WABCO SMARTBOARD Driver Manual

SMARTBOARD

DRIVER MANUAL

2

INTRODUCTION

Monitoring a wide range of trailer functions is important for improving the performance of

haulage company operations and reducing the costs of the vehicle eet.

The SmartBoard provides a wide range of functions that can be accessed via symbols from the

main menu. The chapters below describe the various functions.

The following rules apply:

• If a system is not available and no information can be retrieved from it, the corresponding

menu symbol is not displayed.

• When the vehicle is at a standstill, the values that were last saved are displayed.

• These may deviate from the actual values (e.g. the tire pressure if a leak is present)

SMARTBOAD DRIVER MANUAL

OPERATING
INSTRUCTION

Button - Function

Selection of next menu item
or next option

Conrmation and / or execution

of the currently selected function

Back one menu level /

or save settings

Messages

Signal lamp ashing: Check current message

Driver Manual

Icon Function Display Description Options

Similar
to
Smart­Board
icons

Name and / or

description of the
function

Description of the
information or function
you see on left display

The displayed

buttons / functions

are available for the
left display

3

TABLE OF CONTENT

Function Short Description Page

Air Suspension Operating status of the Air Suspension e.g. lifting and lowering

of vehicle body and lift axle

4

Load Monitoring Display of current axle loads

7

Mileage Counter Display of mileage and trip data

8

Messages Display of diagnostic and system messages. Check this menu

when the signal lamp ashes

8

Steering Axle Lock Lock / Unlock steering axle

8

Lining Wear Status display for the brake linings

9

SafeStart Enable / Disable automatic brake in the case of unsafe driving

conditions

9

Bounce Control Smooth release of brake to avoid bouncing caused by bogie

tension

9

Brake Release Release service brake while the vehicle is at a standstill

10

GIO Function 1 & 2 Freely congurable user functions

10

Tire Monitoring Display of tire information such as current tire pressure and

nominal pressure

10

Finisher Brake Set target braking pressure for road nishers

10

Vehicle Inclination Display of inclination angle of the trailer

11

Electronic Park Brake Enable / Disable Electronic Park Brake

11

Immobilizer Lock / Unlock trailer brakes with a PIN

12

(Immobilizer)
Emergency Release

Emergency release for trailers locked by Immobilizer

12

Actual Trailer Length Display of actual trailer length

12

Language Change language

13

Extras System information and settings

13

Codes Of Messages Short Description Page

Component: TEBS D System messages of TEBS D

16

Component: TEBS E

(TEBS D/E)

System messages of TEBS E

16

Component IVTM System messages of IVTM / OptiTire

TM

18

Type of fault

18

TABLE OF CONTENT

4

AIR SUSPENSION MENU

Air Suspension Menu

Function Display Description Options

Operating status of Air
Suspension Menu

Air suspension menu:
the selected function is

highlighted with a black

box and the name is
displayed in the middle of
the menu

Select next

function

Select function /

activate function

Select previous

function
Dashed box: Activated
function
Flashing: Deactivated
function

Select next

function

Select function /

deactivate function

Select previous

function

Go back to main menu:

Select the arrow

Go back to main

menu

Air Suspension Functions

Function Display Description Options

Up & Down Lifting and lowering of

entire vehicle body

Lift vehicle

Lower vehicle

Stop*

Front

Up & Down

Lifting and lowering of
2-point drawbar trailer

Lift front axle

Lower front axle

Stop*

Rear
Up & Down

Lifting and lowering of
2-point drawbar trailer

Lift rear axle

Lower rear axle

Stop*

Left Up & Down Lifting and lowering of

2-point semi-trailer

Lift left side

Lower left side

Stop*

* Only if dead-man’s function is deactivated in parameterization

5

AIR SUSPENSION FUNCTIONS

Function Display Description Options

Right
Up & Down

Lifting and lowering of
2-point semi-trailer

Lift right side

Lower right side

Stop*

Request

Driving Level

Lifting / Lowering to (pre-)

selected driving level

Start lifting /

lowering

Vehicle is lifting / lowering

Stop lifting/

lowering

Change Driving
Level

Select available Driving

Level.

Menu will be displayed
only if more than
one Driving Level is
parameterized

Select next level

Apply level

Unloading

Level

See in menu if function is

active (dashed box) or not

Disable
unloading switch
(function will not be
started if switch is

active)

Lift Axle

Up & Down

The axle is lowered

Lift axle
(lift axle one will
always be lifted

before lift axle two)

The axle is lifted

Lower axle
(lift axle two will
always be lowered

before lift axle one)

Lift Axle OFF Lift axle one and two are

enabled

Select lift axle

Disable lift axle
(lift axle stays
permanently

lowered)

Lift axle one is disabled

Select lift axle
one

Enable lift axle
(lift axle can be lifted

by lift axle functions)

* Only if dead-man’s function is deactivated in parameterization

6

AIR SUSPENSION FUNCTIONS

Function Display Description Options

Traction Help Traction Help automatic

mode is activated

Disable Traction
Help automatic
mode

Traction Help is
deactivated

Start Traction
Help

Traction Help automatic
mode is deactivated

Enable Traction
Help automatic
mode

Traction Help is activated

Stop Traction
Help

OptiTurn™ OptiTurn™ automatic

mode is enabled

Disable
OptiTurn™
automatic mode

OptiTurn™ is off

Start OptiTurn™

OptiTurn™ automatic
mode is disabled

Enable
OptiTurn™
automatic mode

OptiTurn™ is on

Stop OptiTurn™

OptiLoad™ OptiLoad™ automatic

mode is enabled

Disable
OptiLoad™
automatic mode

OptiLoad™ function is off

Start OptiLoad™

OptiLoad™ automatic
mode is disabled

Enable
OptiLoad™
automatic mode

OptiLoad™ function is on

Stop OptiLoad™

Memory Level
1

Set and save Memory
Level 1

Request

Memory Level 1

Press > 5s to
store current level as
Memory Level 1

Vehicle is lifting / lowering

Stop

7

AIR SUSPENSION FUNCTIONS

Function Display Description Options

Memory Level
2

Set and save Memory
Level 2

Request

Memory Level 2

Press > 5s to
store current level as
Memory Level 2

Vehicle is lifting / lowering

Stop

Automatic
Level Control

Disable level control
when at a standstill

Disable
temporary

Press > 5s to
disable permanently

Forklift Control Forklift Control is disabled

Enable 2nd lift
axle characteristic
(due to attached

forklifter)

Forklift Control is enabled

Disable 2nd lift
axle characteristic
(due to attached

forklifter)

Season
Traction Help

Season mode is off

Enable Season
Traction Help
function

Date displays range of

the "season" (DD.MM to
DD.MM)*

Season mode is on

Disable Season
Traction Help
function

Date displays range of

the "season" (DD.MM to
DD.MM)*

* Date is only available when the SmartBoard has an internal battery and it is parameterized in modulator.

Load Monitoring

Function Display Description Options

Display of current axle
loads

Display of current axle
loads

Go to next axle

8

MILEAGE COUNTER

Mileage Counter

Function Display Description Options

Display of mileage
and trip data

Odometer Displays mileage

recorded by
SmartBoard

Go to next

item

Mileage Displays mileage

recorded by EBS

Go to next

item

Trip EBS Displays trip

mileage counter
EBS

Go to next

item

Trip Displays trip

mileage counter
SmartBoard

Go to next

item

Messages

Function Display Description Options

Display of diagnostic
and system messages

Displays current active
system messages and

components.

Displays the status of the
warning lamp

Go to next

message

System messages See: Codes of Messages page 16 and following

Steering Axle Lock

Function Display Description Options

Lock / Unlock steering

axle

Steering Axle Lock is

deactivated, axle is
released

Enable steering

axle lock

Steering Axle Lock is
activated, axle is locked

Disable
automatic function for
steering axle

9

LINING WEAR

Lining Wear

Function Display Description

Status display for

brake linings

All brake linings have a sufcient thickness and

are OK

At least one brake lining has reached a wear
limit. Please contact a workshop

SafeStart

Function Display Description Options

Enable / Disable
automatic brake in

case of unsafe driving
condition
(overruling the

functional switch)

The brake is applied

(function was activated by

switch)

Release
SafeStart brake
(parking brake has to
be applied before)

The brake is released

Apply SafeStart

brake (parking brake

has to be applied

before)

Bounce Control

Function Display Description Options

Smooth release

of brake to avoid

bouncing caused by
bogie tension

Bounce Control function
is deactivated

Activate Bounce
Control - only

possible if park brake

is engaged

Bounce Control function
is active

Deactivate
Bounce Control

10

BRAKE RELEASE

Brake Release

Function Display Description Options

Conrm total release
of brake

Mind all safety

precautions!

Safety function. User

has to mind all safety
precautions

Release brake

GIO Function 1 & 2

Function Display* Description Options

Enable / Disable

customer function 1

(/ 2)

Display and control options depend on customized function.

For information about GIO functions, please contact your WABCO service partner.

Tire Monitoring

Function Display Description Options

Display of tire
pressure information

Displays the current and
nominal tire pressure from

IVTM / OptiTireTM system

Go to next tire
pressure

Finisher Brake

Function Display Description Options

Finisher Brake Finisher Brake is

deactivated

Enable Finisher

Brake

Switch to brake

pressure mode

Finisher Brake is

activated

Disable Finisher

Brake

Switch to brake

pressure mode

Finisher Brake

Setting brake pressure in
steps of 0.1 bar

Increase brake

pressure

Decrease brake

pressure

11

VEHICLE INCLINATION

Vehicle Inclination

Function Display Description

Display of inclination
of the trailer

Displays current Vehicle Inclination and max.

allowed Vehicle Inclination

A ashing attention symbol warns if the current

is above max value

Electronic Park Brake

Function Display Description Options

Activate and
deactivate Electronic

Park Brake

Park brake is deactivated

either temporary or
permanently

Activate park

brake

Park brake is activated

(display during sleep

mode)

-

Brake has to be applied

to prevent rolling away

-

Park brake is activated

Deactivate park

brake permanently

Deactivate park

brake temporarily

12

IMMOBILIZER

Immobilizer

Function Display Description Options

Lock / Unlock trailer
brakes with a PIN

The trailer wheels are

unlocked. Lock trailer by

entering PIN

Select numbers

0 ... 9

Go to next digit

position

Conrmation of

input

Optional: engage parking
brake before release

-

The trailer wheels are

locked. Unlock trailer by

entering PIN

Select numbers

0 ... 9

Go to next digit

position

Conrmation of

input

Set new PIN See Settings: Set new PIN page 15

(Immobilizer) Emergency Release

Function Display Description Options

Emergency function
for Immobilizer

Allows up to 3 times
to temporary release

the brake even when
Immobilizer is activated.

As soon as vehicle
stops, Immobilizer will be

activated again.
Remaining releases are
displayed. Function is

active while Immobilizer

is locked

Conrm

emergency release

Actual Trailer Length

Function Display Description

Display of Actual
Trailer Length

Displays the Actual Trailer Length

(e.g. from extendable wood trailers)

13

LANGUAGE

Language

Function Display Description Options

Select language
out of the available
languages*

The current language is
English

Go to next
language

Select language

*Available languages depend on language package.

Extras Menu

Function Display Description Options

Operating status of
Extras Menu

System information and
settings can be displayed

and/or changed

Select function

Extras Functions

Function Display Description Options

TEBS
Data

Trailer Info
Display

Displays sensor data

of trailer, e.g. voltages,
supply pressure, braking

pressure and bellow
pressure

-

ODR Data

Displays the recorded
board data

Go to next item

Parameter
Memory

Read parameters from

modulator

Select item

Go to next item

Select

System
Info

System

Displays the system
information of modulator
and IVTM, such as part
number, software version,
serial number, production
date and Vehicle

Identication Number
(VIN)

Go to next item

IVTM

Displays the ID of an
IVTM sensor wheel
module

Go to next wheel

module

14

EXTRAS FUNCTIONS

Function Display Description Options

System
Info

Smart­Board

Displays the system
information from
SmartBoard, such as
battery status, part
number and software
version

-

Settings

Units

Toggle between metric /

imperial System

Go to next item

Select system

Splash
Image

Change display duration
(time of the start screen

displays after turning on)

Go to next item

Change time in

seconds

Toggle screen saver On

/ Off

Go to next item

Select On or Off

Set time without activity

Go to next item

Change time in

seconds

Load

Set warning level for load
and set overload level

Jump to next

digit position

Select numbers

0 ... 9

Conrmation of

input

Main
Menu
Order

Change the main menu
order

Go to next item

Select menu

item to be moved

Move item

Conrm new

item order

Save new order

15

EXTRAS FUNCTIONS

Function Display Description Options

Settings

Set new
PIN
(For Im-

mobilizer)

> Set PIN by old PIN.

New PIN setting by using
old PIN for Immobilizer
(see Immobilizer page

12 )

Go to next digit

position

Select numbers

0 ... 9

Conrmation of

input when all digits

are lled in

> Set PIN by PUK.

New PIN setting by using

PUK for Immobilizer (see
Immobilizer page 12)

Go to next digit

position

Select numbers

0 ... 9

Conrmation of

input when all digits

are lled in

Notes

16

Code Message

Component: TEBS D

007 Trailer modulator
010 EBS (ABS) relay valve
058 Trailer modulator
059 Trailer modulator
061 EBS relay valve
062 EBS relay valve / Pressure sensor
081 Pneumatic control line

083 Supply pressure sensor

084…
086

Electrical switching output

221 Trailer modulator / Sensor power

supply 24 V

232 Trailer modulator / Sensor power

supply 5 V

246 EBS-Trailer brake valve / Switch

Component: TEBS E (TEBS D/E)

001 Wheel sensor a (TEBS D/E)
002 Wheel sensor b (TEBS D/E)
003 Wheel sensor c (TEBS D/E)
004 Wheel sensor d (TEBS D/E)
005 Wheel sensor e (TEBS D/E)
006 Wheel sensor f (TEBS D/E)
007 EBS (ABS) relay valve / Solenoid

valve control (TEBS E)

009 Trailer modulator / Solenoid valve

control (TEBS D/E)

010 Trailer modulator / Solenoid control
058 EBS relay valve / Redundancy
059 EBS relay valve / Pressure sensor
061 Trailer modulator / Redundancy
062 Trailer modulator / Pressure sensors
069 Axle load sensor internal (TEBS D/E)
075 Wear sensor (TEBS D/E)
076 Failure of target value selection /

redundant braking (TEBS D/E)

Code Message

077 Desired pressure sensor internal

(TEBS D/E)

078 Desired pressure sensor external

(TEBS D/E)

080 Demand pressure sensor internal
081 Brake pressure sensor (axle c-d)
082 Switch 1 for Trailer Length
083 Switch 2 for Trailer Length
084 Switch 3 for Trailer Length
085 Switch 4 for Trailer Length
086 Switch for overload indication
088 Lateral acceleration sensor (TEBS

D/E)

089 Proximity switch
090 Freely congurable function 8
091 Freely congurable function 7
092 Freely congurable function 6
093 Freely congurable function 5
094 Freely congurable function 4
095 Freely congurable function 3
096 Freely congurable function 2
097 Freely congurable function 1
099 IN/OUT port
100 GIO-Freely congurable analogue

function

101 GIO-Freely congurable digital

function
102 Slot GIO 5
103 Slot GIO 4
104 Slot GIO 3
105 Slot GIO 2
106 Slot GIO 1
107 Slot GIO 6
108 Slot GIO 7
109 ABS sensor / Memory bit
110 Slot Subsystems
111 Button Bounce Control

CODES OF MESSAGES

CODES OF MESSAGES

See also: Hints page 19

Example: Display in 1. Numeric block: 2. Numeric block:

SmartBoard Component Type of fault
Code 001 07 001 – Wheel sensor a 07 – Distance too big

17

Code Message

112 Switch “Automatic lowering of the

lifting axle”
113 SmartBoard
114 Diagnostics power supply
115 Telematics
116 IVTM
117 ECAS Remote-Control Unit / Box
118 Axle load sensor external (axle c-d)
119 Axle load sensor external (axle e-f)
120 Distance sensor axle load (axle c-d)
121 Distance sensor axle load (axle e-f)
122 Freely programmable Function 3
123 Freely programmable Function 2
124 Freely programmable Function 1
125 Switch unloading level
126 Output speed signal
127 Distance sensor 2 (axle e-f)
128 Distance sensor 1 (axle c-d)

129 ECAS valve block
130 Output continuous positive voltage 2
131 Output continuous positive voltage 1
132 Output RSS active signal
133 Output ABS active signal
134 Finisher Brake
135 Not used
136 LIN Bus
137 Speed switch 2 (ISS 2)
138 Speed switch 1 (ISS 1) for

manoeuvring aid
139 Valve residual pressure maintenance
140 Valve residual pressure maintenance

for Traction Help
141 Lifting axle valve 2
142 Lifting axle valve 1
143 Pneumatic control line

144 Supply pressure sensor
145 External ELM
146 External ECAS
148 Internal ECAS / Calibration
156 Not used
157 Switch normal level 2
158 Switch Up
159 Switch Down
160 Brake release function
163 Axle load calibration
164 Not used
165 Trailer Length Proximity switch 1
167 Output Steering Axle Lock

Code Message

168 Switch Output Steering Axle Lock
169 Immobilizer PIN invalid
170 Output tilt warning
178 Valve Immobilizer
179 Buzzer Immobilizer
180 Demand pressure at Router/Repeater
181 Router / Repeater power supply to

local system

182 Router / Repeater power supply to

following system

183 Router / Repeater CAN to local

system

184 Router / Repeater CAN to following

system
185 ECAS deactivation switch
186 Normal level 4 switch
187 Forklift control switch
188 Second axle load sensor external

(axle c-d)

189 SafeStart
190 SafeStart pressure sensor
191 SafeStart warning lamp
192 Emergency Brake Alert
193 Green warning lamp
194 Brake temperature
195 eTASC rear axle
196 eTASC front axle
197 ECAS single block 2
198 ECAS front axle valve
199 Constrained normal level switch
200 GIO Service indication
201 Shared buzzer
202 Shared warning lamp
203 Service mode
204 GIO operating hours counter

(ServiceMind) warning lamp

205 Output overload indication
206 Output overload indication 3rd

modulator
207 Electronic Park Brake switch
208 Valve spring brake
209 2nd switch
210 Electronic Park Brake valve
211 Door locking system
212 Lift Axle Off Switch
213 Rear monitoring system switch
214 Trailer Length proximity switch 2
215 Trailer Length proximity switch 3

CODES OF MESSAGES

18

Code Message

216 Trailer Length proximity switch 4
217 ECAS ramp level control input switch
220 Data link towing vehicle / trailer (TEBS

D/E)

250 Not used
251 Power supply (TEBS D/E)
253 Parameter settings (TEBS D/E)
254 Trailer modulator (TEBS D/E)

Component IVTM

639 CAN (short circuit / bus off)
927 Warning lamp 2 (optional / pin 4)
928 Warning lamp 1 (standard / pin 2)
929 Tire data cannot be analyzed
1121 Data on the CAN data bus
3011…

3054

Pressure in tire

3111…
3154

Leakage in tires and valves

Code Message

3410…
3500

Tire pressure deviation

Type of fault

00 Value too high
01 Value too low
02 Data is irregular or incorrect
03 Overvoltage / Short circuit to 24 V
04 Undervoltage / Short circuit to ground
05 Supply cable interruption
06 Current too high or circuit grounded
07 Distance too big
08 Slip
09 Signal failure
10 Jump up / Jump down
11 / 12 See failure note
13 Characteristics error
14 Special faults / See fault info
15 See failure note

Notes

CODES OF MESSAGES

19

HINTS

• The display of the menu items results from the tted and parametrized systems.

• All data is for information only.

• The display information or messages correspond to the situation of the last or current

driving operation.

• You can nd a detailed explanation of message codes in the system description of
SmartBoard in the product database INFORM under www.wabco-auto.com.

• Only an authorized workshop is allowed to change SmartBoard batteries (concerns not ADR
version 446 192 111 0)

Switch-on / Switch-off

Power supply Event Consequence

Trailer vehicle coupled:

ISO 7638 Ignition ON Display on

Ignition OFF Display off (with IVTM after

max. 20 min.)

Trailer vehicle uncoupled:

Internal battery of

SmartBoard (not in ADR
version 446 192 111 0)

Pressing of a button (> 2 s) Display on

Pressing of a button Display updated

Notes

HINTS

WABCO (NYSE: WBC) is a leading innovator

and global supplier of technologies that improve

the safety and efciency of commercial vehicles.

Founded nearly 150 years ago, WABCO continues

to pioneer breakthrough products and systems
for braking, stability, suspension, transmission
automation, and aerodynamics. Today, all of the
world’s leading truck, bus and trailer manufacturers
have WABCO technologies onboard. In addition,
WABCO provides the industry with advanced eet
management solutions and aftermarket services.
WABCO reported sales of $2.9 billion in 2014. The
company is headquartered in Brussels, Belgium,
and has 11,000 employees worldwide. For more

information, visit

www.wabco-auto.com

WABCO

© 2015 WABCO All rights reserved 815 010 138 3 / 12.2015

When purchasing a WABCO product, please make
sure it has the typical WABCO product marks
(particularly on packaging, lables and identication
plate) as evidence that it is an original WABCO
part. In case you have any doubts, please contact
your WABCO sales partner.

QUALITY ASSURED

This publication is not subject to any update service.
You will nd the current version on the internet at

http://www.wabco.info/8150101383