Vulcan-Hart 1T4024E Specifications

Item # __________________________

MODEL 1T4024E

C.S.I. Section 11420

40 QUART 2/3 JACKETED TILTING
KETTLE ON ELECTRIC BOILER BASE

STANDARD FEATURES

2

/3 jacketed tilting steam kettle, 40 quart capacity.

■

■ Steam jacketed kettle mounted on 28" high base cabinet

with stainless steel frame, front full height door, stainless
steel side and aluminized rear panel with 6" adjustable legs
with flanged feet for anchoring.

■ Fully welded hemispheric bottom kettle with type
304 stainless steel jacket and type 316 stainless steel
liner. Jacket tested to 50 psi (3.4 kg/cm

■ Steam control valve on right trunnion leg.

■ 12" single temperature deck mounted faucet.

■ CSD-1 code compliant boiler.

■ Electric 24 KW steam boiler.

■ Requires a 208 or 240 volt, 60 Hz, 3 phase power supply

and a separate 120 volt, 60 Hz, 1 phase control circuit,
3 amp.

■ Water filter system, SPS620V. Includes second year ex­tended limited water associated parts and labor warranty.

■ One year limited parts and labor warranty.

2

).

Vulcan-Hart Co.

ISO9001

A2780

MODEL: 1T4024E

SPECIFICATIONS:

One 40 quart 2/3 jacketed tilting steam kettle mounted on a
24"wide electric boiler base, Vulcan-Hart Model No. 1T4024E.
Steam jacketed kettle mounted on 28" high base cabinet with
stainless steel frame, front full height door, stainless steel side
and aluminized rear panel with 6" adjustable legs with flanged
feet for anchoring. Fully welded hemispheric bottom kettle with
type 304 stainless steel jacket and type 316 stainless steel
liner. Jacket tested to 50 psi (3.4 kg/cm

2

). Steam control valve
on right trunnion leg. 12" single temperature deck mounted
faucet. Requires 208 or 240 volt, 60 Hz, 3 phase power supply
and a separate 120 volt, 60 Hz, 1 phase control circuit, 3 amp.

Exterior dimensions:
Cabinet: 24"w x 35.4"d x 28"h on 6" adjustable legs. Overall
height to the lip of the kettle - 47", to the top of the handle - 59".

U L listed. Classified by U L to NSF Std. #4. Meets ASME code.

OPTIONS

■■ Correction package.

- Cabinet door with hasp (lock by others).

- Security type tamper resistant fasteners.

■■ Tilting kettle strainer.

■■ 12" dual temperature faucet.

■■ Single phase on 24 KW boiler.

■■ Stepdown transformer (eliminates 120 volt connection).

■■ 480 volts, 60 Hz, 3 phase, includes stepdown transformer.

■■ Mount and interconnect kettle with boiler base at factory.

Includes steam supply piping. Shipped on one skid.

■■ Second year extended limited parts and labor warranty.

ACCESSORIES

■■ Stainless steel back panel.

■■ Lift-off cover.

■■ Contour measuring strip.

■■ Single perforated stainless steel basket.

40 Quart

2

/

3

Jacketed Tilting Kettles On Electric Boiler Base

VULCAN-HART COMPANY, P.O. BOX 696, LOUISVILLE, KY 40201, TEL. [phone]

F-32380 (2-06)

502-778-2791 QUOTE & ORDER FAX: [phone]

MODEL 1T4024E

40 QUART 2/3 JACKETED TILTING
KETTLE ON ELECTRIC BOILER BASE

WATER QUALITY STATEMENT:

The fact that a water supply is potable is no guarantee that it is suitable
for steam generation. Your water supply must be within these general
guidelines:

SUPPLY PRESSURE 20 - 60 psig
HARDNESS* less than 3 grains
SILICA less than 13 ppm
TOTAL CHLORIDE less than 4.0 ppm
pH RANGE 7-8
UN-DISSOLVED SOLIDS less than 5 microns

* 17.1 ppm = 1 grain of hardness

Other factors affecting steam generation are iron content, amount of
chloridation and dissolved gases. Water supplies vary from state to state
and from locations within a state. Therefore it is necessary that the local
water treatment specialist be consulted before the installation of any
steam generating equipment.

AMPS PER LINE

MODEL KW

NO. INPUT 208V 240V 208V 240V 480V 240/415V

1T4024E 24 116 100 67 58 29 34

1 PHASE 3 PHASE 220/380V &

TOP VIEW

SERVICE CONNECTIONS:
A Junction box: J.I.C. 6 x 6 x 4 for electrical supply connection for heat.
B Electrical Connection for Controls: 120/60/1, 300 watt power

C Drain: Condensate box, compartment and boiler, 11/4" NPT. (Provide

D Cold Water Connections (2):

E Water Supply Connection for Kettle Filler Faucet:1/4" NPT.

3 PHASE-4 WIRE

NOTE:

• Dimensions which locate the above connections have a tolerance of
+ or -3" (+ or -75 mm).

• Installation of backflow preventers, vacuum breakers and other specific
code requirements is the responsibility of the owner and installer. It is
the responsibility of the owner and installer to comply with local codes.

• Plastic drains are not recommended due to inherent limited tempera­tures of the plastic. Boiler purge temperatures may exceed 180°F.
The installer may be required to provide means to reduce boiler purge
water temperature to be that of the condensate temperature of 140°F
or less.

• This appliance is manufactured for commercial installation only and is
not intended for home use.

supply with grounding wire required.

an open air type drain within 12" of condensate box and for best
results at a distance so that steam vapors will not enter the steamer
from underneath the control area. Do not connect solidly to any drain
connection.)

D1 Treated Cold Water Connection: 1/4" NPT for boiler feed. Inlet

water pressure between 20 and 80 psi.
D2 Untreated Cold Water Connection: 1/4" NPT for condensate

box. Inlet water pressure between 20 and 80 psi.

EQUIPMENT CLEARANCE:

Rear: 2" Right: 0" Left: 0"

BRIMFUL CAPACITIES (in 4 oz. servings):

40 quarts / 10 gallons / 37.5 liters - 320 servings.

FRONT VIEW

NOTE: In line with its policy to continually improve its products, Vulcan-Hart Company reserves the right to change materials and

specifications without notice.

F-32380 (2-06)

VULCAN-HART COMPANY, P.O. BOX 696, LOUISVILLE, KY 40201, TEL. [phone]

502-778-2791 QUOTE & ORDER FAX: [phone]

SIDE VIEW

Printed On Recycled Paper