V-zug SLQ WP, SL, L 11010, SLQ User Manual

Installation instructions
J11010113-R05
1
Washing machine One-family household
J11010113-R05
10/04/2018
Validity
These installation instructions apply to the models: L (11010), S (11011), SL (11012), SLQ (11013), SLQ WP (11014)
Identification plate
Open the drain tray below the appliance door (see «1. Opening
the appliance door»)
Identification plate 1
Transport
If the weight of the appliance is greater than your lifting capacity, the appliance must be transported by several people or using a transport aid. The weight of the appliance is given on the appliance packaging and in the operating instructions.
Transport the appliance in an upright position only! Transporting it in any other position will cause damage. When carried carefully without being shaken, the appliance may be tilted a maximum of 90° to the right (viewed from the front).
Applicable only to model SLQ WP:
In the event that the appliance is tilted during transportation or installation it must not be put into operation for 2 hours.
Installation accessories supplied
The necessary installation accessories are located in the washing drum and in the appliance packaging.
Designation Article no. Number See installation step
Installation set, incl.:
Rubber stopper
Screw material
External drain hose
Wire hose clamp
Hose support
Installation plate (incl. double-sided adhesive tape)
W41152 1
2 2. Removing the transport lock
1 4. Positioning the installation plate
1 5. Plumbing in
1 5. Plumbing in
1 5. Plumbing in
W40653 1 4. Positioning the installation plate
1
Installation instructions
J11010113-R05
A
1a
B
1b
A
B
C
2
A
D
GE
1.
2.
3.
F
Washing machine One-family household
1. Opening the appliance door (without power)
J11010113-R05
10/04/2018
1a Open drain tray A by
pressing it at the bottom.
Or1bRemove liquid-detergent
flap B from detergent dis­penser drawer C and open drain tray A.
2. Removing the transportation lock
The transport locks F on the rear side have to be removed before using the appliance for the first time.
2 Fold drain tray A
right down and re­move it. Remove emergency door re­lease tool D from bracket.
Insert tool D into blue eye of opening and pull in direction of arrow (arrow on appliance).
1. Remove the hexagon head screws E of the transport locks F using a 10 mm ring or open-end wrench.
2. Push up and pull out the transport lock F.
3. Plug the holes with the rubber stoppers G.
Failure to carry out step3 can result in error messages.
2
Installation instructions
J11010113-R05
180°
180°
957 957
4
2
3
1
213
80
72
160
45
595
33
625
850
(125)
500
577 500 50
(42)
15
84.5
725
550 458 104
Open door 1059*
Left-hand opening Right-hand opening
Open door 1059*
D
S
E
Washing machine One-family household
3. Dimensions
The stated dimensions do not include distances from walls. To prevent disturbing noise and vibration the appliances must not come into contact with the surrounding walls of their installation location.
All models
J11010113-R05
10/04/2018
1 Cold water connection,
inlet hose with Aquastop, length: 1.25 m, G¾"
2 Drainage hose connection with elbow.
Length: 1.5 m Pumping height for drain pump: 1.2 m
3 Electrical connection cable outlet,
length: 1.8 m
4 Installation plate
* In order that the detergent dispenser
drawer can be used without obstruction and be taken out for cleaning, the clear­ance space must be observed across the entire front of the appliance.
4. Positioning the installation plate
Use the installation plate supplied to install the appliance. It fixes the appliance in position, and is for use with both free-standing appliances and appliances positioned in a niche.
The use of an unsuitable installation plate or a soft, sound-insulating underlay can affect the proper functioning of the appli­ance.
Holes must not be drilled in the floor if the room has underfloor heating. The installation plate must be adhered to the floor.
In the location where the appliance is to be installed, fix the in-
stallation plate with 3screws. In the case of underfloor heating, adhere the installation plate to the floor with double-sided ad­hesive tape S.
Dampen the mounting slots E on the installation plate with wa-
ter. This makes it easier to push the appliance in.
3
+ 4 hidden pages