest temperature limits:

+1.0℃ to 99.9℃

Second Menu Codes

Code

Funct ion

Heating/Cooling

Low Temperature Limit

High Temperature Limit

Del ayed Tim e

Temperature Correction

Temperature Return Difference

*IMPORTANT: Before operation you will
need to set up the "temperature return
difference" in order for your device to
maintain a set temperature within 1-15
degrees. If you set this value to 1 then your

device will turn back ON the heater within

-1 degree from the targeted temperature. If
you set this value to 15 then your device
will turn back ON the heater within -15
degrees from the targeted temperature.

Default setting value is 1.

Hold then press or

to set delayed start time from

0 to 5 minutes.

Hold then press or

to scroll through options.

Choose temperature correction:

- 15.0℃ to 5.0℃

Hold then press or

to scroll through options.

Choose return difference:

1℃ to 15℃

Device Error: When there is an

open or short circuit the error
code“EI” will be displayed.

Troubleshooting

© Wanhao USA 2015 www.wanhaousa.com

Failure

No display when

power is ON.

Display is ON but

device is not working.

Displayed temperature

is unstable

Difference between target

temp. and the current

stable temp. is too wide in

range.

Heating continues past

target temperature.

Device cannot maintain
target temperature.

"EI" is displayed.

Possible Cause

Possible wall outlet failure, short circuit,

cable disconnection, and/or switch failure.

The set temperature is higher than the current
temperature; or
The heat protector has shut off the device due to
unsafe pressure.

The blue sensor cables are experiencing interference, are

poorly connected, and/or are tied to other cables; or

The power to the device is limited due to cable damage.

The blue sensor cables are incorrectly

connected and the resistance is too strong; or

The blue sensor cables are damaged.

The blue sensor cables are incorrectly installed; or

The compressor contact is failing.

The target temperature return difference has

not been set to the correct value.

There is an open or short circuit in the blue sensor
cables.

Check safety fuses at main power box for correct

operation. If device is still not working contact dealer/

purchase source for further instructions.

Reset the target temperature. Check device and
Heating Build Plate for loose cabling, damage, and/
or signs of overheating.

Separate blue sensor cables from power cables. You may
also need to replace the shielded cable tubes/sheaths.
Check that connector is in good condition.

Check that the blue sensor cables have enough separation
from power cables. Make sure that the blue sensor cables
are not damaged. Sensor cable may need replacement.

Check to make sure the blue sensor cables are
correctly connected. Also check that the connector
is in good condition.

Reset the return difference value. Adjust this setting
in larger increments until you find a working value.

Check to see if the wiring has a good contact with the
connector terminal.

Remedy

WARNING!

*Adjusting or changing wiring to and within this device may cause electrical shock resulting in bodily harm and/
or damage to your Heated Buid Plate kit. Do not tamper with this device unless you are skilled in electronics.
The temperature controller is sold as part of a Heated Build Plate kit and as such should only be used with this
kit. If you are having

an issue with your device or any of the components of the Heated Build Plate kit please
contact your dealer or purchase source for instructions on how to receive technical help, service, and/or a
replacement.

*3D printing filaments that require a Heated Build Plate kit may give off toxic fumes...make sure to use proper
ventilation whenever using your Heated Build Plate kit.

*If you notice anything potentially dangerous during operation please turn off this device, unplug from wall
outlet, and contact your dealer/purchase source for further help.