POWER
POWER
baby’s safety world
Parent Unit
POWER
POWER
Positioning the audio monitor
Place the portable unit within the operating
range of the monitor unit. We recommend the
portable unit is at least 1 meter (3 feet) away
from the monitor unit to avoid audio feedback.
If you still experience audio feedback, move the
portable unit and the monitor unit farther apart.
Operating range
The operating range of the audio monitor
is up to 300 meters (1000 feet) outdoors
or 50 meters (160 feet) indoors. The actual
operating range may vary depending on
the environmental conditions, and other
interferences such as walls, doors, and other
obstructions.
Monitor unit overview
Portable unit overview
User’s manual
DM111/DM111-2
Safe & SoundTM
Digital audio monitor
Congratulations
on purchasing your new V Tech product.
Before using this product, please read
Important safety instructions in this manual.
For support, shopping, and everything new
at VTech, visit our website at
www.vtechcanada.com.
When using your equipment, basic safety precautions
should always be followed to reduce the risk of re,
electric shock and injury, including the following:
1. Follow all warnings and instructions marked on
the product .
2. Adult setup is required.
3. This product is intended as an aid. It is not
a substitute for responsible and proper adult
supervision and should not be used as such.
4. This product is not intended for use as a
medical monitor.
5. Do not use this product near water. For example,
do not use it next to a bath tub, wash bowl,
kitchen sink, laundry tub or swimming pool, or in
a wet basement or shower.
6. CAUTION: Use on ly alkaline batte ries (not
included). There may be a risk of explosion if
a wrong type of battery is used for the portabl e
unit. Do not dispose of batteries in a re. They
may explode. Check with local codes for possible
special disposal instructions.
7. Do not open or mutilate the bat teries. Released
electrolyte is corrosive and may cause burns or
injury to the eyes or skin. The electrolyte may be
toxic if swallowed.
8. Exercise care in handling the batteries in order not
to create a short circuit with conductive materials.
9. Observe proper polarity orientation between the
batteries and metallic contacts.
10. Use only the adapters included with this product.
Incorrect adapter polarity or voltage can seriously
damage the product.
Monitor unit power adapter: Input 117V AC 60
Hz; output: 6V AC 300 mA
Portable uni t power adapter: Input 100-120V AC
60 Hz; output: 6V DC 400 mA
11. The power adapters are intended to be correctly
oriented in a vertical or oor mount position. The
prongs are not designed to hold the plug in place
if it is plugged into a ceiling, under-the-table or
cabinet outlet.
12. Unplug this product from the wall outlet before
cleaning. Do not use liquid or aerosol cleaners.
Use a damp cloth for cleaning.
13.
Unplug the power cords before replacing the batteres.
14. Do not cut off the adapters to replace them with
other plugs, as this causes a hazardous situation.
15. Do not allow anything to rest on the power cords.
Do not install this product where the cords may
be walked on or crimped.
16. This product should be operated only from the type
of power source indicated on the marking label. If
you are not sure of the type of power supply in your
home, consult your dealer or local power company.
17. Do not overload wall outlets or use an extension cord.
18. Do not place this product on an unstable table,
shelf, stand or other unstable surfaces.
19. This product should not be placed in any area
where proper ventilation is not provided. Slots
and openings in the back or bottom of this
product are provided for ventilation. To protect
them from overheating, these openings must
not be blocked by placing the product on a soft
surface such as a bed, sofa or rug. This product
should never be placed near or over a radiator or
heat register.
20. Never push objects of any kind into this product
through the slots because they may touch
dangerous voltage points or create a short circuit.
Never spill liquid of any kind on the product.
21. To prevent re or shock hazard, do not expose
this product to water or any type of moisture.
22. To reduce the risk of electric shock, do not
disassemble this product, but take it to an authorized
service facility. Opening or removing parts of the
product other than specied access doors may
expose you to dangerous voltages or other risks.
Incorrect reassembling can cause electric shock
when the product is subsequently used.
23. You should test the sound reception every time you
turn on the units or move one of the components.
24. Periodically examine all components for damage.
25. Be aware of possible loss of privacy while using
public airwaves. Conversations may be picked
up by other nursery monitors, cordless phones,
scanners, etc.
26. Children should be supervised to ensure that
they do not play with the product.
27. The product is not intended for use by persons
(including children) with reduced physical,
sensory or mental capabilities, or lack of
experience and knowledge, unless they have
been given supervision or instruction concerning
use of the appliance by a person responsible for
their safety.
SAVE THESE INSTRUCTIONS
Cautions
1. Use and store the product at a temperature
between 32oF and 104oF.
2. Do not expose the product to extreme cold, heat
or direct sunlight. Do not put the product close to
a heating source.
3. The batteries should not be exposed to excessive
heat such as bright sunshine or re.
4. Make sure the monitor unit and the adapter cord
are always out of reach of children, at least 1
meter (3 feet) away from the baby or crib, to avoid
a possible strangulation hazard.
5. Other electronic products may cause
interferenc e with your audio mon itor. Try
installing yo ur audio monitor as far away
from these electronic devices as possible:
wireless routers, radios, cellular telephones,
intercoms, room monitors, televisions,
personal computers, kitchen appliances and
cordless telephones.
6. Never place the monitor unit inside the baby’s
crib or playpen.
7. Never cover the monitor unit or portable unit(s)
with anything such as a towel or a blanket.
Precautions for users of implanted cardiac
pacemakers
Cardiac pacemakers (applies only to digital
cordless devices):
Wireless Technology Research, LLC (WTR), an
independent research entity, led a multidisciplinary
evaluation of the interference between portable
wireless devices and implanted cardiac pacemakers.
Supported by the U.S. Food and Drug Administration, WTR recommends to physicians that:
Pacemaker patients
• Should keep wireless devi ces at least six inches
from the pacemaker.
• Should NOT place wireless devi ces directly over
the pacemaker, such as in a breast pocket, when
it is turned ON.
WTR’s evaluation did not identify any risk to
bystanders with pacemakers from other persons
using wireless devi ces.
Electromagnetic elds (EMF)
This VTech product complies with all standards
regarding electromagnetic elds (EMF). If handled
properly and according to the instructions in this
user’s manual, the product is safe to be used based
on scientic evidence available today.
Connect
Connect the portable unit
Before use
You may test the audio monitor before initial
use, and at regular times thereafter.
To test your audio monitor:
1. Place the portable unit and the monitor unit
in the same room to test the product.
2. Press and hold on the monitor unit until
the POWER light turns off.
3. Press and hold on the monitor unit again
until the POWER light turns on.
4. Press and hold on the portable unit the
POWER/LINK light turns of f.
5. Press and hold on the portable unit again
until the POWER/LINK light turns on.
• If the porta ble unit is not linked to
the monitor uni t, the POWER/ LINK light
on the porta ble unit will ash . Move the
portabl e unit closer to the monit
or unit
(but not less than 1 meter / 3 feet).
1 – POWER light
2 – (On/off)
Press and hold to turn on or off the
monitor unit.
3 – Microphone
4 – Power jack
Overview
POWER / LINK
POWER/LINK light
• Lights off when the portable unit
is off.
• Lights on in gree n when the
portabl e unit is on and linked
to the monitor uni t.
• Flashes in gree n when there
is no link betwe en the monitor
unit and por table unit, or whe n
the portab le unit is out of range
from the monito r unit.
Visual sound indicator
The visual sou nd indicator sho ws
the sound level dete cted from
the monitor uni t. It also shows
the volume level duri ng speaker
volume settin g.
Sound level detected from the
monitor unit is indepedent from the
volume level set at the portable unit.
• Green lights in dicate a
moderate soun d level detected
from the monito r unit; or
• Level 1 to Leve l 3 of the
speaker volume set ting.
• Red lights ind icate a higher
sound level detec ted from the
monitor unit; or
• Level 4 to Leve l 5 of the
speaker volume set ting.
LOW BATTERY
LOW BATTERY light
• Flashes in red wh en the
battery is l ow.
POWER
POWER light
• Lights off wh en the monitor
unit is off.
• Lights on in gree n when the
monitor unit is o n.
1 – Visual sound indicator
2 – POWER/LINK light
3 – LOW BATTERY light
4 – (Volume down)
Press to decrease
the speaker volume.
5 – (On/off)
Press and hold to turn on or off the
portable unit.
6 – Speaker
Listen to sounds transmitted from the
monitor unit.
7 – (Volume up)
Press to increase
the speaker volume.
8 – Belt clip
9 – Battery compartment cover
10 – Power jack
Monitor unit light
Portable unit light
Using your audio monitor
Power on or off the monitor unit
To turn on the monitor unit:
• Press and hold until the POWER light
turns on.
To turn off the monitor unit:
• Press and hold until the POWER light
turns off.
Power on or off the portable unit
To turn on the portable unit:
• Press and hold until the POWER /LINK
light turns on.
To turn off the portable unit:
• Press and hold unit the POWER /LINK
light turns off.
1
2
3
4
Connect the monitor unit
• Use only the portable unit power adapter
and the monitor unit power adapter
supplied with this product.
• The portable unit power adapter and
monitor unit power adapter are intended
for a vertical or oor mount position. The
prongs are not designed to hold the plug
in place if it is plugged into a ceiling,
under-the-table, or cabinet outlet.
• Make sure the portable unit, the monitor
unit and the power adapter cord are out of
reach of children.
• Both the monitor unit and the portable unit
are on once connected to the power supply.
Power outlet not
controlled by a
wall switch
Powe r adapt er
Power outlet not
controlled by a
wall switch
Powe r adapt er
POWER
At least 1 meter (3 feet)
Important safety instructions
Parts checklist
• Monitor unit (DM111 BU/DM111-2 BU)
• Portable unit (DM111 PU/DM111-2 PU)
(1 for DM111 and 2 for DM111-2)
• Power adapter for monitor unit
• Power adapter for portable unit
(1 for DM111 and 2 for DM111-2)
• User’s manual
1
2
3
4
5
6
7
8
9
baby’s safety world
Parent Unit
10
POWER / LINK
Below are the questions most frequently asked about
the audio monitor. If you cannot nd the answer to
your question, contact customer service by visiting our
website at www.vtechcanada.com or calling
1 (800) 267-7377.
Why does the audio
monitor not respond
normally?
Try the following (in the order
listed) for common cure:
1. Disconnect the power
from the monitor uni t and
the portabl e unit.
2. Remove the batteries
from the porta ble unit.
3. Connect the mon itor
unit to the power sup ply
again. The moni tor unit
turns on.
4. Connect the port able
unit to the power supply
again; or insert two new
AAA alkaline bat teries.
The portable uni t turns
on.
5. Wait for the portabl e unit
to synchronize with the
monitor units. Allow up to
one minute for this to
take place.
Why doesn’t the
POWER light on the
monitor unit turn on
when I switch on the
units?
Perhaps the monitor unit is
not connected to the power
supply.
Connect the monitor unit to
power supply. The monitor
unit turns on.
Why doesn’t the
POWER/LINK light
on the portable
unit turn on when I
switch on the units?
Perhaps the battery of the
portable unit is empty and
the portable unit is not connected to power supply.
Connect the portable unit to
power supply; or insert two
new AAA alk aline batterie s
into the port able unit. The
portable unit turns on and
establishes connection with
the monitor unit.
Why does the audio
monitor produce a
high-pitched noise?
The units may be too close
to each other. Make sure
the portable unit and the
monitor unit at least 1 meter
(3 feet) away from each
other.
Why does the
portable unit react
too quickly to other
sounds?
The monitor unit also picks
up other sounds. Adjust the
speaker volume on the
portable unit.
Why don’t I hear a
sound?
You may have muted the
volume or set it to a lower
level. You may need to
adjust the volume to a
higher level.
Why does the
portable unit beep?
The monitor units may be
out of range. Move the
portable unit closer to the
monitor units (but not less
than 1 meter / 3 feet).
Why does the
portable unit LOW
BATTERY light
ash?
When the portable unit is
powered by batteries, there
is not sufcient power for
the portable unit to perform
normally. Replace with two
new AAA alkaline batteries.
Why can’t I establish
a connection? Why
is the connection
lost every now and
then? Why are there
sound interruptions?
The monitor units may be
out of range. Move the
portable unit closer to the
monitor units (but not less
than 1 meter / 3 feet).
Other electronic products
may cause interference with
your audio monitor. Try
installing your audio monitor
as far away from these
electronic devices as
possible.
FCC Part 15
This equipment has been tested and found to comply
with the requirements for a Class B digital device
under Part 15 of the Federal Communications
Commission (FCC) rules. These requirements are
intended to provide reasonable protection against
harmful interference in a residential installation. This
equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful
interference to radio communications. However, there
is no guarantee that interference will not occur in a
particular installation. If this equipment does cause
harmful interference to radio or television reception,
which can be determined by turning the equipment
off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment
and receiver.
• Connect the equipment into an outlet on a circuit
different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV
technician for help.
FCC and IC regulations
Frequently asked questions
Speaker volume of the por table unit
The speaker volume is preset to Level 3 on the
portable uni t. You can adjust to your preferred
sound level.
To adjust the speaker volume:
• Press to decrease the volume, and to
increase the volume.
• If you continue to press or even the
volume reaches the minimum or maximum
setting, the portable unit will sound once.
• When the portable unit is in mute, the
visual sound indicator will still indicate the
sound detected from the monitor unit.
• Use only the AAA alkaline
batteries
(not included).
• When the batteries are installed,
the
portabl e unit turns on.
• The porta ble unit does not
Install the batteries on the portable unit
1. Slide open the battery compartment cover.
2. Flip the ribbon across the battery
compartment.
Standby mode
The portable uni t is on standby mode when:
• it is not connected to the AC power supply; and
• there is no sound detected from the
monitor unit.
The standby time varies depending on usage and
the battery life. Full batteries can last up to 8 days.
Replace the batteries when:
• LOW BATTERY light ashes on the portable unit.
• The portable unit beeps twice every 10 seconds.
• The batteries are properly installed into the
portable unit, but the POWER/LINK light on
the portable unit is off.
To clean and maintain this product:
• Avoid putting it near heating appliances and devices
that generate electrical noise (for example, motors or
uorescent lamps).
• DO NOT expose it to direct sunlight or moisture.
• Avoid dropping the product or treating it roughly.
• Clean with a soft cloth.
• DO NOT immerse the portable unit and the monitor
unit in water and do not clean them under the tap.
• DO NOT use cleaning spray or liquid cleaners.
• Make sure the monitor unit and portable unit are
dry before you connect them to the power supply.
This product operates with the maximum power
allowed by the Federal Communications Commission
(FCC). Even so, the monitor unit and the portable unit
can communicate over only a certain distance - which
can vary with the locations of the monitor unit, the
portable unit, the weather, and the layout of
your home.
When the portable unit is out of range, it will beep three
times every 10 seconds and enter searching mode.
To improve reception, move closer to the monitor unit
(but not less than 1 meter / 3 feet).
General product care
Operating range
Changes or modications to this equipment not
expressly approved by the party responsible for
compliance could void the user’s authority to operate
the equipment.
This device c omplies with Par t 15 of the FCC rules.
Operation is s ubject to the foll owing two cond itions:
(1) this device may not cause harmf ul interference,
and (2) this device mus t accept any inter ference
received, inc luding interfe rence that may cause
undesired op eration.
To ensure safety of users, the FCC has established
criteria for the amount of radio frequency energy
that can be safely absorbed by a user or bystander
according to the intended usage of the product. This
product has been tested and found to comply with
the FCC criteria. The monitor unit shall be installed
and used such that parts of all persons’ body are
maintained at a distance of approximately 8 in (20
cm) or more.
This Class B digital apparatus complies with
Canadian requirement:
CAN ICES-3 (B)/NMB-3(B)
For body worn operation, this portable unit has been
tested and meets the FCC RF exposure guidelines
when used with the accessories supplied or
designated for this product. Use of other accessories
may not ensure compliance with FCC RF
exposure guidelines.
Industry Canada
Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference, including
interference that may cause undesired operation.
The term ‘’IC:‘’ before the certication/registration
number only signies that the Industry Canada
technical specications were met.
This product meets the applicable Industry Canada
technical specications.
RF radiation exposure statement
The monitor unit complies with FCC RF radiation
exposure limits set forth for an uncontrolled
environment. The monitor unit should be installed and
operated with a minimum distance of 20 cm (8 inches)
between the monitor unit and all persons’ body. Use
of other accessories may not ensure compliance with
FCC RF exposure guidelines. This transmitter must
not be co-located or operating in conjunction with
any other antenna or transmitter. This equipment
complies also with Industry Canada RSS-102 with
respect to Canada’s Health Code 6 for Exposure of
Humans to RF Fields.
Limited warranty
What does this limited warranty cover?
The manufacturer of this VTech Product warrants to
the holder of a valid proof of purchase (“Consumer” or
“you”) that the Product and all accessories provided
in the sales package (“Product”) are free from
defects in material and workmanship, pursuant to the
following terms and conditions, when installed and
used normally and in accordance with the Product
operating instructions. This limited warranty extends
only to the Consumer for Products purchased and
used in the United States of America and Canada.
What will VTech do if the Product is not free from
defects in materials and workmanship during
the limited warranty period (“Materially Defective
Product”)?
During the limited warranty period, VTech’s
authorized service representative will repair or
replace at VTech’s option, without charge, a
Materially Defective Product. If we repair the Product,
we may use new or refurbished replacement parts.
If we choose to replace the Product, we may replace
it with a new or refurbished Product of the same
or similar design. We will retain defective parts,
modules, or equipment. Repair or replacement of
the Product, at VTech’s option, is your exclusive
remedy. VTech will return the repaired or
replacement Products to you in working condition.
You should expect the repair or replacement to take
approximately 30 days.
How long is the limited warranty period?
The limited warranty period for the Product extends
for ONE (1) YEAR from the date of purchase. If
VTech repairs or replaces a Materially Defective
Product under the terms of this limited warranty,
this limited warranty also applies to the repaired or
replacement Product for a period of either (a) 90 days
from the date the repaired or replacement Product
is shipped to you or (b) the time remaining on the
original one-year warranty; whichever is longer.
What is not covered by this limited warranty?
This limited warranty does not cover:
1. Product that has been subjected to misuse,
accident, shipping or other physical damage,
improper installation, abnormal operation or
handling, neglect, inundation, re, water or other
liquid intrusion; or
2. Product that has been damaged due to repair,
alteration or modication by anyone other than an
authorized service representative of VTech; or
3. Product to the extent that the problem experienced
is caused by signal conditions, network reliability,
or cable or antenna systems; or
4. Product to the extent that the problem is caused by
use with non-VTech accessories; or
5. Product whose warranty/quality stickers, product
serial number plates or electronic serial numbers
have been removed, altered or rendered illegible; or
6. Product purchased, used, serviced, or shipped for
repair from outside the United States of America
or Canada, or used for commercial or institutional
purposes (including but not limited to Products
used for rental purposes); or
7. Product returned without a valid proof of purchase
(see item 2 on the next page); or
8. Charges for installation or set up, adjustment of
customer controls, and installation or repair of
systems outside the unit.
How do you get warranty service?
To obtain warranty service, visit
www.vtechcanada.com or call 1 (800) 267-7377.
NOTE: Before calling for service, please review the
user’s manual - a check of the Product’s controls and
features may save you a service call.
Except as provided by applicable law, you assume
the risk of loss or damage during transit and
transportation and are responsible for delivery or
handling charges incurred in the transport of the
Product(s) to the service location. VTech will return
repaired or replaced Product under this limited
warranty. Transportation, delivery or handling
charges are prepaid. VTech assumes no risk for
damage or loss of the Product in transit. If the
Product failure is not covered by this limited warranty,
or proof of purchase does not meet the terms of
this limited warranty, VTech will notify you and will
request that you authorize the cost of repair prior to
any further repair activity. You must pay for the cost
of repair and return shipping costs for the repair of
Products that are not covered by this limited warranty.
What must you return with the Product to get
warranty service?
1. Return the entire original package and contents
including the Product to the VTech service location along
with a description of the malfunction or difculty; and
2. Include a “valid proof of purchase” (sales receipt)
identifying the Product purchased (Product model)
and the date of purchase or receipt; and
3. Provide your name, complete and correct mailing
address, and telephone number.
Other limitations
This warranty is the complete and exclusive
agreement between you and VTech. It supersedes
all other written or oral communications related to this
Product. VTech provides no other warranties for this
Product. The warranty exclusively describes all of
VTech’s responsibilities regarding the Product. There
are no other express warranties. No one is authorized
to make modications to this limited warranty and you
should not rely on any such modication.
State/Provincial Law Rights: This warranty gives you
specic legal rights, and you may also have other
rights, which vary from state to state or province
Frequency
control
Crystal controlled PLL synthesizer
Transmit
frequency
Monitor unit: 1921.536-1928.448 MHz
Portable unit: 1921.536-1928.448 MHz
Channels 5
Nominal
effective
range
Maximum power allowed by FCC
and IC. Actual operating range may
vary according to environmental
conditions at the time of use.
Power
requirements
Monitor unit ad apter:
Input: 117V AC 60Hz
Output: 6V AC @ 300mA
Portable uni t adapter:
Input: 100-120V AC 60Hz
Output: 6V DC @ 400mA
Portable uni t battery:
2 X AAA alka line batteries
Technical specications
to province.
Limitations: Implied warranties, including those of
tness for a particular purpose and merchantability
(an unwritten warranty that the Product is t for
ordinary use) are limited to one year from the date
of purchase. Some states/provinces do not allow
limitations on how long an implied warranty lasts,
so the above limitation may not apply to you. In no
event shall VTech be liable for any indirect, special,
incidental, consequential, or similar damages
(including, but not limited to lost prots or revenue,
inability to use the Product or other associated
equipment, the cost of substitute equipment, and
claims by third parties) resulting from the use of this
Product. Some states/provinces do not allow the
exclusion or limitation of incidental or consequential
damages, so the above limitation or exclusion may
not apply to you.
Please retain your ori ginal sa les rec eipt as
proof o f purch ase.
3. Insert two AAA alkaline batteries into the
battery compartment on top of the ribbon.
4. Slide the battery compartment cover until it
clicks into place.
Storage
When you are not goi ng to use the audio mo nitor for
some time, remove th e batteries from t he portabl e
unit. Store the po rtable unit , the monitor unit an d the
adapters in a co ol and dry plac e.
Portable use (optional)
VTECH TELECOMMUNICATIONS LTD.
A member of THE VTECH GROUP OF COMPANIES.
VTech is the registered trademark of
VTech Holdings Limited.
Specicat ions are subjec t to change witho ut notice.
© 2014 for VTECH TELECOMMUNICATIONS LTD.
All rights reserved. Version 2 01/14.
Document orde r number: 91-007303 -020-100
DM111-X_EN _UM_V2.0
Designed to t your home.
And your life.
Loading...