What’s in the box
1 set for DM111/DM111-2
1 set for DM111;
2 sets for DM111-2
1 set for DM111/DM111-2
Connect
What’s in the box | Overview
NOTES
Use only the parent unit power adapter and
the baby unit power adapter supplied with this
product.
The parent unit power adapter and baby unit
power adapter are intended for a vertical
or floor mount position. The prongs are not
designed to hold the plug in place if it is plugged
into a ceiling, under-the-table, or cabinet outlet.
Make sure the parent unit, the baby unit and the
power adapter cord are out of reach of children.
Both the baby unit and the parent u nit are on
once connected to the power s upply.
Connect the baby unit
NOTE
Make sure the POWER light is on af ter the
power plug is fully inserte d into the power jack
of the baby unit.
•
•
•
•
•
Install batteries for temporary use
Install the batteries on the
parent unit
NOTES
Use 2 x AAA batteries (not included). Alkaline
batteries are recommended. If you use other kind of
batteries, the performance of the baby monitor varies.
The parent unit does not support battery recharging.
Do not mix old and new batteries. Do not mix
alkaline, standard (Carbon-Zinc) or rechargeable
(Ni-Cad, Ni-Mh, etc) batteries.
While you insert the batteries, make sure the
polarities are correct.
When the batteries are installed, the parent unit
turns on.
•
•
•
•
•
You are recommended to use the power
adapter to power up the parent unit for
normal use. If you want to move around
the house with the parent unit, or there i s
a power outage, install two AAA a lkaline
batteries for temporary use.
Slide open the battery compartment
cover.
Flip the ribbon across the battery
compartment.
1.
2.
Replace the batteries when the LOW BATTERY light flashes on the parent unit, or you h ear
a beep every 10 minutes.
Connect | Install batteries for temporary use
Before use
Test the sound transmission of the baby
monitor before initial use, and at regular
times thereafter.
Place the parent unit and the baby unit in
the same room to test the product.
To test the sound transmission:
Speak towards the microphone of the
baby unit. You will hear the sound at
the parent unit, and see the visual
sound indicators light up.
Using your baby monitor
Power on or off the baby unit
To turn on the baby unit:
Press and hold until the POWER light
turns on.
To turn off the baby unit:
Press and hold until the POWER light
turns off.
Power on or off the parent unit
To turn on the parent unit:
Press and hold until the POWER / LINK
light turns on.
To turn off the parent unit:
Press and hold unit the POWER / LINK
light turns off.
Speaker volume of the parent unit
The speaker volume is preset to Level 3
on the parent unit. You can adjust to your
preferred sound level.
To adjust the speaker volume:
Press to decrease the volume, and to
increase the volume.
NOTE
If you continue to press or when the volume
reaches the minimum or max imum setting, the
parent unit will beep once.
To mute the speaker volume:
Press repeatedly until the volume
reaches the minimum.
NOTES
When the parent unit is in mute, the v isual sound
indicator will still indi cate the sound detected
from the baby unit.
To unmute, press repeatedly until it reaches
your desired volume.
•
•
•
•
•
•
•
•
•
•
NOTE
This baby monitor is intended a s an aid. It is
not a substitute for proper adu lt supervision,
and should not be used as such .
Warning: Keep the baby unit out of the re ach
of the baby. Never place or mount the baby uni t
inside the baby’s crib or playp en.
Place the baby unit at least
1 meter / 3 feet away from your baby.
NOTE
If you experience audio feedback on either
the parent unit or baby unit, move the parent
unit further away until there is no more audio
feedback.
•
1.
•
3. Inser t two AAA alkaline batteries into the
battery compartment on top of the ribbon.
4. Sli de the battery compartment cover until
it clicks into place.
Positioning the baby monitor
Install batteries for temporary use (con’t) | Positioning the baby monitor
1
2
3
4
Baby unit overview
1 – POWER light
2 – (On/off)
3 – Microphone
4 – Power jack
Overview
Before use | Using your baby monitor
Parent unit overview
1 – Visual sound indicator
2 – POWER / LINK light
3 – LOW BATTERY light
4 – (Volume down)
5 – (On/off)
6 – Speaker
7 – Belt clip
8 – (Volume up)
9 – Battery compartment cover
10 – Power jack
User’s
Manual
POWER
1
2
3
7
8
9
10
4
5
6
POWER
POWER
POWER
POWER
POWER
POWER
At least 1 meter (3 feet)
POWER
POWER
At least 1 meter
(3 feet)
2. Place the pare nt unit at least
1 meter / 3 feet away from the baby unit.
Connect the baby unit
NOTES
Make sure the POWER / LINK light i s on after
the power plug is fully inser ted into the power
jack of the parent unit.
Make sure the baby unit is on. If the parent unit is
not linked to the baby unit, the POW ER / LINK
light on the parent unit will flash. Move the parent
unit closer to the baby unit (but not less than
1 meter / 3 feet).
•
•
TIP
You can increase the speaker volume of th e
parent unit if you cannot hear the s ounds
transmitted from the baby u nit.
Operating range
The operating range of the baby monitor is
up to 300 meters (1000 feet) outdoors or
50 meters (160 feet) indoors. The actual
operating range may vary depending on
the environmental conditions, and other
interferences such as walls, doors, and
other obstructions.
•
POWER / LINK
DM111
DM111-2
Safe&Sound
®
Digital Audio Baby Monitor
Go to www.vtechphones.com
to register your product for
enhanced warranty support and
latest VTech product news.
User’s manual
Operating range
This product operates with the maximum power allowed by the Federal Communications Commission
(FCC). Even so, the baby unit and the parent unit can communicate over only a certain distance - which
can vary with the locations of the baby unit, the parent unit, the weather, and the layout of your home.
When the parent unit is out of range, it will beep four times every 30 seconds and enter searching mode.
To improve reception, move closer to the baby unit (but not less than 1 meter / 3 feet).
Frequently asked questions
Below are the questions most frequently asked about the b aby monitor. If you cannot find the answer
to your question, visit our webs ite at www.vtechphones.c om or call 1 (800) 595- 9511 for customer
service. In Canada, go to www.vtechcanada.com or call 1 (800) 267-7377.
Why doesn’t the POWER
light on the baby unit turn on
when I switch on the units?
Perhaps the baby unit is not connected to the power supply.
Connect the baby unit to power supply. The baby unit turns on.
Why doesn’t the
POWER / LINK light on the
parent unit turn on when I
switch on the units?
Perhaps the battery of the parent unit is empty and the parent unit is
not connected to power supply.
Connect the parent unit to power supply; or insert two new AAA
alkaline batteries into th e parent unit. The parent unit turns on and
establishes connection with the baby unit.
Why does the baby monitor
not respond normally?
Try the following (in the order listed) for common cure:
1. Make sure that both baby unit and parent unit are on. Disconnect
the power from the baby unit and the parent unit.
2. Remove the batteries from the parent unit.
3. Connect the baby unit to the power supply again. The baby unit turns on.
4. Connect the parent unit to the power supply again; or insert two
new AAA alkaline batteries. The parent unit turn s on.
5. Wait for the parent unit to synchronize with the baby unit. Allow up
to one minute for this to take place.
6. Press or to adjust the speaker volume on the parent unit.
Why does the baby monitor
produce a high-pitched noise?
The units may be too close to each other. Make sure the parent unit
and the baby unit at least 1 meter / 3 feet away from each other.
Why don’t I hear a sound/
Why can’t I hear my baby
cry?
Make sure that both baby unit and parent unit are on. If you see the visual
sound indicators light up, but there is no sound, then you may have muted
the volume or set it to a lower level. Adjust the volume to a higher level.
If the visual sound indicators do not light up, and you cannot hear
any sound, it is because the baby sound is too low for the baby unit
to detect. This is normal. Place the baby unit at least 1 meter / 3 feet
away from your baby.
Why does the parent unit
beep?
The parent unit beeps twice every 5 minute s when the baby unit is
out of range. Move the parent unit closer to the baby unit (but not less
than 1 meter / 3 feet).
If the parent unit is powered by batteries, the parent unit beeps once
every 10 minutes when the battery is low. Replace with two new AAA
alkaline batteries.
Why does the parent unit
LOW BATTERY light flash?
If the parent unit is powered by batteries, the parent unit beeps once
every 10 minutes when the battery is low. Replace with two new AAA
alkaline batteries, or remove the batteries, and connect the parent unit to
the power supply.
Why can’t I establish a
connection? Why is the
connection lost every now
and then? Why are there
sound interruptions?
The baby unit may be out of range. Move the parent unit closer to the
baby unit (but not less than 1 meter / 3 feet).
Other electronic products may cause interference with your baby
monitor. Try installing your baby monitor as far away from these
electronic devices as possible.
Limited warranty
What does this limited warranty cover?
The manufacturer of this VTech Product warrants to the
holder of a valid proof of purchase (“Consumer” or “you ”)
that the Product and all accessories provided in the sales
package (“Product” ) are free from defects in material
and workmanship, pursuant to the following terms and
conditions, when installed and used normally and in
accordance with the Product operating instru ctions.
This limited warranty extends only to the Consumer for
Products purchased and used in the United States of
America and Canada.
What will VTech do if the Product is not free from
defects in materials and workmanship during
the limited warranty period (“Materially Defective
Product”)?
During the limited warranty period, VTech’s authorized
service representative will repair or replace at VTech’s
option, without charge, a Materially Defective Product. If
we repair the Product, we may use new or refurbished
replacement parts. If we choose to replace the Product,
we may replace it with a new or refurbished Product of
the same or similar design. We will retain defective parts,
modules, or equipment. Repair or replacement of the
Product, at VTech’s option, is your exclusive remedy.
VTech will return the repaired or replacement Products to
you in working condition. You should expect the repair or
replacement to take approximately 30 days.
How long is the limited warranty period?
The limited warranty period for the Product extends
for ONE (1) YEAR from the date of purchase. If VTech
repairs or replaces a Materially Defective Product under
the terms of this limited warranty, this limited warranty
also applies to the repaired or replacement Product for
a period of either (a) 90 days from the date the repaired
or replacement Product is shipped to you or (b) the time
remaining on the original one-year warranty; whichever
is longer.
What is not covered by this limited warranty?
This limited warranty does not cover:
1. Product that has been subjected to misuse, accident,
shipping or other physical damage, improper
installation, abnormal operation or handling, neglect,
inundation, fire, water or other liquid intrusion; or
2. Product that has been damaged due to repair,
alteration or modification by anyone other than an
authorized service representative of VTech; or
3. Product to the extent that the problem experienced
is caused by signal conditions, network reliability, or
cable or antenna systems; or
4. Product to the extent that the problem is caused by use
with non-VTech accessories; or
5. Product whose warranty/quality stickers, product serial
number plates or electronic serial numbers have been
removed, altered or rendered illegible; or
6. Product purchased, used, serviced, or shipped for
repair from outside the United States of America
or Canada, or used for commercial or institutional
purposes (including but not limited to Products used for
rental purposes); or
7. Product returned without a valid proof of purchase (see
item 2 on the next page); or
8. Charges for installation or set up, adjustment of
customer controls, and installation or repair of systems
outside the unit.
How do you get warranty service?
To obtain warranty service in the United States of
America, visit www.vtechphones.com or call
1 (800) 595-9511.
In Canada, go to www.vtechcanada.com or call
1 (800) 267-7377.
NOTE: Before calling for service, please review the user’s
manual - a check of the Product’s controls and features
may save you a service call.
Except as provided by applicable law, you assume the
risk of loss or damage during transit and transportation
and are responsible for delivery or handling charges
incurred in the transport of the Product(s) to the service
location. VTech will return repaired or replaced Product
under this limited warranty. Transportation, delivery or
handling charges are prepaid. VTech assumes no risk
for damage or loss of the Product in transit. If the Product
failure is not covered by this limited warranty, or proof of
purchase does not meet the terms of this limited warranty,
VTech will notify you and will request that you authorize
the cost of repair prior to any further repair activity. You
must pay for the cost of repair and return shipping costs
for the repair of Products that are not covered by this
limited warranty.
What must you return with the Product to get
warranty service?
Return the entire original package and contents including
the Product to the VTech service location along with a
description of the malfunction or difficulty; and
Include a “valid proof of purchase” (sales receipt)
identifying the Product purchased (Product model) and
the date of purchase or receipt; and
Provide your name, complete and correct mailing
address, and telephone number.
Other limitations
This warranty is the complete and exclusive agreement
between you and VTech. It supersedes all other
written or oral communications related to this Product.
VTech provides no other warranties for this Product.
The warranty exclusively describes all of VTech’s
responsibilities regarding the Product. There are no
other express warranties. No one is authorized to make
modifications to this limited warranty and you should not
rely on any such modification.
State/Provincial Law Rights: This warranty gives you
specific legal rights, and you may also have other rights,
which vary from state to state or province to province.
Limitations: Implied warranties, including those of fitness
for a particular purpose and merchantability (an unwritten
warranty that the Product is fit for ordinary use) are
limited to one year from the date of purchase. Some
states/provinces do not allow limitations on how long an
implied warranty lasts, so the above limitation may not
apply to you. In no event shall VTech be liable for any
indirect, special, incidental, consequential, or similar
damages (including, but not limited to lost profits or
revenue, inability to use the Product or other associated
equipment, the cost of substitute equipment, and claims
by third parties) resulting from the use of this Product.
Some states/provinces do not allow the exclusion or
limitation of incidental or consequential damages, so the
above limitation or exclusion may not apply to you.
Please retai n your origina l sales receip t as
proof of pur chase.
1.
2.
3.
Technical Specifications
Frequency
control
Crystal controlled PLL
synthesizer
Transmit
frequency
Baby unit:
1921.536-1928.448 MHz
Parent unit:
1921.536-1928.448 MHz
Channels 5
Nominal
effective
range
Maximum power allowed by
FCC and IC. Actual operating
range may vary according to
environmental conditions at the
time of use.
Power
requirements
Baby unit adapter:
Input: 117V AC 60Hz
Output: 6V AC @ 300mA
Parent unit adapter:
Input: 100-120V AC 60Hz
Output: 6V DC @ 400mA
Parent unit battery:
2 X AAA alkaline batter ies
VTech Communications, Inc.
A member of THE VTECH GROUP OF COMPANIES.
VTech is the registered trademark of
VTech Holdings Limited.
Safe&Sound® is a registered trademar k of VTech
Communications, Inc.
Specifications are subject to change without notice.
© 2014 for VTech Communications, Inc.
All rights reserved. 09/14. DM111-X_CIB_V6.0
Document order number : 91-007297-060-100
Designed to fit your home.
And your life.
Technical Specifications
Lights and alert tones | General product care | Storage
Operating range | Frequently asked questions
Congratulations
on purchasing your new VTech product.
Before using this product, pleas e read
Important safety ins tructions.
For support, shopping, and everything
new at VTech, visit our website at
www.vtechphones.com. In Canada,
please visit www.vtechcanada.com.
Limited warranty
Lights and alert tones
Baby unit light
POWER
POWER light
Lights off when the baby uni t is off.
Lights on in green when the baby u nit is on.
•
•
Parent unit light
POWER / LINK
POWER / LINK light
Lights off when the parent u nit is off.
Lights on in green when the pare nt unit is on and linked to the baby unit.
Flashes in green when there is n o link between the baby unit and paren t unit, or
when the parent unit is out of ran ge from the baby unit.
•
•
•
Visual sound indicator
The visual sound indicat or has two functions. One is to sh ow the sound level
detected by the baby unit. The ot her one is to show the volume level during sp eaker
volume setting.
Sound level detected by the baby unit
One to three green lights ind icate a
moderate sound level detecte d by the
baby unit.
Additional red lights in dicate a higher
sound level detected by the baby uni t
(e.g. baby crying loudly) .
•
•
Speaker volume level
One to three green lights ind icate
Level 1 to Level 3 of the speaker
volume setting.
Additional red lights in dicate
Level 4 to Level 5 of the speaker
volume setting.
•
•
LOW BATTERY
LOW BATTERY light
Flashes in red when the batte ry is low.•
Parent unit alert tones
Low battery tone
Beeps once every 10 minutes when the battery is low.•
Out of range tone
Beeps four times every 30 se conds when there is no link betwee n the baby
unit and parent unit, or when the parent unit i s out of range from the baby unit.
•
General product care
To clean and maintain this product:
Avoid putting it near heating appliances and devices that generate electrical noise (for example,
motors or fluorescent lamps).
DO NOT expose it to direct sunlight or moisture.
Avoid dropping the product or treating it roughly.
Clean with a soft cloth.
DO NOT immerse the parent unit and the baby unit in water and do not clean them under the tap.
DO NOT use cleaning spray or liquid cleaners.
Make sure the baby unit and parent unit are dry before you connect them to the power supply.
Storage
When you are not going to use the baby m onitor for some time, remove the batteri es from the parent
unit. Store the parent unit, t he baby unit and the adapters in a cool a nd dry place.
•
•
•
•
•
•
•
Loading...