Page 1
Installation instructions
1048746-R01
Built-in control panel
ER2/ER4
Type of construction 55-127
The appliance should be installed by qualified personnel only.
Each step must be carried out and checked in full in the order specified.
1048746-R01
29/01/2018
Validity
These installation instructions apply to:
Built-in wide switch box: 33010, 33013
General notes
General notes
If installing into a combustible material, the guidelines and standards for low voltage installations and fire protection
must be strictly observed.
Identification plate
Affix the second identification plate (supplied) in an accessible position behind the front of the fitted cabinet beneath the appliance.
Electrical connections
Electrical connections must be carried out by qualified personnel in accordance with the guidelines and standards
for low-voltage installations and the specifications of the local electricity supply companies.
A plug-in appliance may only be connected to a socket outlet with earthing contact, installed according to specifications. An
all-pole mains isolating device with 3 mm contact opening should be provided in the house wiring system. Switches, plug and
socket devices, circuit breakers and fusible cut-outs which are accessible after installation and which have all-poles switching
are permissible as isolating devices. Effective earthing and separately installed neutral and earth conductors ensure safe and
fault-free operation. After installation, live parts and cables with basic insulation must not be accessible. Check old installations.
▸ If the appliances are used over an altitude of 2000m above sea level, a reduction in power must be expected.
▸ Refer to the identification plate for information on the required mains voltage, current type and fuse protection.
1
Page 2
Installation instructions
1048746-R01
Identification plate
Connection plate
72.5
72.5
Intermediate base only
removable with tools
60 ≥30
127 3*
56020
≥60 ≥400
205
600
20
550
S2
37
H
S1
A
B
L
470
ø7
405
547
124
G
D
E
F
C
Built-in control panel
ER2/ER4
Type of construction 55-127
Installation
1048746-R01
29/01/2018
*Ventilation slit is not absolutely necessary.
1. Install hob into worktop in accordance with installation instructions.
2. Drill 2 holes L (ø 7 mm) into the base of the cabinet or traverse.
3. Insert screws S1 with washers A into holes L from below and loosely screw both clamping plates B.
4. Open connection box C.
5. Connect mains connection cable D in accordance with connection plate.
– Cable length: With cable inserted, it must be possible to pull switch box about 40cm out of cut-out.
6. Fix earth connection E and use clamp F to secure the strain relief.
7. Insert coupling plug G from hob into switch box. Observing the colour code!
8. Push built-in wide switch box into cut-out and align. Place angle H under the clamping plates B. Adjust height using screws S2.
9. Tighten screws S1.
2
Page 3
Installation instructions
1048746-R01
2
1
Built-in control panel
ER2/ER4
Type of construction 55-127
Operating and display elements
Control panel
The number, type and layout of the elements depend on the model and its features.
1 Cooking zone indicator lights front/back
2 Dial
Dial
The symbols for the different temperature values are on the dials.
1048746-R01
29/01/2018
Operating the appliance
The individual cooking zones are all operated in the same way.
Selecting cooking zone
▸ Set the dial to the required power level.
– The power indicator light illuminates.
For normal cooking zones, the dial can be turned past the «0» power level in both directions.
For dual ring cooking / frying zones, the dial has an end stop. It can only be turned in a clockwise direction and then
back in an anti-clockwise direction.
▸ To switch on the larger cooking zone of a dual ring cooking / frying zone, first turn the dial as far as it will go and then set it to the re-
quired power level.
Overview of power levels
Power level Cooking method Use
1 Melting, gentle warming Butter, chocolate, gelatine, sauces
2
3 Swelling Rice
4 Continue cooking, reducing, stewing, steaming Vegetables, potatoes, sauces, fruit, fish
5
6 Continue cooking, braising Pasta, soup, braised meat
7 Gentle frying Rösti, omelettes, breaded fried foods, sausages
8 Frying, deep frying Meat, chips
9 Flash frying, fast heating Steaks, boiling water
Switching cooking zone off
▸ Set the dial for the required cooking zone to power level «0».
– If none of the other cooking zones are in use, the power indicator light goes out.
3
Loading...