Wacker Neuson WP 1550, WP 1550W, WP 1550A, WP 1550AW Operator's Manual

Operator’s Manual

Vibroplate

WP 1550

WP 1550W

0155940EN

0155940en / 008

WP 1550 Table of Contents

Foreword 3

1. Safety Information 4

1.1 Laws Pertaining to Spark Arresters ...................................................... 5

1.2 Operating Safety .................................................................................. 6

1.3 Operator Safety while using Internal Combustion Engines .................. 7

1.4 Service Safety ...................................................................................... 8

1.5 Label Locations .................................................................................... 9

1.6 Warning and Informational Labels ...................................................... 10

1.7 Operating Labels ................................................................................ 13

2. Technical Data 15

2.1 Engine Data ........................................................................................ 15

2.2 Plate Data .......................................................................................... 16

2.3 Sound and Vibration Specifications .................................................... 16

2.4 Dimensions ......................................................................................... 17

3. Operation 18

3.1 Recommended Fuel ........................................................................... 18

3.2 Before Starting ................................................................................... 18

3.3 To Start ............................................................................................... 19

3.4 To Stop ............................................................................................... 19

3.5 Application .......................................................................................... 20

3.6 Operation ............................................................................................ 21

3.7 Wheel Kit (0162986) ........................................................................... 22

wc_bo0155940en_008TOC.fm 1

Table of Contents WP 1550

4. Maintenance 23

4.1 Periodic Maintenance Schedule ..........................................................23

4.2 Cleaning Plate .....................................................................................25

4.3 Drive Belt .............................................................................................25

4.4 Exciter Lubrication ...............................................................................26

4.5 Spark Plug ...........................................................................................27

4.6 Engine Oil ............................................................................................28

4.7 Air Cleaner ..........................................................................................29

4.8 Cleaning Fuel Strainer .........................................................................30

4.9 Troubleshooting ...................................................................................31

4.10 Storage ................................................................................................31

4.11 Lifting Machine ....................................................................................32

4.12 Transporting Machine ..........................................................................33

wc_bo0155940en_008TOC.fm 2

Foreword

WARNING

CALIFORNIA

Proposition 65 Warning:

Engine exhaust, some of its constituents, and certain vehicle
components, contain or emit chemicals known to the State of
California to cause cancer and birth defects or other reproductive
harm.

This manual provides information and procedures to safely operate
and maintain this Wacker Neuson model. For your own safety and
protection from injury, carefully read, understand and observe the
safety instructions described in this manual.

Keep this manual or a copy of it with the machine. If you lose this
manual or need an additional copy, please contact Wacker Neuson
Corporation. This machine is built with user safety in mind; however,
it can present hazards if improperly operated and serviced. Follow
operating instructions carefully! If you have questions about operating
or servicing this equipment, please contact Wacker Neuson
Corporation.

The information contained in this manual was based on machines in
production at the time of publication. Wacker Neuson Corporation
reserves the right to change any portion of this information without
notice.

All rights, especially copying and distribution rights, are reserved.

Copyright 2009 by Wacker Neuson Corporation.

No part of this publication may be reproduced in any form or by any
means, electronic or mechanical, including photocopying, without
express written permission from Wacker Neuson Corporation.

Any type of reproduction or distribution not authorized by Wacker
Neuson Corporation represents an infringement of valid copyrights
and will be prosecuted. We expressly reserve the right to make
technical modifications, even without due notice, which aim at
improving our machines or their safety standards.

wc_tx000001gb.fm 3

Safety Information WP 1550

1. Safety Information

This manual contains DANGER, WARNING, CAUTION, NOTICE and
NOTE callouts which must be followed to reduce the possibility of
personal injury, damage to the equipment, or improper service.

This is the safety alert symbol. It is used to alert you to potential
personal injury hazards. Obey all safety messages that follow this
symbol to avoid possible injury or death.

DANGER indicates a hazardous situation which, if not avoided, will
result in death or serious injury.

DANGER

WARNING

CAUTION

WARNING indicates a hazardous situation which, if not avoided, could
result in death or serious injury.

CAUTION indicates a hazardous situation which, if not avoided, could
result in minor or moderate injury.

NOTICE: Used without the safety alert symbol, NOTICE indicates a
situation which, if not avoided, could result in property damage.

Note: Contains additional information important to a procedure.

wpm_si000324gb.fm 4

WP 1550 Safety Information

1.1 Laws Pertaining to Spark Arresters

Notice: State Health Safety Codes and Public Resources Codes

specify that in certain locations spark arresters be used on internal
combustion engines that use hydrocarbon fuels. A spark arrester is a
device designed to prevent accidental discharge of sparks or flames
from the engine exhaust. Spark arresters are qualified and rated by
the United States Forest Service for this purpose.

In order to comply with local laws regarding spark arresters, consult
the engine distributor or the local Health and Safety Administrator.

wpm_si000324gb.fm 5

Safety Information WP 1550

1.2 Operating Safety

Familiarity and proper training are required for the safe operation of the
machine. Machines operated improperly or by untrained personnel
can be hazardous. Read the operating instructions contained in this
manual and the engine manual, and familiarize yourself with the
location and proper use of all controls. Inexperienced operators should
receive instruction from someone familiar with the machine before
being allowed to operate it.

1.2.1 Do not allow anyone to operate this equipment without proper training.
People operating this equipment must be familiar with the risks and
hazards associated with it.

1.2.2 Do not touch the engine or muffler while the engine is on or
immediately after it has been turned off. These areas get hot and may
cause burns.

1.2.3 Do not use accessories or attachments that are not recommended by
Wacker Neuson. Damage to equipment and injury to the user may
result.

1.2.4 NEVER operate the machine with the beltguard missing. Exposed
drive belt and pulleys create potentially dangerous hazards that can
cause serious injuries.

1.2.5 NEVER leave the machine running unattended.

1.2.6 Be sure operator is familiar with proper safety precautions and
operation techniques before using machine.

1.2.7 ALWAYS wear protective clothing appropriate to the job site when
operating the machine.

1.2.8 Wear hearing protection when operating equipment.

1.2.9 Close fuel valve on engines equipped with one when machine is not
being operated.

1.2.10 Store the machine properly when it is not being used. The machine
should be stored in a clean, dry location out of the reach of children.

1.2.11 Always operate machine with all safety devices and guards in place
and in working order. Do not modify or defeat safety devices. Do not
operate machine if any safety devices or guards are missing or
inoperative.

1.2.12 Read, understand, and follow procedures in the Operator’s Manual
before attempting to operate the machine.

wpm_si000324gb.fm 6

WP 1550 Safety Information

1.3 Operator Safety while using Internal Combustion Engines

Internal combustion engines present special hazards during operation
and fueling. Read and follow the warning instructions in the engine
owner’s manual and the safety guidelines below. Failure to follow the

WARNING

1.3.1 DO NOT run the machine indoors or in an enclosed area such as a

1.3.2 Do not smoke while operating the machine.

1.3.3 Do not smoke when refueling the engine.

1.3.4 Do not refuel a hot or running engine.

1.3.5 Do not refuel the engine near an open flame.

1.3.6 Do not spill fuel when refueling the engine.

1.3.7 Do not run the engine near open flames.

warnings and safety standards could result in severe injury or death.

deep trench unless adequate ventilation, through such items as
exhaust fans or hoses, is provided. Exhaust gas from the engine
contains poisonous carbon monoxide gas; exposure to carbon
monoxide can cause loss of consciousness and may lead to death.

1.3.8 Refill the fuel tank in a well-ventilated area.

1.3.9 Replace the fuel tank cap after refueling.

1.3.10 ALWAYS check the fuel lines and the fuel tank for leaks and cracks
before starting the engine. Do not run the machine if fuel leaks are
present or the fuel lines are loose.

wpm_si000324gb.fm 7

Safety Information WP 1550

1.4 Service Safety

A poorly maintained machine can become a safety hazard! In order
for the machine to operate safely and properly over a long period of
time, periodic maintenance and occasional repairs are necessary.

WARNING

1.4.1 Do not attempt to clean or service the machine while it is running.
Rotating parts can cause severe injury.

1.4.2 Do not crank a flooded engine with the spark plug removed on
gasoline-powered engines. Fuel trapped in the cylinder will squirt out
the spark plug opening.

1.4.3 Do not test for spark on gasoline-powered engines if the engine is
flooded or the smell of gasoline is present. A stray spark could ignite
the fumes.

1.4.4 Do not use gasoline or other types of fuels or flammable solvents to
clean parts, especially in enclosed areas. Fumes from fuels and
solvents can become explosive.

1.4.5 Keep the area around the muffler free of debris such as leaves, paper,
cartons, etc. A hot muffler could ignite the debris and start a fire.

1.4.6 Replace worn or damaged components with spare parts designed and
recommended by Wacker Neuson Corporation.

1.4.7 Disconnect the spark plug on machines equipped with gasoline
engines, before servicing, to avoid accidental start-up.

1.4.8 Keep the machine clean and labels legible. Replace all missing and
hard-to-read labels. Labels provide important operating instructions
and warn of dangers and hazards.

wpm_si000324gb.fm 8

WP 1550 Safety Information

1.5 Label Locations

1 2

wpm_si000324gb.fm 9

WARNING
WARNUNG

ADVERTENCIA

AVERTISSEMENT

3

4 5 6 7

10W30

wpmgr005959

1

2

Safety Information WP 1550

1.6 Warning and Informational Labels

Wacker Neuson machines use international pictorial labels where
needed. These labels are described below:

Label Meaning

WARNING!
To prevent hearing loss, wear hearing protec­tion when operating the machine.

Read the Operator’s Manual for machine infor­mation.

 9! 

Check engine oil level.
Use SAE10W30.

Check the fuel level.

WARNING!
Hot surface!

Guaranteed sound power level in dB(A).

wpm_si000324gb.fm 10

WP 1550 Safety Information

Label Meaning

WARNING!
Hand injury if caught in moving belt.
Always replace beltguard.

CAUTION!
Read and understand the supplied Operator’s
Manual before operating this machine. Failure
to do so increases the risk of injury to yourself
or others.

NOTICE
Lifting point.

Lifting point (manual).

DANGER!
Engines emit carbon monoxide; operate only
in well-ventilated area. Read the Operator’s
Manual.
No sparks, flames, or burning objects near the
machine. Shut off the engine before refueling.

Label-machine model

wpm_si000324gb.fm 11

Safety Information WP 1550

Label Meaning

Company logo

A nameplate listing the model number, item
number, revision number, and serial number is
attached to each unit. Please record the infor­mation found on this plate so it will be avail­able should the nameplate become lost or
damaged. When ordering parts or requesting
service information, you will always be asked
to specify the model number, item number,
revision number, and serial number of the unit.

This machine may be covered by one or more
patents.

wpm_si000324gb.fm 12

WP 1550 Safety Information

1.7 Operating Labels

Wacker Neuson machines use international pictorial labels where
needed. These labels are described below:

Label Meaning

Open the fuel flow valve.

Push or turn engine switch to ON position.

Close the choke.

Place throttle in the IDLE position.

Pull the rewind starter.

Close the fuel flow valve.

wpm_si000324gb.fm 13

Safety Information WP 1550

Label Meaning

1

Push or turn engine switch to OFF position.

Open the choke.

Place throttle in the FAST position.

Throttle control lever:
Turtle = Idle or Slow
Rabbit = Full or Fast

wpm_si000324gb.fm 14

WP 1550 Technical Data

2. Technical Data

2.1 Engine Data

Engine Power Rating

Net power rating per SAE J1349. Actual power output may vary due to
conditions of specific use.

WP 1550, WP 1550 W

0009325, 0009324, 0009548

Engine

Engine Make Wacker
Engine Model WM170
Max. rated power @

rated speed
Operating speed
Clutch Engagement
Spark Plug
Electrode Gap
Air Cleaner
Engine Lubrication

Engine Oil Capacity
Fuel
Fuel Tank Capactity
Valve Clearance (cold)

Inlet:
Outlet:

kW (Hp)

rpm

rpm

type

mm (in)

type

oil grade

service class

ml (oz.)

type

l (qts.)

mm (in.)

4.2 (5.7)

@ 4000 rpm

3600
2100

NGK BR6HS, Champion RL86C

0.6–0.7 (0.024–0.028)
Dual Element

SAE 10W30

SE or higher

600 (20)

Regular unleaded gasoline

3.6 (3.8)

0.07–0.13 (0.003–0.005)

0.17–0.23 (0.007–0.009)

wpm_td000333gb.fm 15

Technical Data WP 1550

2.2 Plate Data

WP 1550, WP 1550 W

0009325, 0009324, 0009548

Plate

Operating Weight
Water Tank Capacity
Exciter Speed
Exciter Lubrication

kg (lbs.)

l (qts.)

rpm / belt

ml (oz.)

2.3 Sound and Vibration Specifications

Products are tested for sound pressure level in accordance with EN
ISO 11204. Sound power level is tested in accordance with European
Directive 2000/14/EC - Noise Emission in the Environment by
Equipment for use outdoors.

• The sound pressure level at operator’s location (LpA) = 97 dB(A).

• The guaranteed sound power level (LWA) = 108 dB(A).
Products are tested for hand/arm vibration (HAV) level in accordance

with ISO 5349, EN1033, and EN500-4 where applicable.

88 (194)

10.4 (11.0)

5800 ± 100

150 (5)

Automatic Transmission Fluid

Dextron III / Mercon or equivalent

• HAV 10.8 m/s

2

wpm_td000333gb.fm 16

WP 1550 Technical Data

2.4 Dimensions

mm (in.)

38 (965)

19.5 (500)

34.5 (875)

wpmgr005986

wpm_td000333gb.fm 17

Operation WP 1550

3. Operation

3.1 Recommended Fuel

The engine requires regular grade unleaded gasoline. Use only fresh,
clean gasoline. Gasoline containing water or dirt will damage fuel
system. Consult engine owner’s manual for complete fuel
specifications.

3.2 Before Starting

3.2.1 Read and understand the safety and operating instructions at the
beginning of this manual.

3.2.2 Check:

• Oil level in the engine

• Fuel level

• Condition of the air cleaner

• Tightness of the external fasteners

• Condition of the fuel lines

wpm_tx001125gb.fm 18

WP 1550 Operation

3.3 To Start

See Graphic: wc_gr000655

3.3.1 Open fuel valve by moving lever down (a1).

Note: If engine is cold, move choke lever to close position (d2). If
engine is hot, set choke to open position (d1).

3.3.2 Turn engine switch to “ON” (b2).

3.3.3 Open throttle by moving it slightly to left (c2).

3.3.4 Pull starter rope (e).

Note: If the oil level in the engine is low, the engine will not start. If this
happens, add oil to engine.

3.3.5 Open choke as engine warms (d1).

3.3.6 Open throttle fully to operate (c1).

a2

a1

d2

3.4 To Stop

See Graphic: wc_gr000655

d1

b2

b1

e

c1

wc_gr000655

c2

c3

3.4.1 Reduce engine RPM to idle by moving throttle completely to right (c3).

3.4.2 Turn engine switch to “OFF” (b1).

3.4.3 Close fuel valve (a2).

wpm_tx001125gb.fm 19

Operation WP 1550

3.5 Application

This plate is designed for compacting loose, granular soils, gravel, and
paving stones. It is intended to be used in confined areas and areas
next to structures such as walls, curbs, and foundations. Plates
equipped with water tanks can be used for compacting asphalt.

This plate is not recommended for compacting cohesive soils with a
heavy clay content. For cohesive soil, use a vibratory rammer or
sheepsfoot roller.

wpm_tx001125gb.fm 20

WP 1550 Operation

3.6 Operation

See Graphic: wpmgr006016

Run engine at full throttle and allow plate to pull itself along at its
normal speed. When operating on an incline it may be necessary to
assist plate by pushing it forward slightly. Depending on the material
being compacted, three or four passes are recommended to achieve
the best compaction.

While a certain amount of moisture in the soil is necessary, excessive
moisture may cause soil particles to stick together and prevent good
compaction. If soil is extremely wet, allow it to dry somewhat before
compacting.

If soil is so dry as to create dust clouds while operating plate, some
moisture should be added to the ground material to improve
compaction. This will also reduce service to the air filter.

For compacting asphalt, open water tank valve (a1) to wet asphalt and
underside of plate. This will prevent asphalt material from sticking. Two
or three passes are usually sufficent to ensure good compaction.

When using plate on paving stones, attach a pad to the bottom of the
plate to prevent chipping or grinding surface of the stones. A special
urethane pad designed for this purpose is available as an optional
accessory.

NOTICE: DO NOT operate plate on concrete or on extremely hard,
dry, compacted surfaces. The plate will jump rather than vibrate and
could damage both plate and engine.

wpm_tx001125gb.fm 21

wpmgr006016

Operation WP 1550

3.7 Wheel Kit (0162986)

See Graphic: wc_gr002793

Wheel kit (Part No. 0162986) is a standard item on Item Number
0009545, 0009546, 0009547 and 0009548 only. Available as an
option on all other models.

3.7.1 Disengage wheel kit from holding latch (a) and position wheels in
“down” position.

3.7.2 Pivot holding latch and engage cross member brace into latch.
NOTICE: Latch prevents vibroplate from pivoting and falling back

towards the operator.

3.7.3 Push forward on guide handle to tip vibroplate forward and pivot
wheels into the “down” position.

3.7.4 Pull back on guide handle to tip vibroplate back up on wheels to
transport.

NOTICE: DO NOT lift the vibroplate by its guide handle. The vibroplate
can shift, causing it to fall.

wpm_tx001125gb.fm 22

a

a

wc_gr002793

WP 1550 Maintenance

4. Maintenance

4.1 Periodic Maintenance Schedule

4.1.1 Engine Maintenance

The chart below lists basic engine maintenance. Refer to the engine
manufacturer’s Operation Manual for additional information.

Check fuel level.
Check engine oil level.
Inspect fuel lines.
Inspect air filter. Replace as needed.
Clean air cleaner elements.
Change engine oil.
Clean engine cooling fins.
Clean sediment cup / fuel filter.
Check and clean spark plug.
Check and adjust valve clearance.
Change exciter oil.

Daily

before

starting









After

first

20 hrs.



Every

2 weeks

or

50 hrs.



Every

month

or

100 hrs.







Every

year

or

300 hrs.





wpm_tx001126gb.fm 23

Maintenance WP 1550

4.1.2 Machine Maintenance

The chart below lists basic machine maintenance.

Check external hardware.
Check and adjust drive belt.
Inspect shockmounts for damage.
Replace shockmounts as needed.
Change exciter oil.

Note: When machine is being used in asphalt, it is highly
recommended that shockmounts are replaced every year or
after 300 hours of usage.

Daily

before

starting



After

first

20 hrs.



Every

2 weeks

or

50 hrs.



Every

month

or

100 hrs.

Every

year

or

300 hrs.





wpm_tx001126gb.fm 24

WP 1550 Maintenance

7

4.2 Cleaning Plate

Clean plate after use to remove dirt, stones, and mud caught under the
engine console. If plate is being used in a dusty area, check engine
cylinder cooling fins for heavy dirt accumulation. Keep engine cylinder
fins clean to prevent engine from overheating.

4.3 Drive Belt

See Graphic: wc_gr000077

On new machines or after installing a new belt, check belt tension after
first 20 hours of operation. Check and adjust belt every 50 hours
thereafter.

To change the belt:

4.3.1 Remove the beltguard and remove the four hex nuts (a) holding pulley
halves (b) together. Remove outer pulley half and remove belt.

4.3.2 Install new belt on pulley and secure pulley halves together with hex
nuts. Adjust tension on belt by adding or removing spacers (c)
between pulley halves. The fewer spacers used between pulley
halves, the tighter the belt will be. Three spacers with new Wacker
belts should provide the correct tension. Belt deflection should be 6–
10 mm, checked half way between the clutch pulley and the exciter
pulley (d). Place unused spacers on outside of pulley.

4.3.3 Replace beltguard.

@

>

?

=

w c _ g r 0 0 0 0 7

wpm_tx001126gb.fm 25

Maintenance WP 1550

4.4 Exciter Lubrication

See Graphic: wpmgr006021

The exciter assembly is a self-contained, sealed unit. The bearings are
lubricated using automatic transmission fluid (see Technical Data for
type). Change fluid once every year or 300 hours of operation. When
changing fluid, replace O-ring (a).

To change fluid:

4.4.1 Remove beltguard, belt, and hose from water tank.

4.4.2 Remove four screws (b) securing console assembly to baseplate and

lift console assembly from baseplate.

4.4.3 Remove end cover (c) from bearing exciter assembly. Outer bearing

race will remain with cover.

4.4.4 Tip baseplate up and drain fluid from exciter assembly. Dispose of
used fluid in an appropriate manner. Contact local recycling center.

4.4.5 Add 150 ml of automatic transmission fluid to exciter housing and
fasten end cover to exciter. Do not overfill exciter or bearings may
overheat.

4.4.6 Assemble console assembly to baseplate and install belt, beltguard,
and hose to water tank.

wpm_tx001126gb.fm 26

wpmgr006021

WP 1550 Maintenance

4.5 Spark Plug

See Graphic: wc_gr000028

Clean or replace the spark plug as needed to ensure proper operation.
Refer to your engine operator’s manual.

The muffler becomes very hot during operation and remains hot for a
while after stopping the engine. Do not touch the muffler while it is hot.

WARNING

Note: Refer to section “Technical Data” for the recommended spark

plug type and the electrode gap setting.

4.5.1 Remove the spark plug and inspect it.

4.5.2 Replace the spark plug if the insulator is cracked or chipped.

4.5.3 Clean the spark plug electrodes with a wire brush.

4.5.4 Set the electrode gap (a).

4.5.5 Tighten the spark plug securely.

NOTICE: A loose spark plug can become very hot and may cause
engine damage.

wpm_tx001126gb.fm 27

Maintenance WP 1550

4.6 Engine Oil

See Graphic: wc_gr000087

4.6.1 Drain oil while engine is still warm.

Note: In the interests of environmental protection, place a plastic sheet
and a container under the machine to collect any liquid which drains
off. Dispose of this liquid in accordance with environmental protection
legislation.

4.6.2 Remove the oil drain plug (a).

4.6.3 Allow the oil to drain.

4.6.4 Install the drain plug.

4.6.5 Fill the engine crankcase through the oil filler opening (b), to the upper
mark on the dipstick (c). Do not thread in the dipstick to check the level.
See Technical Data for oil quantity and type.

4.6.6 When the crankcase is full, reinstall the dipstick.

?

>
=

w c _ g r 0 0 0 0 8 7

wpm_tx001126gb.fm 28

WP 1550 Maintenance

4.7 Air Cleaner

See Graphic: wc_gr000656

NEVER use gasoline or other types of low-flash point solvents for
cleaning the air cleaner. A fire or explosion could result.

WARNING

NOTICE: NEVER run the engine without the air cleaner. Severe
engine damage will occur.

The engine is equipped with a dual-element air cleaner. Under normal
operating conditions, the elements should be cleaned once every
week. Under severe, dry and dusty conditions, the elements should be
maintained daily. Replace an element when it is saturated with dirt that
cannot be removed.

4.7.1 Remove the air cleaner cover (a). Remove the filter assembly by

pulling it straight up. Inspect both elements for holes or tears. Replace
damaged elements.

4.7.2 Wash the foam element (b) in a solution of mild detergent and warm

water. Rinse it thoroughly in clean water. Allow the element to dry
thoroughly.

4.7.3 Tap the paper element (c) lightly to remove excess dirt or blow

compressed air through the filter from the inside out. Replace the
paper element if it appears heavily soiled.

a

b

c

wpm_tx001126gb.fm 29

wc_gr000656

Maintenance WP 1550

4.8 Cleaning Fuel Strainer

See Graphic: wc_gr001093

4.8.1 To remove water and dirt, close the fuel lever and remove the fuel
strainer.

4.8.2 Inspect the fuel strainer (a) for water and dirt.

4.8.3 After removing any dirt and water, wash the fuel cup with a
nonflammable solvent.

4.8.4 Reinstall securely to prevent leakage.

wpm_tx001126gb.fm 30

WP 1550 Maintenance

4.9 Troubleshooting

Problem / Symptom Reason / Remedy

Plate does not develop full

speed. Poor compaction.

• Engine throttle control not completely open.

• Throttle control not adjusted correctly.

• Ground too wet, plate sticking. Allow soil to dry
before compacting.

• Drive belt loose or worn, slipping on pulleys. Adjust
or replace belt. Check that engine mounting bolts
are tight.

• Exciter bearings binding. Check condition and level
of oil in exciter. Add or change oil.

• Air filter clogged with dust, reducing engine perfor­mance. Clean or replace air filter.

• Engine speed too low. Check engine speed with
tachometer. Adjust or repair engine to run at correct
speed. Refer to engine manual.

Engine running, no vibration • Engine throttle not open.

• Drive belt loose or broken. Adjust or replace.

• Clutch damaged. Inspect and replace clutch.

Plate jumps or compacts

unevenly.

4.10 Storage

If plate is being stored for more than 30 days:

4.10.1 Remove loose stones and dirt from plate.

4.10.2 Clean engine cylinder cooling fins.

4.10.3 Clean or replace air filter.

4.10.4 Change exciter oil.

4.10.5 Change engine oil and follow procedures described in engine manual
for engine storage.

4.10.6 Cover plate and engine and store in a clean, dry area.

• Engine speed too low. Check engine speed.

• Too much oil in exciter. Adjust oil to correct level.

• Ground surface too hard.

• Shockmounts loose or damaged.

wpm_tx001126gb.fm 31

Maintenance WP 1550

4.11 Lifting Machine

See Graphic: wpmgr006037

See Technical Data for the weight of the machine.

To lift machine manually:

4.11.1 Stop the engine.

4.11.2 Obtain help from a partner and plan the lift.

4.11.3 Grasp the machine by its cage (a) and lifting slot (b).

4.11.4 Lift the machine as shown.
To reduce risk of back injury while lifting, keep your feet flat on ground

and shoulder width apart. Keep your head up and back straight.

WARNING

To lift machine mechanically:

NOTICE: Before attempting to lift, be sure that all lifting devices can
safely handle the weight of the machine. See Technical Data for the
weight of the machine.

4.11.1 Attach hook, harness, or cable to the machine as shown and lift as
desired.

NOTICE: DO NOT lift the vibroplate by its guide handle. The vibroplate
can shift, causing it to fall.

a

wpm_tx001126gb.fm 32

b

wpmgr006037

WP 1550 Maintenance

4.12 Transporting Machine

See Graphic: wpmgr006055

To avoid burns or fire hazards, let engine cool before transporting
machine or storing indoors.

WARNING

4.12.1 Turn fuel valve to the off position and keep the engine level to prevent
fuel from spilling.

4.12.2 Tie down machine on vehicle to prevent machine from sliding or tipping
over. Tie machine to vehicle at points shown on graphic.

wpm_tx001126gb.fm 33

wpmgr006055

EC DECLARATION OF CONFORMITY

EG-KONFORMITÄTSERKLÄRUNG

CE-DECLARACIÓN DE CONFORMIDAD

DÉCLARATION DE CONFORMITÉ DE LA CEE

WACKER NEUSON MANILA, INC., DASMARIÑAS, CAVITE, PHILIPPINES

AUTHORIZED REPRESENTATIVE IN THE EUROPEAN UNION
BEVOLLMÄCHTIGTER VERTRETER FÜR DIE EUROPÄISCHE GEMEINSCHAFT
REPRESENTANTE AUTORIZADO EN LA UNIÓN EUROPEA
REPRÉSENTANT AGRÉÉ AUPRÈS DE L’UNION EUROPÉENNE

hereby certifies that the construction equipment specified hereunder / bescheinigt, daß das Baugerät / certifica que la máquina de
construcción / atteste que le matériel :

1. Category / Art / Categoría / Catégorie

WACKER NEUSON SE
Preußenstraße 41
80809 München

Vibratory Plates / Rüttelplatten

Planchas Vibratorias / Plaques Vibrantes

2. Type - Typ - Tipo - Type

WP 1550A, WP 1550AW

WP 1550, WP 1550W

3. Item number of equipment / Artikelnummer / Número de referencia de la máquina / Numéro de référence du matériel :

4. Net installed power / absolute installierte Leistung / Potencia instalada neta / Puissance installée nette :

WP 1550A, WP 1550AW 3,6kW

0007579, 0007576, 0009486, 0009325, 0009324, 0009546, 0009548

WP 1550, WP 1550W 4,2kW

Has been sound tested per Directive 2000/14/EC / In Übereinstimmung mit Richtlinie 2000/14/EG bewertet worden ist / Ha sido
ensayado en conformidad con la norma 2000/14/CE / A été mis à l’épreuve conforme aux dispositions de la directive 2000/14/CEE :

Conformity Assessment Procedure
/ Konformitätsbewertungsverfahren
/ Procedimiento para ensayar
conformidad / Procédé pour
l’épreuve de conformité

Annex VI / Anhang VI /

Anexo VI / Annexe VI

and has been produced in accordance with the following standards / und in Übereinstimmung mit folgenden Richtlinien hergestellt
worden ist / y ha sido fabricado en conformidad con las siguientes normas / et a été produit conforme aux dispositions des directives
européennes ci-après :

Name and address of notified
body / Bei folgender
einbezogener Prüfstelle /
Oficina matriculadora /
Organisme agrée

VDE-Prüf- und

Zertifizierungsinstitut

Zertifizierungsstelle

Merianstraße 28

63069 Offenbach/Main

Measured sound power level /
Gemessener Schallleistungspegel
/ Nivel de potencia acústica
determinado / Niveau de puissance
acoustique fixé

WP 1550A 104 dB(A)

WP 1550AW 104 dB(A)

WP 1550 104 dB(A)

WP 1550W 104 dB(A)

Guaranteed sound power level /
Garantierter Schallleistungspegel /
Nivel de potencia acústica
garantizado / Niveau de puissance
acoustique garanti

WP 1550A 108 dB(A)

WP 1550AW 108 dB(A)

WP 1550 108 dB(A)

WP 1550W 108 dB(A)

2000/14/EG
98/37/EG
89/336/EG
EN 500-1
EN 500-4

Date / Datum / Fecha / Date

WP1550-Q_2009_WN.fm

22.01.09

WACKER NEUSON MANILA, INC.

Heinz Gengnagel
President & CEO

Wacker Construction Equipment AG · Preußenstraße 41 · D-80809 München · Tel.: [phone] - 0 · Fax: +49 - (0)89-3 54 02-3 90

Neuson Corporation · P.O. Box 9007 · Menomonee Falls, WI 53052-9007 · Tel. : [phone] · Fax: [phone] · Tel. : [phone]

Wacker
Wacker Asia Pacific Operations · Skyline Tower, Suite 2303, 23/F · 39 Wang Kwong Road, Kowloon Bay, Hong Kong · Tel. [phone] · Fax: [phone]