COPPER - installation guide
en
1
COPPER - installation guide
en
WBCP-C-IG-001-EN
plug & drive
COPPER
INSTALLATION
GUIDE
COPPER - installation guide
en
2
SECURITY PRESCRIPTIONS
CONTENTS
Disregard of or actions contrary to the safety information and instructions contained in this manual and printed on the device
may lead to electric shock, fire and/or severe injury and either damage to the vehicle’s battery or to the Wallbox device. Any
resulting damage from such actions is excluded from the warranty.
The installation of the Wallbox device must be performed by a qualified electrician in accordance with the perceptive regula-
tion.
The information provided in this Installation Guide does not relieve the user of responsibility to follow all norms and standards
or local regulations that may apply.
The Wallbox charger device has been designed, developed and manufactured to satisfy requirements, safety dispositions and
norms in accordance with the directives presented in the declaration of conformity (view Users Guide).
The user must read and understand in its entirety the safety instructions here provided.
SECURITY PRESCRIPTIONS 2
SAFETY INSTRUCTIONS 3
PRODUCT DESCRIPTION 4
INSTALLATION INSTRUCTIONS 6
PRECAUTIONS 6
DIMENSIONS & POSITIONING 7
DRILL & MOUNT 8
STARTUP 10
TROUBLESHOOTING 10
MAINTENANCE 10
WARRANTY 10
Follow all of the safety instructions and take special care to keep this manual handy. This installation
manual is intended for qualified personnel only.
COPPER - installation guide
en
3
SAFETY INSTRUCTIONS
• Do not operate in case of observing physical defects, such as cracks, breaks, corrosion or other damage. In this case
please contact your distributor to get the Wallbox device replaced.
• Only authorized specialist can open, disassemble, repair, manipulate or modify the Wallbox device. Unauthorized modi-
fication of the Wallbox equipment voids the manufacturer’s warranty.
• Unauthorized modifications or conversions are forbidden.
• Do not remove any notices on the device, such as safety symbols, warning notices, rating plates, nameplates or cable
markings.
• Protect your Wallbox device from any impacts or waypoints to wich it could be exposed.
• The charging station does not have its own power switch. Always follow your local electrical regulations and norms, as
applicable.
• The Wallbox chargers can only be used under the specified operating parameters and within the normal environmental
conditions described on Product description.
• Do not use your Wallbox charger under inclement weather conditions that could aect either the vehicle or the Wall-
box device. Do not open the connector panel cover in the rain.
CONNECTOR RECOMMENDATIONS
• Always check the charging cable and contacts for damage and contamination before using them.
• Never use a damaged charging cable, vehicle inlet, or infrastructure socket outlet for charging.
• Never use contacts that are dirty or wet.
• Only connect the charging cable to vehicle inlets and infrastructure socket outlets that are protected against water,
moisture and liquids.
• After stopping the charging process the vehicle connector and the infrastructure plug can be disconnected. Never
use force to disconnect the vehicle connector from the vehicle inlet and the infrastructure plug from the socket outlet.
Such dangerous actions can lead to serious injuries or even death.
• Depending on the charging station and the electric vehicle the termination of the charging process and the duration of
unlocking may vary.
• There are electric vehicles that can be started with a connected charging cable. Always make sure to disconnect the
charging cable before driving away.
• Do not use the charging cable with an extension cable or an adapter.
• If the connector emits smoke or starts melting, never touch the charging cable. If possible, stop the charging process.
In any case, disconnect the power supply of the Wallbox device..
• Make sure that the charging cable is out of reach of children. The charging cable may only be used by persons with a
valid driver’s license for motor vehicles.
• Be particullary careful with the connector, do not step on it or its cable.
• The cable must NOT UNDER ANY CIRCUMSTANCES be strained when connected to the vehicle.
COPPER - installation guide
en
4
INTRODUCTION
Wallbox is a revolutionary system of smart charging for electric vehicles, equipped with the latesttechnology and a functional
and sophisticated design to deliver the best performance in the daily life of individuals and companies.
• The Wallbox device has been conceived for private and semi-public use, in such places as private land, company car
parks and depots.
• The Wallbox device is used exclusively for charging electric and plug-in hybrid vehicles.
• The Wallbox device is an smart charger provided with connectivity functionalities.
Wallbox software allows our technical support service to solve any issue remotely, no wait times and no need to set appoint-
ments and almost instantaneously
The Wallbox device is provided with an specific Electric Vehicle Connector (EVC). Depending on the version acquired it
comes equipped with:
• TYPE 1 Connector
• TYPE 2 Connector
This charging station is designed to operate with a supply voltage of 230 V 50 Hz (1P) or 400V 50Hz (3P)
PRODUCT DESCRIPTION
GENERAL
Model Name Copper Type 1 Case C Copper Type 2 Case C
Mode Mode 3 Mode 3
Overall Dimensions (w/o connector) 163x163x52 163x163x52
Weight 4-6Kg. depending on cable length 4-6Kg. depending on cable lenght
Operating Temperature -25ºC to 45ºC -25ºC to 45ºC
Storage Temperature 40ºC to 70ºC 40ºC to 70ºC
CE marking IEC61851-1, IEC61851-22 IEC61851-1, IEC61851-22
SPECIFICATIONS
Max Power 7,4kW one phase 22kW three phase
Input voltage 230V AC ± 10% 230V AC (1P), 400V AC (3P) ± 10%
Max. Current 32A, cable sizes up to 5x6mm² 32A, cable sizes up to 5x6mm²
Nominal Frequency 50Hz 50Hz
Protection Class I I
Degree of Protection IP54, indoor and outdoor IP54, indoor and outdoor
Overvoltage Category CAT III CAT III
STATUS & USER INTERFACE
Screen dimensions 4,3” 4,3”
Resolution 480x272 480x272
Communications Wi-Fi, Ethernet, Bluetooth Wi-Fi, Ethernet, Bluetooth
Authentication methods App, Face recognition, RFID, NFC App, Face recognition, RFID, NFC
MECHANICAL
Installation Wall Mount Wall Mount
Cooling Natural Cooling Natural Cooling
COPPER - installation guide
en
5
4x 6,3x40mm Screws
4x Ø8mm Wallanchors
1x Sealing RutaSeal®
4x Plugs
Mounting components:
Required tools:
Phillips head screwdriver
Torx screwdriver
Allen screwdriver
Drilling machine plus 10mm tool
Cutter or razor for the wall cable
PRODUCT DESCRIPTION
• Wallbox Copper
• Holder
• Installation Guide
• Drilling templates
The Wallbox charger components delivered must comply the following list ¹ :
¹ If any of the items described is missing, please contact
www.wallbox.com/support or service@wallbox.com
Serial Number
Product Number
Network settings
QR code
CE marking
Disposal information
1
2
3
4
5
6
1
2
3
4
5
6
COPPER - installation guide
en
6
The electrical installation of your Wallbox must be performed by a qualified electrician in accordance with the applicable
norms and standards. You must consider the local electrical installation regulations, fire prevention measures and accident
prevention regulations as well as emergency routes at this site.
PRECAUTIONS
Take special care while selecting the mounting surface, it has to be constructed in order to withstand your Wallbox weight
and the mechanical forces associated with the charging process.
The power supply connection must comply with the standards and regulations for cabling and building infrastructure.
The Wallbox device must be connected through a permanent grounded conductor of the power supply system.
Before installing or cleaning your Wallbox ensure that the power supply is turned o and the system has not energy.
Suicient air circulation must be ensured at the mounting site so that the charging station is cooled during operation:
Always observe the allowed operating temperatures of the device.
Do not install the Wallbox charger nearby:
x Flammable, explosive or combustible materials.
x Chemicals or solvents,
x Flood prone areas, water passage areas or humid environments
x Gas conductors or vapor outlets.
x Accumulators, storage radiators or heat emitting elements
x Direct Sunlight radiation, so as to avoid overheating and degradation over time.
INSTALLATION INSTRUCTIONS
Outdoors installation: The charging station should only be installed in covered locations that provide suicient
protection from rainwater. Installation in a garage or carport is recommended, as long as it fulfills the stated
requirements.
Please contact an electrician or arrange installation at your premises with your local distributor.
COPPER - installation guide
en
7
DIMENSIONS & POSITIONING
Before selecting the mounting situation of your Wallbox, please read the following tips and references:
According to the product standard, the charging station must be located at a height (y)
between 1.30 m and 1.70 m. We recommend mounting the charging station at a height of 1.60 m.
Keep in mind that national regulations can limit this height.
Its is compulsory to consider the following precautions:
• The required mounting area for the Wallbox charging station is at least 250 x 150 mm (H x W).
• When mounting the Wallbox, the cable should easily reach the charging port.
• For a safe operation of your charging station, the recommended minimum distances to other technical installations
must be observed.
• Note that when you install the support for the charger connector, you have enough space to facilitate the ergonomics.
It is advisable to have a free area around the device of 400mmmx400mm.
250
150
250
150
y
Proper installation is absolutely necessary and is beyond the scope of liability of Wallbox
COPPER - installation guide
en
8
DRILL & MOUNT
DRILLING TEMPLATE PROCEDURE
• Use the drilling template as a guide to mark the location on the wall for the mounting screws. Pay special attention
when levelling the template. The use of a spirit level is highly recommended.
• Drill the marked mounting holes with the diameter specified for the selected installation hardware and check the posi-
tioning of the holes. For installation on concrete, brick and wood walls, use the included installation hardware.
COPPER MOUNTING
Step 1: Use the selector on the cover to choose the maximum operating current of the supply connection.
BACKSIDE MOUNTING
IMPORTANT: In case your wallbox is using a backside-wall cable connection, please follow steps 0 and Step 00. If not using
such cable connection, please go to step1.
Step 0: In the backside of the wallbox charger you will find an insertion with a thinner wall; use a cutter, razor or a sharp tool
and carefully make an incision into the cable opening. Please meticulously remove all sharp edges. Take a Rutaseal bushing
and install it.
Step 00: Very carefully, firmly insert your cable supply through the bushing. Bush hole sealing is prepared for a range that
can vary from 11 to 17mm which falls within the standard for cables that can carry up to 22kW.
Make sure the power supply is turned o during all mounting steps
OPENING THE DEVICE
1. Unscrew the two screws on the bottom side of the frame
and remove it
2. Remove the 6 screws of the front cover
3 Open carefully the cover
4 Disconnect the cover communication cable.
POSITION
CURRENT (A) 00162103134165206257328090
Step 2: Proceed to fix your charger to the wall. Insert the screws in the positions marked,
starting with the top one, and continuing clockwise.
Verify that your Wallbox is firmly attached and insert the plugs to complete this process.
COPPER - installation guide
en
9
Step 5: confirm the previous four steps.
Step 6: reconnect the cover communication cable, and close the front cover
taking special care of the fitting and that the O-ring sealing remains in place.
Step 7: Screw the six screws of the cover
Step 8: Insert the frame and screw the two screws.
One Phase Configuration
From left to right:
L1 (Current-carring conductor)
N: Neutral line
:Protective Earth
The presented color connection is not
subject to an international standard,
please always check the power supply
connection
Three Phase Configuration
From left to right:
L1,L2 & L3 (Current-carring conductors)
N: Neutral line
:Protective Earth
The presented color connection is not
subject to an international standard,
please always check the power supply
connection
HOLDER MOUNTING
Step 1: Mark the location on the wall for the mounting screws.
Step 2: Drill the marked holes.
Step 3: Fix the socket to the wall. Insert the screws in the positions marked.
DRILL & MOUNT
Step 3: Insert the mains supply cable through the bushing (as pictured)
Step 4: Connect the power lines, neutral and protective earth using the terminal blocks provided
COPPER - installation guide
en
10
STARTUP
Once the DRILL & MOUNT process is completed your Wallbox is ready to operate. But first lets take a moment to read and
review some useful information before starting to use your Wallbox:
• Do not use your Wallbox for pruposes not described in the Product description chapter
• Do not open in any case the charger’s front cover while the power supply is on.
• Special precautions must be taken for medical or implantable electronics. Please contact the device manufacturer to
understand the eects that charging may have on such electronics.
• REVIEW & CONFIRM ALL THE STEPS TAKEN
TROUBLESHOOTING
MAINTENANCE
• Your network supply is continously checked to ensure a safe operation of the device. If one of the parameters is not in
range the charger will stop the power supply to the vehicle.
• Charging process uses a secure comunication protocol (called Control Pilot) between your wallbox and the vehicle. If
the car detects a problem during the charging process, it will be interrupted. At this point a message will pop up in your
status menu.
• The internal stats of the Wallbox are also being parameterized in real time. A change in the normal operating values
will lead the charger to safely disconnect the power supply to the vehicle.
Please take some precautions to ensure a correct maintenance :
• There are no parts inside your Wallbox that need to be maintained by the user. Only qualified electrician can open and
manipulate your Wallbox.
• Remeber to ensure that the power supply is turned o, before start cleaning your charger.
• In case you want to clean your Wallbox, we recommned you to use a soft, dry or damp cloth. Do not use a spray or
direct water to clean your Wallbox charger.
• It is mandatory to use the protection element or support, provided as an accessory, in order to protect the connector
from falling, dirt and other meteorological elements
WARRANTY
www.wallbox.com service@wallbox.com
At this point you can turn on the power supply and enjoy your Wallbox experience
Loading...